Koala Kare 885-KIT Guide

Tools Required:
Phillips Head Screwdriver or 1/8” Allen Wrench
1. Open Baby Changing Station. Remove the
screws that secure the old strap to the unit.
Discard old strap and screws.
2. Position the new strap on the unit with the
buckle towards the liner dispenser. (See Image).
3. For all models, take one of the Phillips Pan
Head Machine Screws. Insert it through the hole
in the chafe tab and into the hole in the front of
the bed. Secure the screw into the screw insert.
4. Repeat step 3 for the other end of the strap.
For KB200 model use the other Phillips Pan Head
Machine Screw. For KB100 and KB110 models
use the Truss Head Wood Screw.
5. Ensure that the strap is buckled. Clean up
mess and close unit.
KB100, KB110 and KB200 REPLACEMENT STRAP
INSTRUCTIONS
P/N 885-KIT
Koala Kare Products ǁ 6982 S Quentin St. ǁ Centennial, CO 80112 Toll Free: 888.733.3456 ǁ 303.539.8300 ǁ Fax: [phone]
www.koalabear.com
®
P/N 496 January 2011
Hardware Supplied
Two 5/8” Phillips Pan Head Machine Screws One Truss Head Wood Screw
KB100 KB110 KB200

Materials Supplied: Materials Needed:
Shock     FlatHeadScrewdriver
Key
1.Unlockthelinerdispenserwiththekey(included)andremove
thefourscrewssecuringthelinerdispensertotheframe.Remove
plasticlinerdispenserfromwall.
2.Thereshouldbesixscrewsholdingthemetalmountingframeto
thewall.Removethefourlowermountingscrews.Keepallofthese
screwstoremounttheunit.
3.Loosentheuppertwomountingscrews,butdonotremovethem.
Youshouldbeabletolifttheunitofftheuppermountingscrews
usingthekeyholeslots.
4.Oncetheunitisremovedfromthewall,allowtheunittoclose
andlayitatonanon-abrasivetableorcountertopwiththeframe
sidefacingup.
5.Usingaatheadscrewdriver,releasethe“C”clip(whichholds
thebottomoftheshocktotheballstud)byslidingthescrewdriver
betweenthe“C”clipandtheheadoftheshock.Oncereleasedpull
theheadoftheshockofftheballstud.Repeatthisfortheotherend
oftheshock.
6.Takethenewshockandattachthethinendtotheballstud
closesttothebedoftheunitbypushingituntilyouhearitclickinto
place.Twisttheheadbackandforthtoensureitissecure.
7.Taketheotherendoftheshockinonehandandthewallportion
oftheframeintheother.Slightlypullupontheframeuntilthehead
oftheshocklinesupwiththeballstud.Pushtheshockontothe
ballstuduntilitclicksintoplace.Twisttheheadbackandforthto
ensureitissecure.
8.Remounttheunitusingthekeyholeslotsandthescrewsthat
wereleftinthewall.Replacethefourlowermountingscrewsthat
wereremoved.Tightenallsixscrewstoensuretheunitissecured
tothewall.
9.Reattachthelinerdispensertotheframeusingthefourscrews
youremovedearlier.Closeandlockthelinerdispenserwiththekey
(included).
10.Openandclosetheunitseveraltimestoensuretheshockis
workingcorrectly.Cleantheunitandworkarea.
®
KoalaKareProductsǁ6982SQuentinSt.ǁCentennial,CO80112  TollFree:888.733.3456ǁ303.539.8300ǁFax:303.539.8399
www.koalabear.com
KB200 REPLACEMENT SHOCK INSTRUCTIONS
P/N 472-KIT
P/N307December2010
Frame
Ball Stud
Slightly lift frame
until ball stud and
shock head line up.
“C” Clip
Screwdriver
Ball Stud
Ball Stud
Thin End of
Shock

Items Included:
Bungee Cord
1. Unlock and open the liner dispenser lid to
expose the liner dispenser cavity.
2. If the old bungee cord is still in place remove it
along with any liners in the cavity.
3. On the left and right sides of the liner dispenser
cavity there are keyhole slots. Take the new
bungee cord and insert one of the metal tabs at
the ends of the bungee cord into one of the slots.
Twist the bungee cord so that the metal tab is
horizontal across the inside of the slot and pull it
up to the top of the slot.
4. Repeat the process for the opposite side
ensuring that you keep tension on the rst side
while you install the second side.
5. Once both sides are secure, pinch the middle
of the bungee cord together to create a loop. Pull
the loop towards the top of the liner dispenser
and insert it over the recessed tab between the
liner cavities.
6. Fill the liner cavities with new liners, close and
lock the liner dispenser lid. Close the unit.
KB200 BUNGEE CORD REPLACEMENT INSTRUCTIONS
P/N 481-KIT
Koala Kare Products ǁ 6982 S Quentin St. ǁ Centennial, CO 80112 Toll Free: 888.733.3456 ǁ 303.539.8300 ǁ Fax: [phone]
www.koalabear.com
®
P/N 359 December 2010
Bungee
Keyhole
slot
Keyhole
slot
Bungee