KLIM KLIM Pods User manual

KLIM Pods
USER MANUAL

English
1. Charging indicators
2. USB charging port
3. Earphone LED indicator
4. Multi-function button
5. Charging contacts
Français
1. Indicateurs de charge
2. Port de chargeUSB
3. VoyantLED de l’écouteur
4. Bouton multifonction
5. Contacts de charge
Deutsch
1. Ladestandsanzeigen
2. USB-Ladeanschluss
3. LED-Anzeige des Kopörers
4. Mehrzwecktaste
5. Ladekontakte
Italiano
1. Spie di ricarica
2. Porta di ricarica USB
3. Spia LED dell’auricolare
4. Pulsante multifunzione
5. Contatti di ricarica
Español
1. Indicadores de carga
2. Puerto de carga USB
3. Indicador LED del auricular
4. Botón multifunción
5. Contactos de carga

Warning: this product contains lithium batteries. Do not
expose it to strong sunlight or fire to avoid risk of damage,
fire or explosion.
Operation and controls
Play / Pause Press the button on either earphone
once
Skip track Press the button on the right earbud
2 times in quick succession
Previous track Press the button on the right earbud
3 times in quick succession
Volume down Press the button on the left earbud 3
times in quick succession
Volume up Press the button on the left earbud 2
times in quick succession
Answer / Finish
Phone Call
Press the button on the right earbud
once to answer or finish a call
Reject incoming
call
Hold the button on the right earbud
for 2 seconds. Release when you
hear a beep to avoid turning off the
earbuds
Voice Control
Press and hold the button on either
earbud for 2 seconds to activate your
device’s voice control (Siri, Google
Voice). In this state, press once to exit
voice control.
ENGLISH

First-time use
Before using the product for the first time, take both
earphones from the case, remove the protective film on the
contacts and put the earphones back in the case. Plug the
case to a computer or outlet using the supplied cable and
fully charge the earphones. This initial charge usually takes
about 2 hours.
The case can charge the earphones 4-5 times before having
to charge it with the cable again.
Charging case LED indicators
• Off: Not charging / fully charged
• Red: Case charging
• Blue: Earphones charging
• Purple: Case and earphones charging
Pairing instructions
1. Take out both earbuds from the charging case at the
same time so they connect with each other and start pairing
automatically (the light flashes in red and blue). If the
earbuds failed to connect, press and hold the multi-function
button for 2 seconds. When connected, the light on the left
earbud turns off while the one on the right earbud is on for
2 seconds.
2. Turn on Bluetooth on your decvice and select “KLIM Pods”
from the list of results. Once connected, the lights on both
earbuds will flash in blue for 2 seconds.
Note: if pairing fails, the blue light will flash slowly and the
earbuds will shut down automatically after 10 minutes.
Put the earbuds back into the charging box and they will
disconnect automatically and start charging. If the paired
Bluetooth device is disconnected or out of range, a new
pairing will be performed.

Single Earbud mode
You can use a single earbud and pair it individually. To do
this, take out only one of the earbuds from the charging case.
The blue LED will flash. Press and hold the control button for
4-5 seconds to bring the earbud into pairing mode and pair
it normally.
Note: volume cannot be adjusted in Single Earbud mode.
To use both earbuds at the same time again, put both
earbuds back into the charging case at the same time. They
will turn off automatically. Take both earbuds out from the
case again to pair them.
IMPORTANT: if the earbuds are not synced with each other
(left earbud flashing in purple), follow these steps to connect
them again:
1. Take the earbuds from the case. Press and hold the two
control buttons on the earbuds for 6 seconds until both
earphones turn off, then release them.
2. Press and hold both control buttons again for 10 seconds,
then put them back in the charging case.
3. Take both earbuds at the same time and they will both
connect to each other automatically.
FAQ, Troubleshooting & Contact
Q: Only one of the ear buds works
A: Check that one of the earbuds is not in Single Earbud
mode.
Q: There are two devices called “KLIM Pods” in the Bluetooth
list on my device
A: Delete both connections, then pair again. If 2 device names
are still showing up, check that the earbuds are not being
used in Single Earbud Mode.
Need more help? Our team of specialists will answer within
24 hours! Please write to [email protected]