KIVOS KDB702 User manual

1
User Manual
7 inch Wireless Video Door Phone

2
Introduction
Thank you for choosing this wireless video door phone. Please read this
Manual carefully to fully understand its usage, perfect functions and simple
operation.
Before using this product, please read these Attentions carefully to ensure
safe and proper operation of this product.
The Company reserves the right to modify this Manual from time to time
without prior notice.
Safety Warning & Attentions
●Please keep this product dry, as rainwater, moisture, humidity and liquids or
moisture content may contain mineral matters that erode the circuit.
●Do not keep this product in any place with high temperature. As high
temperature may shorten the lifespan of electronic device, damage the battery
and cause deformation or melting of certain plastic parts and components.
●Do not keep this product in any place with low temperature. As when being
moved from a place with low temperature to a place with normal temperature,
it may generate humidity inside, which may cause damage of circuit board.
●Do not attempt to dismantle this product. As improper handling by
nonprofessional personnel may cause damage of the device.
●Do not toss, knock or shake this product, as tough operation mode may
damage the motherboard inside the device.
●If this product is made wet by mistake, shut it down, remove the battery, and
restart the product after confirming it complete dry after 24 hours.
●Do not have the metal parts (specially configured interfaces of charger and
data line excluded) in contact with charger interface to avoid short circuit.
●Use clean and dry soft cloth to clean the lens, infrared lamp and light sensor.
！Warning: improper operation will void warranty!！

3
Outdoor unit
Power Customized lithium battery 3400mah
Consumption 400mA
Outline dimension 134*74*31mm
Weight 122g
Environmental condition -10℃~+50℃
Waterproof grade IP55
Placement Hang on outer wall beside the door
Surface material ABS & hardware accessories
Camera 300,000pixels
View angle 120° wide angle
Night vision pattern 2 IR lamp
PIR 3m*100°
Working time 7 hours continuously
Standby time
Charge time 6 hours
External power AC9~16V/DC9~16V
6months

4
Indoor monitor
Power
Customized lithium battery 4000mah
Consumption
600mA
Outline dimension
200*150*27mm
Weight
387g
Environmental condition
0℃~+40℃
Placement
Put on table or hang on wall
LCD size
7" TFT color screen
Wireless communication mode
2.4GHz
Frame rate
20fps
Image Format
JPEG
Working time
6 hours continuously
Standby time
800 hours
Charge time
6.5 hours
External power
DC9-16V
Application distance
About 300 meters in exposed area

5
Product Diagram
Outdoor unit
Indoor monitor

6
Installation Guide
1.outdoor unit shall be installed at 1.4~1.7 meter above the floor, and the camera
shall avoid facing the sunlight directly.
2.Installation steps
A.Fix the rain cover on the wall with screws.
B.Put the outdoor unit into rain cover,and install the screw at the bottom.
3.Connect DC line according to the wiring diagram (the diameter of hole for wire
getting through should be 16~30mm). Red wire (positive pole) connects to point
1; black wire (negative pole) connects to point 2. If powered by AC power, connect
wire to point 1 and point 2.

7
4. Electronic lock and power supply connection, as show below:
If electric lock maintains always open: connect to point 4
If electric lock maintains always close: connect to point 5
Two power lines of lock: one connects to lock, one connects point 6.
Note: electric lock and external power supply should be prepared by user.

8
5. The camera lens can be adjustable.
6. Wall holder

9
7. Table holder
8. Installation of Storage Card
A. Insert the storage card with the correct way as shown in the diagram and
you’ll hear a clicking sound
B. Improper insertion of storage card may cause system failure, please confirm the
correct inserting direction of the card.
C.Take out of the storage card —— push in the storage card until you hear a
clicking sound, then the storage card will pop up

10
Attentions During Installation
Storage cared introduction
Outdoor infrared sensor cannot be hidden or blocked by other objects.
Do not expose the outdoor unit to direct sunlight.
Install the cable correctly, otherwise the doorbell may be damaged.
This product supports TF(micro-SD) card as external storage device,
when there is no storage card in the product, the photo-taking and
video-recording functions are impossible.
If a self-provided storage card is used:
Please use a storage card with Class 2(2MB/Sec) or above.
Up to 32GB storage card supported.
This machine has automatic cyclic storage function, when the storage
card is full, the original file will be overwritten
.

11
Indoor monitor Keys(Functions)
----ON/OFF
----Talking
---- work as confirm key for MENU
---work as monitor key for standby mode
----as exit key for MENU
----work as unlock key when communicating with outdoor unit
----as right moving key for MENU
----work as option key for MENU
----as video key when calling or monitoring
----as option key when calling extension monitor
----work as option key for MENU,
----as photo key when calling or monitoring,
----as entrance key for exposure adjust,
”Bright/Colour/Volume”:
----Increase and reduce for adjustment.
OK
EXIT
MENU
↑
↓

12
Turn on/off
UI operation instruction
Press “MENU” key enter the main menu interface
see&delete photo record.
Can store 180pcs photos. Automatically cover the earliest photo when memory
is full.
video record.
Support 32G Max. TF(micro-SD) card. Automatically cover the earliest video
when memory is full.
Outdoor unit: Install the battery to turn on. Take out the battery to turn
off.(DC/AC9-16V,Lithium battery)。
Indoor Unit: with 4000mah Lithium battery,DC/AC9-16V. Press the “OK” key
for about 3S to turn on. Then, press the “OK” key for about 3S to enter
shutdown interface: select“Yes” to turn off.

13
message for missed call or ring.
Will have the message if miss any call or ring.Can store 10 messages at
most.Message with photo(as setting) or video(as setting).Automatically cover
the earliest message.It will not have new message if indoor unit is shutdown or
power off.
Ring setting.There is 4 default rings.
MP3 format music in TF(micro-SD) card also can play. You can select the ring
as you like（MP3 music name can not include Chinese characters).Meanwhile,
can adjust the ring volume by pressing key. Volume have 6 levels.
Time&date setting.
Can set time,date. For example,12:00 01-09-2018.
Setting.Enter settings.
Backlight time. Standby backlight time 10-60S setting.
Motion sensor. Turn PIR on or off setting.
Auto-video record. Automatically take video record when ringing. If put TF
card in device, setting “automatically record”, it will take video record
automatically when ringing.But if setting “manual record”, it will take
one photo record automatically when ringing.
Alarm setting. Turn on or off the tamper alarm.
Language selection. Have 6 languages,
English,Spanish,German,French,Russian and Chinese.Factory default
language is English.
Advanced setting.
Pairing. Match code, give code, receive code.
Unlock time. Unlock remaining time setting,3S/5S/8S.
SD card formatting. Insert the TF(micro-SD) card, can format the content.
Version. The version number of the device.
MENU

14
Communication instruction
Intercom between indoor unit and outdoor unit.
Under standby status,press “Call”of out door unit--Indoor unit will ring--
Show on screen--Press “OK” key, and show on the screen, then
can talk with each other.
To call/monitor the outdoor unit is to press , if show the on
the screen, which means not able to intercom. Press again, it will
show on the screen, which means can intercom with the outdoor unit.
Under intercom state, press to take photo. Will show on
screen.
Under intercom state,press to take video. Will show on
screen.
Under intercom state,press to unlock door. Will show on
screen.
Press the upper wheel key of indoor unit on the right side. To adjust the
brightness of screen. Will show on screen.
Press the middle wheel key of indoor unit on the right side. To adjust the
contrast ratio of screen.Will show on screen.
Press the third wheel key of indoor unit on the right side. To adjust the
volume.Will show on screen.
If turn on PIR,will automatically take photo or video(require TF card inside),
will show on screen.
During intercom,show on indoor unit screen,the below battery icon is
for outdoor unit power,it will be red color when low power.
the number stands for different indoor unit.The green lines stands for
intercom signal.
EXIT
↓
↑
MENU
EXIT

15
When stand by, press key to monitor outside.
PIR: when turn on the motion sensor, outdoor unit camera sense person
within 2 meters and will take 3pcs photos record (require TF card inside)
automatically.
Anti-tamper alarm of outdoor unit. When rain cover separate from device, it
will alarm with big sound. At the same time, will take 5pcs photos record. Will
show on screen.
Intercom between indoor units.
If there are only 2 indoor units, press key, and can call another
indoor unit.
If there are 3 indoor units,to call another 2 indoor units. Press
key to call the smaller ID no. between the 2 indoor units. Press
key to call the bigger ID no. between the indoor units.
Pairing Instruction
EXIT
1V1 Match code: (put outdoor unit next to the Indoor monitor)
Select “code” in setting on indoor monitor -- press OK key-- enter into the
match code mode.
Meanwhile, long press the “Reset” hole on outdoor unit back, until you hear
one “Beep” sound, then release.
When indoor monitor displays “Successful”, outdoor unit have “di-di-di”
three sounds, means matching successfully.
If matching failed in 16 seconds, indoor monitor shows “failed”, the outdoor
unit makes ”di” sound. Pleas try above steps again.
NOTE: By default, the monitor is paired well with the outdoor unit.
OK
↑
↓

16
1V2 (add the 2nd monitor)- Match code :
Select “Give code ” on the 1st paired indoor monitor --press OK key--enter into
the giving code mode.
On the new (second) indoor monitor, select “receive code” -- press OK key. It will
have “di-di-di” three sounds, and displays ”Successful” on the screen, which
means matching the 2nd monitor ok.
1V3(add the 3rd monitor) - Match code:
Select “Give code ” on the 2nd paired indoor monitor –press OK key-- enter
into the giving code mode.
On the new (third) indoor monitor, select“receive code”-- press OK key. It
will have “di-di-di” three sounds, and displays “successful” on the screen,
which means matching the 3rd monitor ok.
Add one more outdoor unit - Match code
Select “Give code ” on any one paired indoor monitor --press OK key--
enter into giving code mode.
On the new (second) outdoor unit: Long press the “reset” hole until you
hear “di-di,” two sounds. If match successfully, outdoor unit will have “di-
di-di” three sounds, and means adding the 2nd outdoor unit ok.
After matching ok, please use the No. 2 outdoor unit to call all indoor
monitors for testing. if not ok, please repeat the above steps again.

17
Package Include
Statement
Outdoor unit *1
Indoor monitor *1
Manual *1
Rain cover *1
Wall hang holder *1
Charger *2
DC line *1
Lithium battery 3400mA/h *1
Lithium battery 4000mA/h *1
Screw M3 *1
The standard configuration for door phone is one indoor monitor and one
outdoor unit. The door phone has finished code match and can be used
directly.
If you need more pieces of indoor monitors or outdoor units, please contact
your local distributors (Maximum 2 outdoor units to 3 indoor monitors
supported).
For the added units, please reference the Give Code and Receive Code in the
Code Menu.

18
General faults and solutions
Fault
Cause(s)
Solution(s)
Can not start up
Neglected to press switch button
Press switch button
Lithium battery is not installed
Install lithium battery
Low battery
Charge up lithium battery
No connection to power adapter
when battery runs out
Connect to power adapter
Can not charge
Adapter connector doesn’t
connect to charging port of
machine correctly
Reconnect correctly
Adapter doesn’t connect to 110V--
240V alternating current
Plug into the socket to connect to
alternating current
Outdoor unit
cannot call or
connect to Indoor
monitor
Code match failed
Clear code, and re-match code
Image has noisy
point or flickers
Handset is placed near to TV player,
microwave oven, daylight lamp or
mobile phone which produces
electromagnetic wave interference.
Keep handset far away from the
interference items
No signal for
Indoor monitor
Outdoor unit doesn’t connect to
the power
Connect to the power
Distance between outdoor unit and
Indoor monitor is too far
Adjust to appropriate distance
Disturbed by magnetic field around
Keep handset far away from magnetic field.