KitchenAid KCIP 1010/I User manual

KCIP 1010/I
KCIP 1210/I
Instructions for use

Warnings 4
Safeguarding the environment 5
Instructions for installation and use 6
Extraction modes 6
Installation 7
Hood description 14
Functioning 14
Maintenance 15
After-Sales Service 17

• This appliance should not be used by children or people with limited physical or mental
abilities and with no experience or knowledge of its use, unless they are supervised by
someone in charge of their safety or who has taught them how to use the appliance.
• Children should not play with the appliance.
1. Do not connect the appliance to the mains supply until the installation is completely finished.
Before carrying out any cleaning or maintenance work, always disconnect the hood from the mains
supply by pulling out the plug or turning off the mains switch in the house.
2. Do not flambé food under the hood since the flames generated could cause a fire.
3. Do not leave a frying pan unattended when frying food as the cooking oil could catch fire.
4. Constant cleaning and maintenance of your hood will ensure it works properly. Regularly remove all the
ingrained food from dirty surfaces. Regularly remove and clean or change the filter. Do not use
inflammable material to convey exhaust air.
5. If the hood is used in conjunction with other appliances that run on gas or other fuels, the negative
pressure of the room should be no greater than 4Pa (4 x 10-5 bar). This is why you should make sure
the room is well aired.
6. Exhaust air from the hood should not be eliminated through the heating system chimney or appliances
that run on gas or other fuels.
7. The room should be sufficiently ventilated when the hood is used together with other appliances that
run on gas or other fuels.
8. Before touching the light bulbs, make sure they have cooled down.
Note: always use gloves when installing or carrying out maintenance work.
Electrical connection
The mains voltage should correspond with the voltage shown on the specifications label found inside the
hood. If there is no plug, connect the hood to a socket that complies with current legislation and is in an
easily accessible location. If there is no plug (direct connection to the mains supply) or the plug is not in an
easily accessible location, fit a legally complying bi-polar switch that ensures the complete disconnection of
the mains in the event of a category III line surge, in compliance with the installation regulations.
IMPORTANT: before reconnecting the hood circuit to the power supply, check that it is
working properly, that the mains cable has been properly fitted and that it has NOT been
crushed in its holder during installation.
Cleaning the hood
Warning! Failure to remove oil/grease (at least once a month) could lead to a fire breaking out. Use a soft
cloth and mild cleaning product. Never use harsh substances or alcohol.
Before using the hood
To get best performance from the hood, please read these user instructions carefully and keep them for
future reference.
Keep the packaging material (plastic bags, pieces of polystyrene, etc.) out of children’s reach as they can be
dangerous.
Make sure the hood has not been damaged during transportation.
The installation and the electrical connections, replacement of power cables with plug or flexible cable
should be carried out by a qualified technician in compliance with current legislation in force.
This appliance was designed to be used by adults.
Warnings
4

1. Packing
The packaging material is entirely recyclable and marked with the recycling symbol . Follow local
regulations for scrapping. Keep the packaging materials (plastic bags, polystyrene parts, etc.) out of reach
of children, as they are potentially dangerous.
2. Product
This appliance is marked according to the European Directive 2002/96/EC, Waste Electrical and Electronic
Equipment (WEEE).
By ensuring that this product is disposed of correctly, you will help prevent potentially negative
consequences for the environment and human health.
The symbol on the product or on the documents accompanying the product indicates that this
appliance may not be treated as household waste. Instead, it should be handed over to the applicable
collection point for the recycling of electrical and electronic equipment.
Disposal must be carried out in accordance with local environmental regulations for waste disposal.
For more detailed information on treatment, recovery and recycling of this product, contact your local
authority, the household waste disposal service or the shop where you purchased the product.
Safeguarding the environment
Declaration of conformity
This product has been designed, manufactured and marketed according to the following:
- safety objectives of the “Low Voltage” Directive 2006/95/CE (which replaces 73/23/CEE and
subsequent amendments).
- protection requirements of “EMC” Directive 89/336/EEC amended by Directive 93/68/EEC.
Troubleshooting guide
Hood does not work:
• Is the electrical power supply switched on?
• Is there a power failure?
Insufficient suction power:
• Did you set the right speed?
• Do the filters need to be cleaned or replaced?
• Are the air outlets blocked?
Light does not work:
• Does the bulb need to be replaced?
• Is the bulb correctly fitted?
Warnings
5

This is an excessively heavy product and the movement and installation of the hood should be done by at
least two or more people.
Follow the instructions in this manual carefully. The manufacturer denies all responsibility for damage
or fire to the appliance resulting in failure to comply with the instructions in this manual.
Instructions for installation and use
The hood is designed to be used in two
modes: Venting exhaust fumes to the
outside, or by passing the air through a
charcoal filter before recirculating the air
back into the kitchen.
Vented Mode
The hood comes with an upper air outlet
Bfor the discharge of fumes to the
outside (vented exhaust pipe and fixing
straps are not supplied). Fig. 1
Recirculation Mode
If the fumes and steam from cooking
cannot be discharged towards the
outside, you can use the recirculation
mode by fitting an activated carbon filter
(not supplied, this must be purchased
seperately) and the deflector Fon the
support (bracket) G; the fumes and steam
are recirculated via the upper grid Hand
an exhaust pipe, connected to the upper
air outlet Band the connection ring fitted
to the deflector F(venting exhaust pipe
and fixing straps are not supplied). Fig. 2
Installation
The minimum distance between the
upper pan support surfaces on the
cooking appliance and the lowest part of
the cooker hood should be no less than
50 cm in the case of electrical cookers
and 70 cm in the case of gas or mixed
cookers. If the installation instructions for
the gas cooking appliance specify a greater
distance, then follow that instruction.
Extraction Modes
6

7
The hood comes with plugs suitable for most
walls/ceilings. You should however consult a
qualified technician to make sure the installation is
suitable for your kind of wall/ceiling. The wall/roof
should be sufficiently strong to support the weight
of the hood.
Before installation:
• Check that the product purchased is the right
size for the area where it is to be installed.
• To make installation easier, temporarily remove
the parts that block access to the fixing areas
(e.g.: grease filters, perimetric suction panels
and carbon filter support frames, depending on
which model you have).
• Remove the active carbon filter/s if provided
(again consult relative paragraph). This/these
should be re-assembled only if you wish to use
the hood in the extraction mode.
• Check that there are no parts (e.g. bags with
screws, warranty) inside of the hood (for
transport reasons). If there are, remove them
and put to the side.
• If possible, disconnect and remove the
surrounding units and those near the installation
area of the hood so that you have better
accessibility to the ceiling / wall where the hood
is to be installed. Otherwise, protect the units
as much as possible and all the parts relating to
the installation. Choose a flat surface and cover
it with some protection where you can place
the hood and parts.
• Furthermore, check that near the area where
you are installing the hood (in an area accessible
even when the hood is fitted) there is an
electric socket and that you can connect to an
venting pipe to the outside (In the Vented
mode only).
• Disconnect the electrical power from the
electrical socket connected to the hood at the
main switchboard and remember not to
connect the hood to the mains supply before
completing installation.
• Carry out all the building work necessary (e.g.:
installation of an electrical plug and/or holes to
pass the exhaust venting pipe through).
Fig. 3
• Establish the most suitable distance from the
work surfaces according to your needs
(Important! Respect the minimum distances
specifically indicated in this instruction booklet).
• Adjust the extension of the hood’s support
structure using the mathematical formula shown
in the diagram.
Note: only if you wish to use the hood in
recirculation mode (see also fig. 4 and later
paragraphs): in the case of highly extended
structures, before final assembly remember to
install the deflector so that it will be easier to
handle.
• Fit the two sections of the structure with a total
of 16 screws (8 per side).
Installation

T recirculation
mode
SIDE VIEW
Deflector
Connection
ring
Exhaust
Vent
Pipe
Recirculation mode only
Fig. 4
• Recirculation mode only: fix the deflector to the
frame:
a. Insert the deflector from one side of the
frame so that the rectangular hole at the centre
is facing downwards.
b. Fit the deflector with 4 screws from the top
of the frame.
c. Connect a suitable extraction pipe to the
connection ring provided. It should be long
enough ( with a diameter of 150mm) to reach
the connection ring on the motor unit when it is
installed. Use the mathematical formula in the
diagram to do this.
d. Insert the pipe with the connection ring
upwards and fix it to the deflector with 2 screws.
Installation
8

T
vented
mode
Vented mode only
9
Fig. 5
• Attach the ceiling perforation layout onto the
ceiling (the centre of the layout should
correspond with the centre of the hob and the
sides should be parallel to the sides of the hob –
the side of the layout with the words FRONT
on it corresponds to the side of the control
panel). Prepare the electrical connection.
• Make a hole as shown (4 holes for 4 wall plugs).
Insert the 4 plugs into the holes. Screw in 2
screws into the side holes (right and left),
leaving a space between the screw head and the
ceiling of about 1cm.
These screws will act as a hook for the support
structure.
Fig. 6
• Remove the power cable from the connection
box on the motor unit.
• Connect up the electricity on the ceiling within
the tolerance limits indicated on the template.
• Vented mode only: Install a suitable extraction
vent pipe (with a diameter of 150mm) that is
long enough to reach the connection ring on the
motor unit, when installed.
Use the mathematical formula in the diagram to
do this.
Installation

10
Fig. 7
• Hook the frame to the 2 screws on the ceiling
and fit securely with another 2 screws (front
and back). TIGHTEN ALL THE SCREWS
WELL.
Fig. 8
• Chimney size: the flue comes in a standard
length and can be cut to size.
Note: The height of the flue should be the
same as the frame extension (see the
mathematical formula in Fig. 3)
• Insert the flue in the frame, check that the
welded side is turned to the back (the opposite
side from where the hood control panel will be
when installation is complete). Fit with 2
screws.
Fig. 9
• Hook the motor unit onto the frame on 4
screws previously screwed onto the unit.
Warning! Pass the electrical cable through the
motor unit so that it does not get damaged and
so that it is possible to connect to the electrical
connection box.
Note: the side with the electrical connection
box corresponds with the side (FRONT) where
the control panel will be once the hood has
been installed.
• Securely attach with 2 screws and tighten all 6
screws.
• Connect the power cable to the connection box
and close the box again.
• Connect the extraction vent pipe to the union
ring on the unit.
Installation