Knightsbridge FLS15BK Instruction Manual

97
230V
50Hz
INSTALLATION & MAINTENANCE MANUAL
FLS SERIES FLOODLIGHTS

These instructions should be read carefully and retained after installation by the end user for future
reference and maintenance.
These instructions should be used to aid installation of the following products
FLS15BK / FLS15PBK / FLS30BK / FLS30PBK / FLS50BK / FLS50PBK / FLS70BK / FLS130BK
GENERAL INSTRUCTIONS
SAFETY
INSTALLATION
• Installation of this luminaire should only be carried out by a qualified electrician or competent
person to the current IEE Wiring Regulations (BS7671)
• Before installation/maintenance, ensure that the mains supply to the luminaire is switched off and
the circuit fuses are removed or switched off
• Check the total load on the circuit (including when this luminaire is fitted) does not exceed the
rating of the circuit cable, fuse or circuit breaker
• Please note the IP (Ingress of Protection) rating of this luminaire when deciding the location for
installation
• This product is class I rated and must be earthed
• Please recycle this unit
• This product is non-dimmable
• Outdoor electrical installations should be protected by an earth leakage circuit breaker such as a
residual current device (RCD), this will cut the power supply should it detect a leakage of current to
earth which is potentially dangerous
• Standard product is IP65, PIR version is IP44
Note - If this luminaire is being used in
conjunction with external PIR sensors,
please confirm with the manufacturer
of the sensors that they are compatible
with LED luminaires.
• Provide a suitable power supply to
the required position of the luminaire,
note the information in the PIR
section below
• Unfasten the bolts at the sides of the
mounting bracket and remove the
bracket from the fitting noting order of
washers and fasteners

• Using the bracket as a template, mark the location of the fixing holes. Drill the holes for the fixings
ensuring not to infringe with any joists, gas / water pipes or electrical cables that may be hidden
behind the surface. Important: subject to the surface foundation material, ensure the correct
fixings are used
• Fix the bracket to the mounting surface
• Reattach the fitting to the wall bracket ensuring the washers are in the correct order
• These luminaires are pre-wired with approximately 500mm of 3 core mains flexible cable
Opening and tampering with internal connections will invalidate any warranty
• If installed outside, the mains cable should be connected into a suitable IP rated junction box.
Connect the mains cable to the terminal block ensuring there are no exposed conductors or trapped
insulation and observing correct polarity (see below)
BROWN – LIVE, BLUE – NEUTRAL, GREEN/YELLOW – EARTH
• Switch the power supply on and test for correct operation
GENERAL
PIR
• The LED lamps fitted in this product are non-replaceable. The product should be recycled in the
correct manner when it reaches the end of its life.
• Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which may
damage the product
Before choosing a mounting point please note the following:
PIR sensors are activated and more responsive to sources crossing their paths rather than
approaching them directly.
Avoid positioning the PIR sensor facing trees or shrubbery as well as bright lights and sources of
heat or moving traffic, swinging objects etc.
Avoid positioning where the sensor will be in direct sunlight as this may disturb the sensitivity of the
sensor.
Air temperature and weather changes can affect the sensor and adjustments may be required from
time to time
BROWN (L) LIVE
GREEN/YELLOW (E) EARTH
BLUE (N) NEUTRAL

ML Accessories Limited
LU5 5TA
www.mlaccessories.co.uk SBAUG17_V2
OVERRIDE FACILITY
INITIAL PIR SETUP
The unit may be used for a constant light source.
To override the PIR, switch the power to the light on and off twice in fast repetition, on the second
ignition the light should remain on constant and the PIR will become ineffective. To return to PIR
mode turn the power off and wait a minimum of 2 minutes before switching on again, the unit will
then return to initial PIR response.
For optimum use of all its features, including manual override, we suggest wiring using the PIR
floodlight in conjunction with a single pole wall switch.
The unit has 3 controls
Lux (ambient light sensitivity) 10- 2000lux
Time delay: 10 sec - 7 minutes
Sensitivity or range adjustment: 2m – 7m max.
The range of detection is 180 degrees
(subject to installation)
If testing during daylight ensure lux control is set
to maximum. For night testing ensure lux control
is set to low.
The optimum height for installation is 2.5m.
Sensitivity and range will be limited and
subject to change depending on installation
and the characteristics of the area in which it is
operating.
WARRANTY
This product has a warranty of 3 years from date of purchase. Failure to install this product in
accordance with the current edition of the IEE Wiring regulations, improper use or removal of the
batch codes will invalidate the warranty. If this product should fail within its warranty period it should
be returned to the place of purchase for a free of charge replacement. ML Accessories does not
accept responsibility for any installation costs associated with the replacement product.
Your statutory rights are not affected. ML Accessories reserve the right to alter product specification
without prior notice.
Sens/range Time Lux