Kodak ESP 5 Instruction Manual

Start Here
All-in-One Printer
Print
Copy
Scan
Note: A USB 2.0 (High Speed) cable is required to connect your Kodak All-in-One printer to your Windows
or Macintosh OS computer.

2www.kodak.com/go/aiosupport
10
ColorInk Car tridge
10
ColorInk Car tridge
Inkjet Printer Software
FOR WINDOWS & MACINTOSH
Power Cord and Adapter Printhead Ink Cartridges Software and
User Guide CD
Unpacking the Printer
1
a) Remove all orange shipping tape and any foam pieces
from the outside of the printer.
b) Lift the printer access door.
c) Remove all orange shipping tape and any foam
pieces from the inside of the printer.
d) Close the printer access door.
ColorInkCartridge
10
10
BlackInkCartridge
10
BlackInkCartridge
ColorInkCartridge
10
10
BlackInkCartridge
10
BlackInkCartridge
Carriage .
Printer access
door
.
Scanner lid .
Front access door .

3
www.kodak.com/go/aiosupport 3
a) 1. Connect the power cord and adapter.
2. Connect adapter to printer.
3. Connect to power source.
b) Remove the plastic film from the LCD display.
Position the LCD display.
c) Press ON . Select your language when prompted.
Do not insert paper until prompted by the
LCD display.
2Connecting the Power
Do not connect the USB cable to the printer until instructed during
software installation.
USB

4www.kodak.com/go/aiosupport
a) Lift the printer access door.
b) Remove the printhead from its bag.
Insert the printhead immediately upon
opening sealed bag. The printhead is fragile,
handle carefully.
c) Pull on the orange tab to remove the
protective retainer.
3Inserting the Printhead
ColorInkCartridge
10
10
BlackInkCartridge
10
BlackInkCartridge

5
www.kodak.com/go/aiosupport
d) Carefully remove and discard the orange
protective cap.
Do not touch the copper-colored contacts.
e) Place the printhead into the carriage.
Insert at the angle shown.
f) Push firmly against the target label of the printhead
until you hear a loud snap.
3
Carriage .

6www.kodak.com/go/aiosupport
a) Remove the black ink cartridge from its bag.
Insert ink cartridges immediately upon opening
sealed bag.
b) Carefully remove and discard the orange cap.
Handle ink cartridges carefully to avoid ink transfer.
c) Insert the black ink cartridge into the printhead.
10
10
10
Black Ink Cartridge
10
BlackInkCartridge
4Inserting the Ink Cartridges

7
www.kodak.com/go/aiosupport
d) Press down on the ink cartridge until you hear it click
into position.
e) Open and uncap the color ink cartridge. Insert it into
the printhead.
f) Press down firmly on the ink cartridge until you hear it
click into position.
g) Close the printer access door.
4
10
Cartouche d'encre noire
Cartouche d'encre couleur
10
ColorInkCartridge
10
10
BlackInkCartridge
10
BlackInkCartridge
ColorInkCartridge
10
10
Cartouche d'encre noire
10
10
Cartouche d'encre noire
10
Cartouched'encrecouleur

8www.kodak.com/go/aiosupport
a) Lower the front access door and pull the paper tray all
the way out.
If the attention light flashes, follow the instructions on
the LCD screen.
b) Insert a small stack of 5 to 10 sheets of plain paper
into the paper tray. Squeeze the paper edge guide and
slide it guide against the left edge of the paper.
Leave the paper tray extended.
NOTE: For photo paper, insert a stack of paper into the
paper tray face down.
Leave the paper tray extended.
5Loading Paper and Calibrating
Do not insert paper until the LCD display instructs you to do so.
Paper tray .
Front access
door
.
Paper edge guide

9
www.kodak.com/go/aiosupport
c) Flip up the paper stop.
d) Press Start.
The printer will automatically begin to calibrate.
e) Calibration will take about two minutes and is
complete when the sheet has printed.
5

10 www.kodak.com/go/aiosupport
WINDOWSWINDOWS
WINDOWSWINDOWS
WINDOWSWINDOWS
WINDOWSWINDOWS
WINDOWSWINDOWS
WINDOWSWINDOWS
WINDOWSWINDOWS
WINDOWSWINDOWS
WINDOWSWINDOWS
WINDOWSWINDOWS
WINDOWSWINDOWS
WINDOWSWINDOWS
WINDOWSWINDOWS
WINDOWSWINDOWS
WINDOWSWINDOWS
WINDOWSWINDOWS
a) Load the Kodak Inkjet Printer Software CD into the
CD-ROM drive. Follow the on-screen prompts
when the instructions appear.
If instructions do not appear, click Start, then Run.
Select CD-ROM drive and type setup.exe, then
press ENTER.
b) Connect the USB cable to the printer when
instructed. Continue to follow the on-screen
prompts until installation is complete.
FOR WINDOWS & MACINTOSH
6
Installing Windows Software
Do not connect the USB cable to
the printer until instructed during
software installation.
USB
Start Printers and Faxes
Right-click the icon for the printer you want to use as the default printer, and
then click Set As Default Printer.
Start Control Panel Hardware and Sound Printers
Right-click on the printer you want to use, and then click Set As Default Printer.
Setting your KODAK All-in-One Printer as the default on your WINDOWS OS
WINDOWS XP:
WINDOWS VISTA:
WINDOWS
6
Installing Windows Software