Knightsbridge SFR9905 Series Instruction Manual

INSTALLATION & MAINTENANCE MANUAL
SFR9905xx

These instructions should be read carefully and retained after installation by the
end user for future reference and maintenance.
These instructions should be used to aid installation of the following product:
SFR9905xx
GENERAL INSTRUCTIONS
SAFETY
• This product must be installed in accordance with the latest edition of the IEE Wiring
Regulations (BS7671) and current Building Regulations. If in any doubt, consult a
qualified electrician
• Please isolate mains prior to installation or maintenance
• Check the total load on the circuit (including when this product is fitted) does not exceed
the rating of the circuit cable, fuse or circuit breaker
• Please note the IP (Ingress Protection) rating of this product when deciding the location
for installation
• Do not overload this accessory or subject it to conditions outside its rating
• This product is Class I and must be earthed
• This product is for indoor use only
• This product is IP20 rated

WIRING ACCESSORIES MANUAL
These instructions should be read carefully and retained after installation by the end user for future reference and
maintenance.
These instructions should be used to aid installation of the following product:
SFR9905xx
SAFETY
•This product must be installed in accordance with the latest edition of the IEE Wiring Regulations
(BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician
•Please isolate mains prior to installation or maintenance
•Check the total load on the circuit (including when this product is fitted) does not exceed the rating of the
circuit cable, fuse or circuit breaker
•Please note the IP (Ingress Protection) rating of this product when deciding the location for installation
•Do not overload this accessory or subject it to conditions outside its rating
•This product is Class I and must be earthed
•This product is for indoor use only
•This product is IP20 rated
INSTALLATION
•Always ensure the wall surface is flat and smooth
•This unit is fitted with a gasket – this must not be removed: the gasket is to stop discolouration of the
plate due to natural moisture in some wall finishes
•This product must be fitted only after painting and decorating is complete
•Remove the front plate by placing a medium size flat-head screwdriver in the notch at the side and lever
off gently
•Connect to the mains supply ensuring the correct polarity is observed (see Fig. 1): L – Live (brown),
E – Earth (green/yellow), N – Neutral (blue)
Fig. 1
•All earth connections must be made and maintained. Use green/yellow sleeving on earth conductors
that are not insulated
•Check all electrical connections are secure with all exposed copper within the terminal and no loose
strands of cable.
•Fit the unit into a suitable wall box taking care not to compress, damage or trap any cables, and secure
with the screws provided.
•Clip the front plate onto the main assembly ensuring the screwdriver notch is at the side
•Switch on and check for correct operation
BLUETOOTH CONNECTION
•Press the power button directly under the speaker. The Bluetooth indicator will begin to flash
•Activate Bluetooth pairing on your mobile device and scan for Bluetooth devices
•Connect to the device named SPEAKER, SPEAKER01, SPEAKER02 etc
•Once a connection has been established you will hear a “beep” sound and the Bluetooth indicator will
flash at a different frequency to confirm
Bluetooth audio specification:
•Output power: max. 3W RMS
INSTALLATION
• Always ensure the wall surface is flat and smooth
• This unit is fitted with a gasket – this must not be removed: the gasket is to stop
discolouration of the plate due to natural moisture in some wall finishes
• This product must be fitted only after painting and decorating is complete
• Remove the front plate by placing a medium size flat-head screwdriver in the notch at the
side and lever off gently
• Connect to the mains supply ensuring the correct polarity is observed (see Fig. 1): L – Live
(brown), E – Earth (green/yellow), N – Neutral (blue)
Fig. 1

• All earth connections must be made and maintained. Use green/yellow sleeving on earth
conductors that are not insulated
• Check all electrical connections are secure with all exposed copper within the terminal and
no loose strands of cable.
• Fit the unit into a suitable wall box taking care not to compress, damage or trap any
cables, and secure with the screws provided.
• Clip the front plate onto the main assembly ensuring the screwdriver notch is at the side
• Switch on and check for correct operation
• Press the power button directly under the speaker. The Bluetooth indicator will begin to
flash
• Activate Bluetooth pairing on your mobile device and scan for Bluetooth devices
• Connect to the device named SPEAKER, SPEAKER01, SPEAKER02 etc
• Once a connection has been established you will hear a “beep” sound and the Bluetooth
indicator will flash at a different frequency to confirm
Bluetooth audio specification:
• Output power: max. 3W RMS
• Sensitivity: L/R 380MV
• SNR: >80dB
• Speaker frequency range: 280Hz – 16KHz
BLUETOOTH CONNECTION

This product is designed for charging portable USB devices only and contains a short
circuit and overload protection feature. If there is no power from the USB socket unplug
the connected device. Check to ensure the USB socket and USB device have not come into
contact with water, liquid or debris and the cable to the device is not damaged. With no device
connected to the USB socket it will automatically reset and be ready for use.
WARNING
GENERAL
This product must be disconnected from the circuit if subjected to any high voltage or
insulation resistance testing. Irreparable damage will occur if this instruction is not followed.
Please note that we do not recommend our 13A sockets be used for Electric Vehicle (EV)
charging for prolonged periods.
This product should be recycled in the correct manner when it reaches the end of its life.
Check local authorities for where facilities exist.
Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which
may damage the product.
USB CHARGING FUNCTION

WARRANTY
This product has a warranty of 2 years from date of purchase. Failure to install this product
in accordance with the current edition of the IEE Wiring Regulations (BS7671), improper
use, or removal of the batch code will invalidate the warranty. If this product should fail
within its warranty period, it should be returned to the place of purchase for a free of
charge replacement. ML Accessories does not accept responsibility for any installation
costs associated with the replacement product. Your statutory rights are not affected. ML
Accessories reserve the right to alter product specification without prior notice.

Manufacturers Declaration of Conformity
For ML Accessories (Knightsbridge)
Electrical products in accordance with CE marking
ML Accessories Ltd. Declare that all products have been designed, manufactured, and tested in
accordance with the requirements of the relevant legislation
CE marking legislation
In Accordance with the following Directives:
2014/35/EU Low Voltage Directive
2014/30/EU EMC Directive
2014/53/EU Radio Equipment Directive
Including Legislation
1907/2006 REACH
2015/863 RoHS
2021/341 ERP
Safety Standards
Full individual declarations and specific safety standards applicable to relevant product series can be found on
our website www.mlaccessories.co.uk
We hereby declare that the equipment named above has been designed to comply with the relevant
sections of the above referenced specifications. The product complies with all essential requirements of
the directives.
Scott Brewer Catherine Connolly
Technical Manager CEO
ML Accessories Ltd. Unit E Chiltern Park, Boscombe Road, Dunstable. Bedfordshire, LU5 4LT
This declaration becomes invalid if technical or operational modifications are introduced without ML Accessories Ltd. written consent.

Manufacturers Declaration of Conformity
For ML Accessories (Knightsbridge)
Electrical products in accordance with UKCA marking
ML Accessories Ltd. declare that all products have been designed, manufactured, and tested in
accordance with the requirements of the relevant legislation
UKCA marking legislation
UK SI 2016 No. 1091 Electro Magnetic Compatibility Regulations 2016
UK SI 2016 No. 1101 The Electrical Equipment (Safety) Regulations 2016
UK SI 2012 No. 3032 Restriction of the use of Certain Hazardous Substances in Electrical and
Electronic Equipment Regulations 2012
UK SI 2017 No. 1206 Radio Equipment regulations 2017
UK SI 2021 No. 1095 The Ecodesign for Energy-Related Products and Energy
Information (Lighting Products) Regulations 2021
Included Legislation
UK SI 2008 No. 2852 UK REACH
UK SI 2013 No. 3113 WEEE
Safety Standards
Full individual declarations and specific safety standards applicable to relevant product series can be found on
our website www.mlaccessories.co.uk
We hereby declare that the equipment named above has been designed to comply with the relevant
sections of the above referenced specifications. The products comply with all essential requirements of
the directives.
Scott Brewer Catherine Connolly
Head of Technical CEO
ML Accessories Ltd. Unit E Chiltern Park, Boscombe Road, Dunstable. Bedfordshire, LU5 4LT
This declaration becomes invalid if technical or operational modifications are introduced without ML Accessories Ltd. written consent.

DCJUN22_V1
11
Supplied By:
(UK) Manufacturer
ML Accessories Ltd, Unit E Chiltern Park, Boscombe Road, Dunstable LU5 4LT,
www.mlaccessories.co.uk
(EU) Authorised Representative
nnuks Holding GmbH, Niederkasseler Lohweg 18,
40547 Düsseldorf, Germany,
Email: [email protected]om