KODA iBass User manual

USER'S MANUAL
iBass
Music station For iPods
Please read the following instructions carefully before connecting, operating or
adjusting this product.
Please keep this manual in a convenient place for future reference.

CONTENTS
Contents………………………………………………………………………… 1
Important safety instructions………………………………………………… 1
Operation introduction………………………………………………………… 3
Getting started…………….………………………….…………………………4
Using the system………………………………..………………………………5
Troubleshooting……………………………………………………………7
Specifications…………………………………………………………………....9
IMPORTANT SAFETY INSTRUCTIONS
WARNING
To reduce the risk of fire or electrical shock, do not expose the product to rain or moisture.
WARNING
The apparatus should not be exposed to dripping or splashing, and objects filled with liquids.
Liquids can cause a failure and/or a fire hazard.
The lightning flash with arrowhead symbol, within an equilateral triangle, alerts the
user to the presence of un-insulated dangerous voltage within the system
enclosure that may be of sufficient magnitude to constitute a risk of electric shock.
The exclamation point within an equilateral triangle alerts the user to the presence
of important operating and maintenance instructions in this owner's guide.
WARNING
No naked flame sources, such as lighted candles, should be placed on the apparatus.
Note
This product is intended to be used only with the power supply provided.
Where the mains plug is used as the disconnect device, such disconnect device shall
remain readily operable.
This product must be used in doors, It is neither designed or tested for use outdoors,
in recreation vehicles, or on boats.
Directive 73/23/EEC.
This product conforms to the EMC directive 89/336/EEC and to the Low Voltage

GB-1

WARNING
Keep the remote control battery away from children since batteries are a choke
hazard. It may cause a fire or chemical burn if mishandled. Do not recharge,
disassemble, heat above 1000C(2120F), or incinerate.
Danger of explosion if battery is incorrectly replaced. Replace only with
Lithium Cell CR2025, Duracell, Eveready, Energizer, Maxell, Toshiba,
lithium battery. Please dispose of used batteries properly, following any
local regulations. Do not incinerate.
ImportantSafetyInstructions
1. Read these instructions - for all components before using this product.
2. Keep these instructions - for future reference.
3. Heed all warnings - on the product and in the owner's guide.
4. Follow all instructions.
5. Do not use this apparatus near water or moisture - Do not use this product near a
bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, near a swimming pool, or
anywhere else that water or moisture are present.
6. Clean only with a dry cloth - Unplug this product from the Electrical socket before
cleaning.
7. Do not block any ventilation openings. Install in accordance with the
manufacture's instructions - To ensure reliable operation of the product and to protect it
from overheating, put the product in a position and location that will not interfere with its
proper ventilation. For example, do not place the product on a bed, sofa, or similar surface
that may block the ventilation openings, Do not put it in a built-in system, such as a
bookcase or a cabinet that may keep air from flowing through its ventilation openings.
8. Do not install near any heat sources, such as radiators, heat registers, stoves or
other apparatus (including amplifiers) that produce heat.
9. Protect the power cord from being walked on or pinched, particularly at plugs, and
the point where they exit from the apparatus.
10. Only use attachments/accessories specified by the manufacturer.
11. Refer all servicing to qualified service personnel - Do not attempt to service this
product yourself. Opening or removing covers may expose you to dangerous voltages or
other hazards.
GB-2

12. Do not let objects or liquids enter the product - as they may touch dangerous
voltage points or short-out parts that could result in a fire or electric shock.
13. See product enclosure for safety related markings.
14. Use proper power sources - Plug the product into a proper power source, as
described in the operating instructions or as marked on the product.
Information about products that generate electrical noise
If applicable, this equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, this is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on , you are
encouraged to try to correct the interference by one or more of the following measures:
·Reorient or relocate the receiving antenna.
·Increase the separation between the equipment and receiver.
·Connect the equipment to an outlet on a different circuit than the one to which the receiver
is connected.
·Consult the dealer of an experienced radio/TV technician for help.
This product complies with the Canadian ICES-003 Class B specification.
OPERATION INTRODUCTION
Thanks for choosing the iBass Music Station. The iBass is designed specially to work with
your iPod. Just listen to it now!
BoxContent
Check the carton for the parts shown in Figure 1.
Place the iBass Music Station on a level surface. The speakers are shielded, which allows
the system to be placed near other video displays such as TVs or computer monitors.
GB-3
iBass
86(56 0$18$/
L%DVV
0XVLFVWDWLRQ )RU L3RGV

GettingStarted
Warning: Please do not connect your iBass music station’s power pack into a wall outlet
until all of your connections are made. Also, please turn off your iPod before docking on the
iBass Music Station.
Placing the correct bracket
To connect your iPod with the iBass music station, you will need to choose a correct iPod
bracket.
1. check the bottom of each bracket to identify the one that fits your iPod (Figure 2).
2. Place the selected bracket over the dock.
3. Press on both sides of the bracket to ensure it’s firmly placed (Figure 3).
You can remove and replace the brackets with any of the eight provided. This allows you to
use this system with iPodsof different sizes. To remove, gripthe inner part of the
bracket and take it out.
After choosing the appropriate bracket, you can dock your iPod to the iBass now.
Using 3.5mm headphone jack for connection
For new generation iPods, iPod shuffle, or other portable audio devices, connectionscan
be made using the 3.5mm headphone cable provided with the system. Connect one end
of the 3.5mm cable into the headphone jack at the back of the iBass ,and the other end to
the headphone or line out jack on your portable audio device. (Figure 4-3 and 4-4)
When the 3.5mm cable is used, the infrared remote cannot control your iPod functions and
the iPod will notbe recharged. For music playback, it is recommended that you adjust the
volume of your iPod or audio device to a sufficiently loud level, then adjust the volume of the
iBass to your desired level.
GB-4
*%9,'(2
*%9,'(2

Note
iBass will choose 3.5mm jack input as the priority signal source to play. while 3.5mm signal
source, and iPod is docked into iBass at the same time.
Connectingtothepower
After the iPod is docked, or headphone jack is connected with your audio device properly,
you can now insert the power pack into a wall outlet. (Figure 4-1 to Figure 4-4)
Checking your iPod compatibility
To ensure the infrared remote control to work as expected, your iPod must have the proper
or later iPod software version installed.
To check your iPod for the software version currently installed, select Settings, About,
Version on the iPod display, If upgrade is needed, please visit the website below and follow
the instructions there for a free download.
http://www.apple.com/ipod/download/
USINGTHESYSTEM
Your iBass is power on as soon as you plug it in. You should hear the music immediately. If
you do not, please refer to "Troubleshooting" on page 7.
The ƻ
+and Ϥ -buttons on either side of the dock is the master
volume control of the system. Press and hold ƻ
+or Ϥ -to
increase or decrease the volume.
iBass
iBass
Once your iPod is docked, power is recharged automatically until it’s fully charged.
To turn off your system totally, please remove your iPod from the dock, unplug the system
from the power supply.
to adjust the volume of iPod or your audio devices to a sufficiently loud level, then adjust the
volume of the iBass to your satisfactory level.
GB-5

Note
When earphone is plugged into your iPod, sound comes from both the earphone and the
system.
RemoteControlFunctions
To use the remote control, please ensure the battery is installed properly.
1. Press to turn off your system with LED off; press again turn on with LED on.
2. Press to mute the system; press again or turn volume control to resume.
3. Press to pause iPod playing; press again to play.
4. Press and to track forward and track back respectively. (Press and Hold for
rewind & fast forward)
5. Press and to adjust the master volume of the system.
6. Press and to adjust the treble volume.
7. Press and to adjust the bass volume.
8. Press to bypass the music signal; even you have tuned up your system by
adjusting its treble and bass.
MoreFunctions
1. AUTO MEMORY FUNCTION: iBass will store your volume and treble and bass setting
even it is power off; unless iBass is unplugged.
2. AUTO STANDBY: iBass will be automatically turned to Standby if the iBass is not in use
or no signal input for 2 minutes or above. Under STANDBY condition, Battery Recharge
function for iPod is still working if it is docked. It stops until it is totally charged. To
resume from STANDBY, press any button in remote control (except POWER).
Note
Your iPod navigation controls are fully functional when it is docked in the system except the
volume jog wheel. It is only functioned when the iPod is connected via the headphone jack.
Replacing remote control battery
Replace the battery when it stops working, or the control range is minimized.
Recommended to use a Lithium Cell CR2025 Duracell, Eveready, Energizer, Maxell,
Toshiba lithium battery. To replace, please follow the Figure 5.
Please note that the lighting of the room or battery life can affect the operating range of the
GB-6

remote control.
TROUBLESHOOTING
In case of malfunction, please power off the system immediately and check the unit
according to following table. If the problem still exists, please contact the dealer or the
manufacturer.
Symptom Problem Solution
iPod does not dock
properly
- Please ensure proper bracket is placed for your iPod.
(Refer to “Placing the correct bracket” on page 4.)
- Unplug the iPod from the docking station to see any
obstructions in the connector or in your iPod.
iPod / Audio
source is not
responding 3.5mm stereo cable
isn’t connected
properly
Connect 3.5mm stereo cable to the audio source. Make
sure the signal cable is inserted firmly into the correct jack
& is fully connected in the “line-out”, “audio-out”, or the
headphone jack on your sound card or other audio source.
Power cable is not
connected
- Make sure the iBass is plugged in and the LED is
illuminated.
- Press “Play / Pause” button on the remote control to go
into playback condition.
Power isn’t turned on
- Press POWER button on the remote control, if your iPod
indicator light is off, please repeat pressing POWER
button.
- Unplug the power cable for 1 minute, then plug it back to
reset the system.
Volume Level too low - The volume level might be too low, press “Volume+”
button to adjust.
No playable file on
iPod
- Make sure your iPod is on, and a track is selected for
playback.
Mute is on -iBass might be in MUTE condition. Press MUTE again.
No Sound
Software compatibility
problem
- Make sure your iPod is running with compatible software
(refer to "To check for iPod compatibility" on page 5).
- Remove your iPod and replace it after few minutes. You
may need to do this for few times.
GB-7
+

Your iPod is not
charging
- Make sure the power cable is securely plugged in to a
functioning wall socket. The symbol on the small
connector is matched with that on rear panel of the iBass .
Refer to Figure 4.4 on page 5.
- Make sure your iPod is firmly seated in the dock.
After quickly
undocking or docking
your iPod
- Remove your iPod from the dock, wait for 5 seconds,
and return it to the dock.
- Unplug the power cable for 1 minute, then plug it back to
reset the system.
iPod does not dock
properly.
- Remove your iPod from the dock, wait briefly, then
reset it. You may need to do this for few times.
Remote Control is not
pointed toward the
infra-red window
- Try the remote from different locations, and see if it
works. Strong lighting or other room conditions may cause
the problem.
- Make sure nothing blocks the infrared (IR) signal path
between the remote and your iBass.
- Wipe off the small red lens on the front end of the
remote.
Low batteries
- Check the remote control battery to make sure the + side
is facing up as shown in Figure 5 on page 7.
- Replace the remote control battery when low level.
Remote
Control is not
functioning
properly
Software compatibility - Upgrade software of your iPod. For details, refer to "To
check for iPod compatibility" on page 5
Volume level too high Press “Volume –“ button to decrease the volume.
Sound
distortion Sound source is
distorted
Distortion and noise are easily noticed with high-powered
speakers when playing poor quality audio source, esp.
WAV and MID files. Try a different audio source such as a
music CD or change better quality audio player.
System is not
Responding Mal-operation
- Unplug the power cable. After 1 min, plug it again to
reset the system
- Please contact customer service about this problem
GB-8
No Sound

SPECIFICATIONS
Notes
1) The specifications listed above are for reference only.
2) The technical specifications of this device are subject to changes without prior notice.
GB-9
O utput Power (THD10%) 15W×2
Speaker Unit 2.5”x2
Signal to Noise Ratio 80dB
Frequency Response 80Hz~20kHz
Rated Load Impedance 4ȍ
Power Rating 100-240V~50/60Hz, 0.5A
Power Consumption 40W
Product Dimension (H×W×D) 118×310×145 mm
Net Weight 750g

UMA0219E
Electronics Co . Ltd. All rights reserved.