Kobold DAG-A4B Series User manual

Operating Instructions
for
Digital Indicating Unit
PT1000 2-wire -200°C…850°C / -328°F…1562°F
Model: DAG-A4B…, 96 x 48 mm

DAG-A4B
page 2 DAG-A4B/K0123
We don’t accept warranty and liability claims neither upon this publication nor in
case of improper treatment of the described products.
The document may contain technical inaccuracies and typographical errors. The
content will be revised on a regular basis. These changes will be implemented in
later versions. The described products can be improved and changed at any time
without prior notice.
© Copyright
All rights reserved.
1. Contents
1.Contents ........................................................................................................ 2
2.Note .............................................................................................................. 3
3.Instrument Inspection .................................................................................... 4
4.Regulation Use ............................................................................................. 4
5.Assembly ...................................................................................................... 5
6.Electrical connection ..................................................................................... 6
7.Function and operation description ............................................................... 7
8.Setting up the device ..................................................................................... 8
8.1Switching on ........................................................................................ 8
8.2Standard parameterisation ................................................................... 8
8.3Extended parameterisation ................................................................ 10
9.Functional principle of the set points ........................................................... 12
10.Factory settings ........................................................................................... 13
10.1Default values .................................................................................... 13
10.2Reset to default values ...................................................................... 13
11.Technical Information .................................................................................. 14
12.Order Codes ............................................................................................... 14
13.Safety advice .............................................................................................. 15
14.Error elimination .......................................................................................... 16
15.Disposal ...................................................................................................... 17
16.EU Declaration of Conformance ................................................................. 18
Manufactured and sold by:
Kobold Messring GmbH
Nordring 22-24
D-65719 Hofheim
Tel.: [phone]
Fax: [phone]
E-Mail: [email protected]
Internet: www.kobold.com

DAG-A4B
DAG-A4B/K0123 page 3
2. Note
Please read these operating instructions before unpacking and putting the unit into
operation. Follow the instructions precisely as described herein.
The instruction manuals on our website www.kobold.com are always for currently
manufactured version of our products. Due to technical changes, the instruction
manuals available online may not always correspond to the product version you
have purchased. If you need an instruction manual that corresponds to the
purchased product version, you can request it from us free of charge by email
([email protected]) in PDF format, specifying the relevant invoice number and
serial number. If you wish, the operating instructions can also be sent to you by
post in paper form against an applicable postage fee.
Operating instructions, data sheet, approvals and further information via the QR
code on the device or via www.kobold.com
The devices are only to be used, maintained and serviced by persons familiar with
these operating instructions and in accordance with local regulations applying to
Health & Safety and prevention of accidents.
When used in machines, the measuring unit should be used only when the
machines fulfil the EC machinery directive.

DAG-A4B
page 4 DAG-A4B/K0123
3. Instrument Inspection
Instruments are inspected before shipping and sent out in perfect condition.
Should damage to a device be visible, we recommend a thorough inspection of the
delivery packaging. In case of damage, please inform your parcel service /
forwarding agent immediately, since they are responsible for damages during
transit.
Scope of delivery:
The standard delivery includes:
 Digital Indicating Unit model: DAG-A4B
4. Regulation Use
Any use of the device, which exceeds the manufacturer’s specification, may
invalidate its warranty. Therefore, any resulting damage is not the responsibility of
the manufacturer. The user assumes all risk for such usage.

DAG-A4B
DAG-A4B/K0123 page 5
5. Assembly
Please read the Safety advice on page 13 before installation and keep this user
manual for future reference.
1. After removing the fixing elements, insert the device.
2. Check the seal to make sure it fits securely.
3. Click the fixing elements back into place and tighten the clamping screws by
hand. Then use a screwdriver to tighten them another half a turn.
CAUTION! The torque should not exceed 0.1 Nm!
The dimension symbols can be exchanged before installation via a channel
on the side!

DAG-A4B
page 6 DAG-A4B/K0123
6. Electrical connection
DAG-
A
4B0
DAG-A4B4
DAG-
A
4B2
with power supply 230 VAC
with power supply 115 VAC
with
p
ower su
pp
l
y
24 VAC
with power suppl
y
24 VDC
Powe
r
Supply
230 VAC or
115 VAC or
24 VAC

DAG-A4B
DAG-A4B/K0123 page 7
7. Function and operation description
Operation
The operation is divided into two different levels.
Menu Level
Here it is possible to navigate between the individual menu items.
Parameterization Level
The parameters stored in the menu item can be parameterized here. Functions
that can be adjusted or changed are always indicated with a flashing of the display.
Adjustments made at the parameterisation level should be always confirmed by
pressing the [P] key to save them. However, the display automatically saves all
adjustments and then switches into operation mode if no further keys are pressed
within 10 seconds.

DAG-A4B
page 8 DAG-A4B/K0123
8. Setting up the device
8.1 Switching on
Once the installation is complete, you can start the device by applying the current
loop. Check beforehand once again that all the electrical connections are correct.
Starting sequence
For 1 second during the switch-on process, the segment test (8 8 8 8) is displayed,
followed by an indication of the software type and, after that, also for 1 second, the
software version. After the start-up sequence, the device switches to operation /
display mode.
8.2 Standard parameterisation
To be able to parameterize the display, press the [P] key in operating mode for 1
second. The display then changes to the menu level with the first menu item TYPE.

DAG-A4B
DAG-A4B/K0123 page 9

DAG-A4B
page 10 DAG-A4B/K0123
8.3 Extended parameterisation
By pressing the [ ] & [ ] buttons during standard parameterisation for 1 second,
the display switches to the extended parameterisation mode. Operation is the
same as in standard parameterisation.