Kobold ADI-1F Series User manual

Operating Instruction
Operating
Instruction
for
Universal Indicating Unit
Frequency input: 0.01 Hz bis 99.99 kHz
Co
nn
ect
i
o
n f
o
r NAM
U
R-
,
NPN-
,
PNP-
a
n
d
TTL-
se
n
so
r
s
Co ect o o U
,
,
ad
se so s
Model: ADI-1F... 96x96 mm
96x96
ADI-1F.pdf Stand: K04/0522

Identification
Options – break-down ordering code:
ADI-1F000200
Standard type ADI
Bargraph and Digital display, red
Bargraph 55 points 270°, digital display 5-digit, 14 mm 1
Type of display
Frequency input 0.01 Hz – 99.99 kHz F
Power supply
100-240 VAC +/- 10% (50-60Hz) / DC 0
10-40 VDC / 18-30 VAC 50/60 Hz 3
Analogue output
without 0
0-10 VDC, 0/4-20 mA, 16 bit reversible 4
Sensor supply
without 0
5VDC/20mA
U
5
VDC
/
20
mA
U
12 VDC / 50 mA, incl. digital input V
24 VDC / 50 mA, incl. digital input W
Setpoints
2 relay outputs 2
Housing
Housing
Panel mounting housing 0
Field housing F
Field housing with wall mounting finally rotatable S
Field housing with pipe mounting R
Special
without
0
without
0
Special please specify in clear text Y
2

Contents
1. Brief description 5
2. Assembly 6
3
Electrical connection
3
.
Electrical
connection
8
4. Description of function and operation 10
5. Setting up the device 12
5.1. Switching on 12
5.2. Standard parameterisation (flat operation level) 12
Value assignment for the triggering of the signal input of the digital display and bargraph display
53 P i i t l k5.3. Programming interlock „RUN“ 17
Activiation/Deactivation of the programming interlock or change into professional operation level
respectively back into flat operation level
5.4. Extended parameterisation (professional operation level) 18
5.4.1. Signal input parameters „INP“
Value assignment for the triggering of the signal input incl. linearisation of the digital display and
the bargraph display
5 4 2 General device parameters FCT“5.4.2. General device parameters „FCT 22
Superior device functions like HOLD, TARA, min/max permanent, setpoint value function /
nominal value function, averaging, brightness control, as well as the control of the digital input and
keyboard layout
5.4.3. Bargraph functions „bar“
Assignment of the bargraph to superior functions like min/max, totaliser, HOLD or
sliding averaging
5 4 4 Safety parameters Cd“5.4.4. Safety parameters „Cod“29
Assignment of user and master code for locking respectively for access to defined parameters
like e.g. analog output and alarms, etc.
5.4.5. Analog output parameters „Out“30
Analog output functions
5.4.6. Relay functions „rel“32
Parameters for the definition of the setpoints
547 Al t “5.4.7. Alarm parameters „AL1…AL4“34
Actuator and dependencies of the alarms
5.4.8. Totaliser (Volume metering) „tot“36
Parameters for the calculation of the sum function
6. Reset to factory settings 37
Reset parameters to delivery state
7. Alarms / Relay 38
Functional principle of the switching outputs
8. Programmer examples 39
Examples of use e.g. the calculation of the input frequency or the adjustment of unknown
rotational speed
9. Technical data 41
10. Safety advices 43
11. Error elimination 44
3
12. EU Declaration of Conformance 45
18
27

4
Manufactured and sold by:
Kobold Messring GmbH
Nordring 22-24
D-65719 Hofheim
Tel.: [phone]
Fax: [phone]
E-Mail: [e-mail]
Internet: www.kobold.com
The instruction manuals on our website www.kobold.com are always for currently
manufactured version of our products. Due to technical changes, the instruction
manuals available online may not always correspond to the product version you have
purchased. If you need an instruction manual that corresponds to the purchased
product version, you can request it from us free of charge by email
([e-mail]) in PDF format, specifying the relevant invoice numberand serial
number. If you wish, the operating instructions can also be sent to you by post in paper
form against an applicable postage fee.

1. Brief description
1. Brief description
The panel meter instrument ADI-1F is a 5-digit digital display with a 55 points bargraph display
and two galvanic insulated setpoints; designed for pulse signals respectively 2- and 3-wire
sensors
The
configuration
happens
via
four
keys
at
the
front
The
integrated
programming
sensors
.
The
configuration
happens
via
four
keys
at
the
front
.
The
integrated
programming
interlock prevents unrequested changes of parameters and can be unlocked again with an
individual code. Optional the following functions are available: a supply for the sensor, a digital
input for triggering of Hold (Tara), two analog outputs and interfaces for further evaluating in the
unit. The electrical connection is done via plug-in terminals on the back side.
Selectable functions like e.g. the recall of the min/max-value, an averaging of the measuring
signals, a nominal presetting or setpoint presetting, a direct threshold value regulation during
o
p
eration mode and furthe
r
measurin
g
set
p
oints fo
r
linearisation, com
p
lete the modern device
p
g
p
p
concept.
Technical features:
• red display of -19999…99999 digits
• red 55 points bargraph
• adjustable bar or dot operation or operation with permanent display of center point
• min/max memory
• display adjustment via frequency presetting or directly on the sensor signal
• 30 ad
j
ustable set
p
oints
jp
• display flashing at threshold value exceedance/undercut
• Schmitt-Trigger-input
• zero-key for triggering of HOLD, TARA
• permanent min/max-value recording
• digital frequency filter for contact bounce suppression and interference suppresion
• frequency filter with varying pulse control factor
• volume metering (totaliser) for frequencies up to 1kHz (accurate to a pulse)
• mathematical function like reciprocal value, square root, rounding
• sliding averaging with an optional dynamic display filter
• setpoint generator
• brightness control
• programming interlock via access code
• protection class IP65 at the front side
• plug-in screw terminal
• sensor supply
• galvanic insulated digital input
• 2 relay output
• optional analog output
5

2. Assembly
2. Assembly
Please read the Safety advice on page 37 before installation and keep this user manual
for future reference.
56 mm
82 mm with plug-in terminal
Sealing
9
6 mm
9
Fixing
ele
ment
96 mm
7 mm
ele
1. After removing the fixing elements, insert the device.
2. Check the seal to make sure it fits securely.
3. Click the fixing elements back into place and tighten the clamping screws by hand.
Then use a screwdriver to tighten them another half a turn.
CAUTION! The torque should not exceed 0.1 Nm!
Please state you favorite dimension symbol in your order, they can not be
exchanged afterwards!
6

2.2 Mounting field housing
2. Montage
For the assembling of ADI-1 field housing please use the M4 screws. Optionally the housing can
be delivered with wall mounting or pipe mounting For the electrically connection please pull the
be
delivered
with
wall
mounting
or
pipe
mounting
.
For
the
electrically
connection
please
pull
the
housing lead back.
S1 S2
P
OBOLD
ADI-1
P
7

3. Electrical connection
3. Electrical connection
Model ADI-1V000200 with supply of 100-240 VAC
Model ADI-1V300200 with supply of 10-40 VDC
Attention!
For devices with sensor supply, terminal clamps 4 and 18, aswell as 3 and 19 are connected galvanically in
the device.
8

3. Electrical connection
ADI-1F with a frequency input / pulse input
9

4. Description of function and operation
4. Description of function and operation
Operation
The operation is divided into three different levels.
Menu level (delivery status)
This level is for the standard settings of the device. Only menu items which are sufficent to set the
device into operation are displayed. To get into the professional level, run through the menu level
and parameterise “prof“ under menu item RUN.
Menu group level (complete function volume)
Suited for complex applications as e.g. linkage of alarms, setpoint treatment, totaliser function etc. In
this level function groups which allow an extended parameterisation of the standard settings are
availabe. To leave the menu group level, run through this level and parameterise „uloc„ under menu
item RUN.
Parameterisation level:
Parameter deposited in the menu item can here be parameterised. Functions, that can be changed
or adjusted, are always signalised by a flashing of the display. Settings that are made in the
parameterisation
level
are
confirmed
with
[P]
and
thus
safed
By
pressing
the
zero
key“
it
leads
to
Level Key Description
parameterisation
level
are
confirmed
with
[P]
and
thus
safed
.
By
pressing
the
„
zero
-
key“
it
leads
to
a break-off of the value input and to a change into the menu level. All adjustments are safed
automatically by the device and changes into operating mode, if no further key operation is done
within the next 10 seconds.
Menu level
Change to parameterisation level and deposited values.
Keys for up and down navigation in the menu level.
Change into operation mode.
Parameterisation
level
To confirm the changes made at the parameterization level.
Adjustment of the value / the setting.
Change into menu level or break-off in value input.
Change to menu level
Menu group level
Change
to
menu
level
.
Keys for up and down navigation in the menu group level.
Change into operation mode or back into menu level.
10

4. Description of functions and operation
Funktion chart:
11

5. Setting up the device
5. Setting up the device
5.1. Switching-on
Once the installation is complete, you can start the device by applying the voltage supply. Before,
Once
the
installation
is
complete,
you
can
start
the
device
by
applying
the
voltage
supply.
Before,
check once again that all electrical connections are correct.
Starting sequence
For 1 second during the switching-on process, the segment test (88888) is displayed, followed by an
indication of the software type and, after that, also for 1 second, the software version. After the
starting sequence, the device switches to operation/display mode.
5.2. Standard parameterisation:
(flat operation level)
Menu level Parameterisation level
Selection of the in
p
ut si
g
nal
,
tYPE:
5.2.
Standard
parameterisation:
(flat
operation
level)
To parameterize the display, press the [P] key in operating mode for 1 second. The display then
changes to the menu level with the first menu item TYPE.
pg,
Default: fre9u
If the scaling of the device is done via SEnS.F (Sensor calibration), the frequency range needs to
be preset under rAnGE and is adjusted by application of the final value /initial value. If FrEqU
(Factory calibration) is preferred, the final value needs to be entered under End and the final
f
d
t
b
td
d
d
Ud
th
iitil
l
d
t
b
td
d
f
requency nee
d
s
t
o
b
een
t
ere
d
un
d
er En
d
A.
U
n
d
er OFFS
th
e
i
n
iti
a
l
va
l
ue nee
d
s
t
o
b
een
t
ere
d
an
d
under OFFSA the initial frequency. There is no application of the measuring signal. Confirm the
selection with [P] and the display switches back to menu level.
Setting the end value of the measuring range, END:
Default: 100e3
Choose between six different frequency ranges. Confirm the selection with [P] and the display
9.9999 Hz 99.999 Hz 999.99 Hz 9.9999 kHz
99.999 kHz 999.99 kHz
switches back to menu level.
Setting the final value of the measuring range, END:
Default: 10000
12
Set the final value from the smallest to the highest digit with [▲][▼] and confirm each digit with
[P]. A minus sign can only be parametrized on the highest value digit. After the last digit, the
display switches back to the menu level. If Sens was selected as input option, you can only select
between noca and cal.With noca, only the previously set display value is taken over, and with cal,
the device takes over both the display value and the analogue input value.

5. Setting up the device
Menu level Parameterisation level
Setting
the
start/offset
value
of
the
measuring
range
offs
:
Setting
the
start/offset
value
of
the
measuring
range
,
offs
:
Default: 0
Enter the start/offset value from the smallest to the highest digit [▲][▼] and confirm each digit
with
[
P
]
.
A
fter the last di
g
i
t
the dis
p
la
y
switches back to the menu level. If Sens.F was selected as
[]
g
py
the input option, you can only select between
n
oca and cal.With
n
oca, only the previously set
display value is taken over, and with cal, the device takes over both the display value and the
analogue input value.
Setting the decimal point, dot:
Default: 0
The decimal point on the display can be moved with [▲][▼] and confirmed with [P].The
display then switches back to the menu level again.
Setting up the display time, SEC:
Default: 1.0
The display time is set with [▲] [▼]. The display moves up in increments of 0.1 sec up to 1 sec
and in increments of 1.0 sec up to 10.0 sec. Confirm the selection by pressing the [P] button.
The display then switches back to the menu level again.
Rescaling
the
measuring
input
values,
EndA
:
then
Rescaling
the
measuring
input
values,
EndA
:
Default:
1
0000
With this function, you can rescale the input value of e.g. 8.000 Hz (works setting) without
applying a measuring signal. If sensor calibration has been selected, these parameters are not
available
available
.
Rescaling the measuring input values, OFFA:
Default: 0
With this function, you can rescale the input value of e.g. 100 Hz (works setting) without
13
applying a measuring signal. If sensor calibration has been selected, these parameters are no
t
available.

5. Setting up the device
Menu level Parameterisation level
Setting
of
the
impulse
delay
dELAY
Setting
of
the
impulse
delay
,
dELAY
:
Default: 0
With the impulse delay of 0 – 250 s (max), frequencies can be collected, which are even
smaller than by the predetermined measuring time of the device. If e.g. a delay of 250 seconds
is set
,
this means that the device waits u
p
to 250 seconds for an ed
g
e
,
before it assumes a 0
,
p
g,
Hz-frequency. Thus frequencies up to 0.004 Hz can be collected.
Adjustment of the optimum digital frequency filter, fi.frq:
Default: NO
If the optional filter is not activated by the adjustment „No“, frequences are ignored by the
adjusted frequency filter. Act on the assumption that the pulse-duty factor is 1:1. Accordingly
the minimal pulse duration is derived from the half of the time of oscillation. Use a filter of 10 Hz
or 20 Hz for contact bounce suppression.
Setting up the final value of the bargraph, b.EN:
Default
:
1000
Default
:
1000
Set the final value from the smallest to the highest digit with [▲][▼] and confirm each digit
with [P]. A minus sign can only be parameterized on the highest value digit. After the last digit,
the display switches back to the menu level.
Setting
up
the
initial
value
of
the
bargraph
b
f
Setting
up
the
initial
value
of
the
bargraph
,
b
.o
f
:
Default: O
Set the initial value from the smallest to the highest digit with [▲][▼] and confirm each digit
with [P]. A minus sign can only be parameterized on the highest value digit. After the last digit,
the
display
switches
back
to
the
menu
level
the
display
switches
back
to
the
menu
level
.
Selection of the bargraph functions, b.fc:
Default: bar.fo
14
The bargraph can be displayed with the following possibilites: bars from left to right (top to
bottom) or bars from right to left (bottom to top), bars from the middle, a dot display of the
bargraph or a dot display with a permanently displayed midpoint. Confirm the selection by
pressing the [P] button. The display then switches back to the menu level again.

5. Setting up the device
Menü-Ebene Parameter-Ebene
Selection
of
analog
output
Out
rA
:
Selection
of
analog
output
,
Out
.
rA
:
Default: 4‐20
Three output signals are available: 0-10 VDC, 0-20 mA and 4-20 mA, with this function, the
demanded signal is selected.
Setting up the final value of the analog output, Out.En:
Default: 10000
The final value is adjusted from the smallest digit to the highest digit with [▲][▼]and digit by
di
g
it confirmed with
[
P
]
.
A
minus si
g
n can onl
y
be
p
arameterised on the hi
g
hest di
g
it.
A
fter the
g
[]
g
y
p
g
g
last digit, the device changes back into menu level.
Setting up the initial value of the analog output, Out.OF:
Default: 00000
The final value is ad
j
usted from the smallest di
g
i
t
to the hi
g
hest di
g
it with
[
▲
]
[
▼
]
and di
g
it b
y
j
g
g
g
[
]
[
]
g
y
digit confirmed with [P]. A minus sign can only be parametrised on the highest digit. After the
last digit, the device changes back into menu level.
Threshold values / limit values, LI‐1:
Default: 2000
For both limit values, two different values can be parameterized. With this, the parameters for
each limit value are called up one after another.
Hysteresis for limit values, HY‐1:
Default: 00000
The delayed reaction of the alarm is the difference to the threshold value, which is defined by
the hysteresis.
15

5. Setting up the device
Menu level Parameterisation level
Function
if
display
falls
below
/
exceeds
limit
value
FU
1
Function
if
display
falls
below
/
exceeds
limit
value
,
FU
‐
1
:
Default: high
The limit value undercut can be selected with Louu (LOW = lower limit value) and limit value
exceedance can be selected with high (HIGH = upper limit value). If e.g. limit value 1 is on a
switching threshold of 100 and occupied with function „high“, the alarm will be activated by
hi
th
th h ld
If
th
li it
l
i
ll t d
t
“
l
ill
b
ti t d
b
reac
hi
ng
th
e
th
res
h
o
ld
.
If
th
e
li
m
it
va
l
ue
i
sa
ll
oca
t
e
d
t
o„Low
“
,ana
l
arm w
ill
b
eac
ti
va
t
e
d
by
undercut of the threshold. See page 29.
Threshold values / limit values, LI‐2:
Default: 3000
For both limit values, two different values can be parameterized. With this, the parameters for
each limit value are called up one after another.
Hysteresis for limit values, HY‐2:
Default: 00000
The delayed reaction of the alarm is the difference to the threshold value, which is defined by
the hysteresis.
Function if display falls below / exceeds limit value, FU‐2:
Default: high
The limit value undercut can be selected with Louu (LOW = lower limit value) and limit value
exceedance can be selected with high (HIGH = upper limit value). If e.g. limit value 1 is on a
switching threshold of 100 and occupied with function „high“, the alarm will be activated by
reaching the threshold. If the limit value is allocated to „Low“, an alarm will be activated by
undercut of the threshold.
User
code
(
4
-
digit
number
-
combination
free
available)
U
CodE
:
User
code
(
4
-
digit
number
-
combination
,
free
available)
,
U
.
CodE
:
Default: 0000
If this code is set (>0000), all parameters are locked, if LOC has been selected before under
menu item run. By pushing [P] during operation mode for approx. 3 seconds, Code appears in the
display
To
get
to
the
unlocked
reduced
parameter
the
user
needs
to
enter
the
preset
U
Code
16
display
.
To
get
to
the
unlocked
reduced
parameter
,
the
user
needs
to
enter
the
preset
U
.
Code
.
This code has to be entered before each parametrisation, until the A.Code (Master code) unlocks
all parameters again.

5. Setting up the device
Menu level Parameterisation level
Master
code
(
4
-
digit
number
-
combination
free
available)
A
CodE
:
Master
code
(
4
-
digit
number
-
combination
free
available)
,
A
.
CodE
:
Default: 1234
With this code, all parameters can be unlocked, if LOC has been activated before under menu
item run.B
y
p
ushin
g
[
P
]
durin
g
o
p
eration mode for a
pp
ro
x
. 3 seconds
,
Code a
pp
ears in the
y
pg
[]
g
p
pp
,
pp
display. The user can now reach all parameters by entering A.codE. Leaving the parametrisation,
under menu item run, the user can unlock them permanently by choosing ULOC or ProF. So, there
is no need for anew code entering, even by pushing [P] during operation mode again.
5.3. Programming interlock „run“
Activation / deactivation of the programming lock or completion of the standard
parameterisation with change into menu group level (complete function range), run:
Default
:
uloc
Default
:
uloc
With the navigation keys [▲][▼], you can choose between the deactivated key lock Uloc (works
setting) and the activated key lock Loc, or the menu group level ProF. Confirm the selection with
[P]
.
After
this,
the
display
confirms
the
settings
with
"‐‐‐‐‐"
,
and
automatically
switches
to
[P]
.
After
this,
the
display
confirms
the
settings
with
,
and
automatically
switches
to
operating mode. If Loc was selected, the keyboard is locked. To get back into the menu level,
press [P] for 3 seconds in operating mode. Now enter the CODE (works setting 1234)that
appears using [▲][▼]plus[P] to unlock the keyboard. FAIL appears if the input is wrong.
To parameterise further functions ProF needs to be set. The device confirms this setting with „‐
‐‐‐‐„and changes automatically in operation mode. By pressing [P] for approx. 3 seconds in
operation mode, the first menu group InP is shown in the display and thus confirms the change
into the extended parameterisation. It stays activated as long as ULOC is entered in menu group
RUN
thus
the
display
is
set
back
in
standard
parameterisation
again
RUN
,
thus
the
display
is
set
back
in
standard
parameterisation
again
.
17

5. Setting up the device
5.4. Extended parameterisation (Professional operation level)
5.4.1. Signal input parameters
Menu group level
Menu level
5.4.1.
Signal
input
parameters
Menu level Parameterisation level
Selection of the input signal, tYPE:
Default: fre9u
If the scaling of the device is done via SEnS.F (Sensor calibration), the frequency range needs to
be preset under rAnGE and is adjusted by application of the final value /initial value. If FrEqU
(Factory calibration) is preferred, the final value needs to be entered under End and the final
frequency needs to be entered under EndA. Under OFFS the initial value needs to be entered and
under OFFSA the initial frequency. There is no application of the measuring signal. Confirm the
selection with [P] and the display switches back to menu level.
Setting the end value of the measuring range, END:
Default: 100e3
9.9999 Hz 99.999 Hz 999.99 Hz 9.9999 kHz
Choose between six different frequency ranges. Confirm the selection with [P] and the display
switches back to menu level.
Setting the final value of the measuring range, END:
Default
:
10000
99.999 kHz 999.99 kHz
Default
:
10000
Set the final value from the smallest to the highest digit with [▲][▼] and confirm each digit
with [P]. A minus sign can only be parametrized on the highest value digit. After the last digit,
the
display
switches
back
to
the
menu
level
.
If
Sens
was
selected
as
input
option,
you
can
only
18
the
display
switches
back
to
the
menu
level
.
If
Sens
was
selected
as
input
option,
you
can
only
select between noca and cal.With noca, only the previously set display value is taken over, and with
cal, the device takes over both the display value and the analogue input value.

5. Setting up the device
Menu level Parameterisation level
Setting
the
start/offset
value
of
the
measuring
range
ff
:
Setting
the
start/offset
value
of
the
measuring
range
,o
ff
s
:
Default: 0
Enter the start/offset value from the smallest to the highest digit [▲][▼] and confirm each digit
with
[P]
After
the
last
digit
the
display
switches
back
to
the
menu
level
If
Sens
F
was
selected
as
with
[P]
.
After
the
last
digit
the
display
switches
back
to
the
menu
level
.
If
Sens
.
F
was
selected
as
the input option, you can only select between noca and cal.With noca, only the previously set
display value is taken over, and with cal, the device takes over both the display value and the
analogue input value.
Setting the decimal point, dot:
Default: 0
The decimal point on the display can be moved with [▲][▼] and confirmed with [P].The
display then switches back to the menu level again.
Setting up the display time, SEC:
Default:
1
.0
The display time is set with [▲] [▼]. The display moves up in increments of 0.1 sec up to 1 sec
and in increments of 1.0 sec up to 10.0 sec. Confirm the selection by pressing the [P] button.
then
The display then switches back to the menu level again.
Rescaling the measuring input values, EndA:
Default: 10000
With
this
function
you
can
rescale
the
input
value
of
e
g
8
000
Hz
(works
setting)
without
With
this
function
,
you
can
rescale
the
input
value
of
e
.
g
.
8
.
000
Hz
(works
setting)
without
applying a measuring signal. If sensor calibration has been selected, these parameters are not
available.
Rescaling the measuring input values, OFFA:
Default: 0
19
With this function, you can rescale the input value of e.g. 100 Hz (works setting) without
applying a measuring signal. If sensor calibration has been selected, these parameters are not
available.

5. Setting up the device
Menu level Parameterisation level
Setting
of
the
impulse
delay
dELAY
:
Setting
of
the
impulse
delay
,
dELAY
:
Default: 0
With the impulse delay of 0 – 250 s (max), frequencies can be collected, which are even
smaller than by the predetermined measuring time of the device. If e.g. a delay of 250 seconds
is set
,
this means that the device waits u
p
to 250 seconds for an ed
g
e
,
before it assumes a 0
,
p
g,
Hz-frequency. Thus frequencies up to 0.004 Hz can be collected.
Adjustment of the optimum digital frequency filter, fi.frq:
Default: NO
If the optional filter is not activated by the adjustment „No“, frequences are ignored by the
adjusted frequency filter. Act on the assumption that the pulse-duty factor is 1:1. Accordingly
the minimal pulse duration is derived from the half of the time of oscillation. Use a filter of 10 Hz
or 20 Hz for contact bounce suppression.
Adjustment
of
the
pulse
-
duty
factor
at
activated
digital
filter,
fi
.
rat
:
Adjustment
of
the
pulse
duty
factor
at
activated
digital
filter,
fi
.
rat
:
Default: i‐i
Adjustment of the desired pulse-duty factor for pulse duration and pulse interruption. Like this, a
s
p
ecial
p
ulse behaviour can be ad
j
usted.
p
p
j
Setting up the tare/offset value, tArA:
Default: 0
The
given
value
is
added
to
the
linerarized
value
In
this
way
the
characteristic
line
can
be
The
given
value
is
added
to
the
linerarized
value
.
In
this
way
,
the
characteristic
line
can
be
shifted by the selected amount.
Number of additional setpoints, SPCt:
Default: 00
20
30 additional setpoints can be defined to the initial- and final value, so linear sensor values are
not linearised. Only activated setpoint parameters are displayed.