Klëarvue Cabinetry TALL CABINET User manual

TALL CABINET
To nd all Klëarvūe Cabinetry® installation instructions and installation videos, visit www.klearvuecabinetry.com
KIT INCLUDES:
A- Bottom B- Shelf C- Top D- Backers
E- Nailers (H1) Cam Lock
x4
(H2) Cam Lock Screw
x4
(H3) Dowel
x16
(H4) Conrmat Screw
x12
Finishing Nails
x24
Cabinet Legs
x4
(H6) Glue Bottle
x1

STEP 1:
• Press cam lock (H1) into shelf (B). A rubber mallet may be used for assistance.
• Install cam lock screws (H2) into the tall cabinet side wall using a Phillips head screwdriver. Screws should line
up with the cam lock. Note: Place cam lock screw in the center of the upright for accurate assembly. Once unit is
assembled completely, this shelf can be moved to accommodate the conguration. Use 32nd hole for 80” height
and 36 hole for 90” height.
• Press shelf onto cam lock screws and secure into place with a quarter turn using a Phillips head screwdriver
Note: Raw end of shelf faces upward.
Finish side faces downward towards oor.
STEP 2:
• Place glue (H6) into pre-drilled dowel holes of the cabinet side wall (sold separately).
• Insert wooden dowels (H3) into glued holes. Note: Roughly half the dowel should t into the hole.
• Apply glue (H6) onto exposed end of inserted wooden dowels (H6).
• Connect bottom piece (A) to dowels on cabinet side wall. A rubber mallet may be used to ensure a tight t.
• Secure bottom piece (A) into place using 3 conrmat screws (H4).
(B)
(B)
(A)(A)

STEP 3:
• Repeat Step 2 for (C) top piece.
• Place glue (H6) into pre-drilled dowel holes of the cabinet side wall (sold separately).
• Insert wooden dowels (H3) into glued holes. Note: Roughly half the dowel should t into hole.
• Apply glue (H6) onto exposed end of inserted wooden dowels (H6).
• Connect top piece (C) to dowels on cabinet side wall. A rubber mallet may be used to ensure a tight t.
• Secure top piece (C) into place using 3 conrmat screws (H4).
STEP 4:
• Place glue (H6) into pre-drilled dowel holes of top piece (C) and bottom piece (A).
• Insert wooden dowels (H3) into glued holes. Note: Roughly half the dowel should t into the hole.
• Apply glue (H6) onto exposed end of inserted wooden dowels (H6).
• Connect the second side wall (sold separately) to dowels on top piece (C) and bottom piece (A). A rubber mallet
may be used to ensure a tight t.
• Secure the second side wall into place using 3 conrmat screws (H4) on each end.
• Repeat step 1 to the second side wall to secure cam lock shelf (B) into place.
Note: Raw end of shelf faces upward.
Finish side faces downward towards oor.
(B)
(A)
(C)
(C)
(A)
(C)
(B)
Note: Before moving onto the next step, place a
spacer under the cabinet so it will be easier to lift
off of the oor.

STEP 5:
• Begin to insert back panels. The below solutions are for a full back. If assembling for a built-in appliance, follow
cut outs on page XX.
• Slide the two 30”H backers (D) into place on the assembled cabinet rst.
• Next slide the 19.5”H backer (D).
• If you are assembling a 90” tall cabinet, insert the 10”H backer (D) last. If you are assembling an 80” tall cabinet,
you will not need this piece.
STEP 6:
• Conrm that the cabinet is square by measuring opposite corner to opposite corner. Adjust as needed.
• Place nailers (E) over the seams of the backers (D) and one nailer ush to the top of the cabinet.
• Secure nailers (E) with provided nishing nails (H5) using a hammer.
(D)
Note: As you attach nailers, make sure backers
(D) are tight against each other to avoid a visible
seam inside of the cabinet.
(D)
(D)
(C)
(E)
(E)
(E)
(E)
(E)

STEP 7:
• With two adults, lift the cabinet upright.
• While rocking the cabinet toward the front, adjust the 2 back legs.
• Once back legs are adjusted, rock the cabinet toward the back and adjust the front legs.
• Secure cabinet to wall into stud, through the nailers.
Note: Cabinet legs should be set
approximately 4-3/4” from nished oor.

FOR BUILT IN APPLIANCES:
• Determine the opening required behind the built in appliance. This information is found in the owners manual of
the appliance. See below for opening sizes per conguration.
• When assembling your tall cabinet, you will need to accommodate your backers (D) to account for the opening
required for the appliance.
• A reinforced shelf will be required to support the weight of your appliance.
• Install llers and/or trim pieces prior to installing built-in appliance. Note: if appliance has a contoured edge
that would allow for unintentional sight lines into the cabinet, an appliance ller (478-3660) can be installed to
conceal view into cabinet. If a gap will appear between the top of your appliance and the bottom of a door, a a
drawer from may be cut down and installed as a ller.
1
1
2
3
4
5
5
6
7
8
9
11 10
PICTURED:
1. Cabinet side wall
2. Top Piece
3. Bottom Piece
4. Shelf
5. Backer
6. Door
7. Drawer
8. Reinforced shelf
9. Filler
10. Appliance ller
11. Major appliance