Knape&Vogt WUSC12-1-35 User manual

Parts Included
A. Waste Bin(s)
B. Sliding Base Assembly (1)
C. Waste Bin Chassis (1)
D. Lid(s) (if supplied)
E. Extension Brackets (2)
F. #6 x 5/8" Mounting Screws
for Door (8 = 4 + 4 extra)
G. #8 x 1" Mounting Screws
for Sliding Assembly (8 = 6 + 2 extra)
H. #10 - 24" x 1/4" Mounting Screws (4)
for Extension Brackets
SOFT-CLOSE UNDERMOUNT WASTE BIN
Inspect all parts and read all instructions prior to beginning assembly and installation.
310384-A-0913
2700 Oak Industrial Drive NE, Grand Rapids, MI 49505 USA
800.253.1561 • 616.459.3311 • www.kv.com ©2013 Knape & Vogt. All rights reserved. Made in USA. Knape & Vogt®reserves the right to change specifications without notice.
A
Tools Required
• Phillips head screwdriver
• Drill with 1/16" (1.5mm) bit for
drilling pilot holes
• Tape measure or ruler
• Pencil
• Scissors
• WUSC12-1-35PT
• WUSC12-1-35WH
• WUSC15-2-35PT
• WUSC15-2-35WH
• WUSC12-1-50PT
• WUSC12-1-50WH
• WUSC12-2-27PT
• WUSC12-2-27WH
• WUSC18-2-50PT
• WUSC18-2-50WH
Product Assemblies
1. Install Sliding Base Assembly
A. Place sliding base assembly on cabinet floor in the center of the cabinet opening. Refer to chart
(Fig. 1) to determine set back. Position the front edge of the front mounting strap at the
designated set back.
B. Once the position is determined, fasten the sliding base assembly to the cabinet floor by using
4 - #8 x 1" mounting screws through the interior holes. (Fig. 2) Tighten with a screwdriver.
C. Place 2 -#8 x 1" mounting screws through the exterior holes (Fig. 3) and fasten with a Phillips
head screwdriver until the head of the screw is flush with the sliding base assembly.
DO NOT OVER TIGHTEN, as this can warp the slide.
2. Remove Door
With drill or screwdriver, remove door hinges from cabinet and door.
IMPORTANT: Door must be removed prior to waste bin chassis installation.
3. Install Waste Bin Chassis
A. Lower and insert rear of chassis so that the channels on the chassis fit onto the slides on the
sliding base assembly. Push chassis toward the back of the cabinet until it sits against the back
of the slides and you hear a "click." (Fig. 5) The chassis is now fully seated and locked. Grasp the
door mount brakets, slowly pull the chassis out of the cabinet until it stops moving. Both slides
should fully extend.
NOTE: If your slides do not fully extend, your chassis is not seated properly. To correct, push
the drawer slide forward until it locks into position.
Fig. 1
OVERLAY CABINET INSET CABINET
SKU # Cabinet Opening Set Back
Extension
Bracket
Orientation Set Back
Extension
Bracket
Orientation
WUSC12-1-35
11.5-12
14.5-15 2.375
In
Out
2.125" + door thickness
2.375" + door thickness
Not Used
Out
WUSC12-1-50
11.5-12
14.5-15 2.375
In
Out
2.125" + door thickness
2.375" + door thickness
Not Used
Out
WUSC12-2-27
11.5-12
14.5-15 2.375
In
Out
2.125" + door thickness
2.375" + door thickness
Not Used
Out
WUSC15-2-35
14.5-15
17.5-18 2.375
In
Out
2.125" + door thickness
2.375" + door thickness
Not Used
Out
WUSC18-2-50 17.5-18 2.375 Out 2.375" + door thickness Out
Fig. 3 Fig. 5
DO NOT OVER
TIGHTEN
Fig. 2
See
Chart
D
E
B
C
G
FH

B. Loosen the tilt adjusting screw and adjust door mount brackets until they are parallel with the
front of the cabinet according to the diagram shown. (Fig. 6) Once parallel, retighten screws.
4. Determine Door Bracket Position
A. Measure the cabinet opening width. (Fig. 7) Refer to chart (Fig. 1) to determine extension
bracket orientation. If brackets are not required, skip to step 5.
B. Insert one #10 - 24 x 1/4" pan head machine screw in each round hole of the extension
bracket. (Fig. 8) Turn 2 to 3 times.
C. Extend sliding base assembly out of the cabinet interior to a comfortable working position.
Align the pan head screws on the extension bracket with the keyholes in the door bracket.
Insert through keyhole and push downward until the pan head screws are fully seated. If
necessary, loosen the pan head screws slightly to verify screws are fully seated.
Tighten screws. (Fig. 8)
D. Ensure door brackets do not interfere with cabinet opening and set back is in desired location.
If necessary, adjust sliding base assembly accordingly.
5. Install Cabinet Door to Door Bracket
A. Ensure that the chassis in the fully closed position. Peel protective cover from tape on the
brackets. Line up the cabinet door in desired position ensuring that it is level with any cabinet
doors on either side. Also ensure that the spacing between the door and any drawer above is
even with the spacing on your other cabinets. (Fig. 9)
Fig. 6
Fig. 8
Fig. 7
Fig. 9

B. Press the cabinet door against the door brackets firmly to ensure the door adheres to the double sided tape.
C. Grasp the bottom of the cabinet door and slowly open the sliding assembly until you have easy access to the door brackets.
D. Install #6 x 5/8" mounting screws in the center of each of the four horizontal slots shown. (Fig. 10A, 10B and 10C)
E. Ensure your door is centered by closing the unit into the cabinet.
6. Adjust Door Angle
A. Using the door, push trash unit back into the cabinet until it stops. If there is a gap between the top of the door and the cabinet,
adjust the door bracket by loosening the tilt adjusting screw and pivot the door to the desired position. Ensure door is in the desired
position, then install a second locking screw in location shown. (Fig. 11)
B. Place waste bin(s) in chassis. Installation is now complete.
Fig. 10A
Fig. 10C Fig. 11
Without Extension Brackets With Extension Brackets - In
With Extension Brackets - Out
Pivot Screw Locking Screw
(End-User Installed)
Tilt Adjusting Screw
Fig. 10B