Kodak S510 - EASYSHARE Digital Picture Frame User manual

www.kodak.com/go/digitalframesupport i
ENGLISH
Back View
1 USB connector 7 Power
2 Memory card slot - SD, MMC, xD, MS 8 Play/Pause
3 DC-In (12 V) 9 Stop/Back
4 Remote control holder (removable) 10 Menu;
5 Slots for remote control holder Reset (press and hold 5 seconds)
6 Frame stand (to install, see page 3)11OK
12 Down
13 Up
1
2
3
Slide the remote control holder
into slots.
8137
5
4
6
10 11 12
9

Table of contents 1
ii www.kodak.com/go/easysharecenter
1 Getting started ......................................................................................1
Using the remote control...............................................................................1
Setting up your picture frame ........................................................................2
2 Doing more with your frame .................................................................6
Home screen—picture sources and settings...................................................6
Viewing your pictures....................................................................................7
Copying pictures ...........................................................................................8
Deleting pictures ...........................................................................................9
Selecting multiple pictures.............................................................................9
3 Changing frame settings .....................................................................11
Settings menus ...........................................................................................11
Upgrading your firmware.............................................................................12
Changing the frame orientation...................................................................13
4 Troubleshooting and support ..............................................................14
Picture frame problems ...............................................................................14
Screen messages.........................................................................................15
5 Appendix .............................................................................................17
Digital frame specifications..........................................................................17
Important safety instructions .......................................................................18
Additional care and maintenance ................................................................19
Limited warranty .........................................................................................19
FCC compliance and advisory ......................................................................21

www.kodak.com/go/digitalframesupport 1
1Getting started
Using the remote control
Button Press to:
power turn on/off the picture frame.
menu display the menu choices.
home return to the home screen.
back return to the previous screen.
stop a slide show, display thumbnails.
zoom magnify the picture.
OK accept the current selection.
4-way navigate through pictures or menus.
rotate rotate the picture, 90°clockwise each press.
select mark pictures for an operation.
stop stop a slide show, display thumbnails.
play/pause play or pause a slide show.
slide show play a slide show.
back
OK
menu
Remove the tab to
activate the remote

Getting started
2www.kodak.com/go/easysharecenter
Storing the remote control
1Install the remote control holder on the back of the
frame (page i).
2Slide the remote into the holder for convenient,
out-of-the-way storage.
Replacing the remote control battery
Setting up your picture frame
Buttons and controls
All buttons and controls described in this guide (for example: press ) are on the
remote control unless otherwise noted.
12
*release tab Push and hold the release
tab* while pulling the battery
holder out of the remote.
Follow the graphic on the
back of the remote control.
Replace with a CR2025, 3V lithium cell battery.

Getting started
www.kodak.com/go/digitalframesupport 3
Attaching the frame stand
1Place the square tab of the stand into the slot on the
back of the frame.
2Slide the tab into the slot until it’s secure.
NOTE: To change the orientation from landscape to portrait ,
see page 13.
Turning on the frame
CAUTION:
Do not use this power cable with other devices, including digital
cameras; the higher voltage (12 V) required by the frame will cause
serious damage to other devices.
■P
l
ug in t
h
e power ca
bl
e inc
l
u
d
e
d
wit
h
t
h
e
f
rame.
The frame turns on automatically. The language screen
appears the first time you power up your frame.
Your power cable may look different from the one pictured.
Use the plug that accommodates your type of power outlet.

Getting started
4www.kodak.com/go/easysharecenter
Setting your language
The first time you turn on your frame:
■Press to select your language, then press OK.
To change the language at a later time
■Press Home , Settings →Language. See
page 11.
Turning off the frame
■Standby mode—Press the power button on the
remote control or on the frame.
■Power off—unplug the power cable.
back
OK
menu

Getting started
www.kodak.com/go/digitalframesupport 5
Inserting a memory card
Connecting a digital camera or other USB device
Viewing your first slide show!
To play a slide show, insert a memory card, camera, or other USB device (see page 5).
The pictures are automatically displayed in the order they appear on the card or USB device.
MultiMedia Card
Secure Digital
Memory Stick
xD
Push the card firmly into the slot until it stops.
USB cable included with
your camera or purchased
separately.

6www.kodak.com/go/easysharecenter
2Doing more with your frame
Home screen—picture sources and settings
Go to the Home screen to access pictures from all connected sources and to change
frame settings.
1On the remote control, press Home .
All connected sources and the Settings icon are
displayed.
2Press to highlight a picture source, then:
■Press or to start a slide show.
OR
■Press OK to display thumbnails, folders, albums.
Home screen icons:
Memory card—appears when you insert a card (page 5). The label and icon
indicate the type of card.
Camera—appears when you connect a digital camera via USB cable (page 5).
USB drive—appears when you insert a USB flash drive (page 5).
Settings—customize and configure your frame. See Changing frame settings,
page 11.

Doing more with your frame
www.kodak.com/go/digitalframesupport 7
Viewing your pictures
Playing a slide show
There are three ways to start a slide show on your frame:
■Insert a memory card or USB device, then turn on the frame.
■Turn on the frame, then insert a card or connect a USB device—a new slide show
starts automatically, replacing a currently running slide show or single view picture.
■Select a picture in thumbnail view or select a picture source on the Home screen,
then press or .
Other slide show information
– A slide show plays continuously until you stop it or turn off the frame.
– You can change the slide duration and transition style (see page 12).
Viewing thumbnails
There are two ways to view your pictures as thumbnails:
■Press , select a picture source (see page 6), then
press OK.
OR
■Press or from a slide show or single view.
To navigate through the thumbnails, press .

Doing more with your frame
8www.kodak.com/go/easysharecenter
Viewing a single picture
■To view a single, full-screen picture, highlight it in thumbnails view and press OK.
■To magnify a picture up to 8X, press repeatedly. To view other parts of the
picture, press . To return to 1X size, press repeatedly.
■To rotate a picture, press .
Copying pictures
Copy pictures from your current picture source to any other connected device. For
example, copy pictures from a memory card to a USB flash drive.
1Select a picture to copy:
In thumbnails view, press to highlight a picture;
or, display a picture in single view.
2Press .
3Press to highlight Copy, then press OK.
4Press to highlight the source you want to copy to,
then press OK.
The picture is copied.
To copy multiple pictures, see page 9.

Doing more with your frame
www.kodak.com/go/digitalframesupport 9
Deleting pictures
1Select a picture to delete:
In thumbnails view, press to highlight a picture;
or, display a picture in single view.
2Press .
3Press to highlight Delete, then press OK.
4Highlight Delete and press OK again to confirm.
The picture is deleted.
To cancel the deletion, highlight Exit and press OK.
To delete multiple pictures, see page 9.
Selecting multiple pictures
Use the multi-select feature to copy or delete two or more pictures; or to play a slide
show of selected pictures.
Selecting one at a time
1In thumbnails view, press to highlight a picture; or, display a picture in single
view. Then press .
2Continue selecting pictures.
A check mark appears on the selected pictures.
Press again to remove a check mark.

Doing more with your frame
10 www.kodak.com/go/easysharecenter
Selecting/Unselecting all
Select all
1Press whenever pictures are displayed (slide
show, thumbnails view, single picture).
2Press to highlight Select all, then press OK.
A confirmation screen appears, then your picture display
reappears. A check mark is displayed on all pictures in
your current location.
Unselect all
1To remove all check marks, press , highlight
Select / Unselect all and press OK.
2Highlight Unselect all and press OK.
A confirmation screen appears, then your picture display
reappears. All check marks are removed.

www.kodak.com/go/digitalframesupport 11
3Changing frame settings
The Settings menu lets you customize and configure your frame.
1Press Home .
2Press to highlight Settings , then press OK.
3Press to select a setting. Follow the screen
directions. Press OK to accept your selections.
4Press to exit.
Settings menus
Setting Options
Upgrade firmware
This option is only
displayed if the upgrade file
(.img) is available on the
frame (memory card, flash
drive, etc.).
Upgrade firmware—load the latest version of firmware on your
frame (page 12).
Exit—return to the Home screen.

Changing frame settings
12 www.kodak.com/go/easysharecenter
Upgrading your firmware
Firmware is the software that runs on your frame. To check for the latest version, visit
www.kodak.com/go/digitalframedownloads. Follow the screen directions to download
the frame firmware and install it on your frame.
IMPORTANT:
Do not turn off the frame during the upgrade!
Viewing options Slide duration—specify how long each picture is displayed in a
slide show, from 3 seconds (default) to 1 hour.
Frame orientation—specify whether you wish to display your
frame in landscape (default) or portrait orientation.
Transitions—specify the transition style between pictures in a
slide show. See screen for options. The default is Random.
Screen Fit or Fill—Fit entire image . Show the entire
picture. Black borders may appear around the image. Fill the
screen (default). The picture fills the entire screen, some of
the picture may be cut off (cropped).
Brightness Press to adjust the screen brightness according to your
lighting conditions.
Language Choose your language.
About Check your frame model number and firmware version.
Setting Options

Changing frame settings
www.kodak.com/go/digitalframesupport 13
Changing the frame orientation
Your frame is set up to display pictures in landscape orientation . You can turn it to
portrait .
Change the stand position:
1R
emove the stand, turn it 90 ° , and replace as shown (see
page 3).
Change the setting:
1Press Home , Settings .
2Press to select Viewing options, then press OK.
Select Frame orientation, then press OK. Select
Portrait, then press OK.
3Press to exit.

14 www.kodak.com/go/easysharecenter
4Troubleshooting and support
For step-by-step product support, visit www.kodak.com/go/digitalframesupport and
select Interactive Troubleshooting & Repairs.
Picture frame problems
If... Try one or more of the following
Frame does not
turn on.
■Press the power button on the remote control or on the frame
(page 4).
■Make sure the power cable is securely connected (page 3).
■Make sure you are using the power cable that was included with
your frame.
Remote control does not
function.
■Check the battery in the remote (page 2).
Frame does not
recognize memory card.
■Purchase a certified SD, MS, xD, MMC card.
■Check the orientation of the card (page 5), then insert the card
firmly into the slot.
Frame freezes up. ■Unplug the power cable then plug it back in.
■Reset the frame: press and hold the Menu button on the frame
(not on the remote control) for 5 seconds (page i).
PIctures are not clear. ■Remove the protective film from the LCD screen.

Troubleshooting and support
www.kodak.com/go/digitalframesupport 15
Screen messages
Screen message Try one or more of the following
Create file failed. The device (memory card, USB drive, camera, etc.) you are
trying to copy to is protected.
■See your device documentation to remove write
protection.
■Insert or connect a different device.
Error attempting to open file or
directory.
■Turn off the frame, then turn it back on. If the problem
persists, contact customer support help at
www.kodak.com/go/digitalframesupport.
Error duplicate file name.
Error occurred while closing a file.
Error invalid file name.
Error reading from file.
Error writing from file.
Error writing a file.
Error writing to a file.
File Copy Failed!
Internal error.
Parameter is invalid.
Unknown error.

Troubleshooting and support
16 www.kodak.com/go/easysharecenter
Screen message Try one or more of the following
Unable to create file. Device write
protected or full.
The frame was unable to copy the picture.
■Insert a different card or device (page 5), or change
the picture source setting (page 6).
■Remove write protection, unlock card.
■If card is full, delete pictures from card.
Write failed. Select another
location.
The frame was unable to copy the picture.
■Insert a different card or device (page 5), or change
the picture location setting (page 6).

www.kodak.com/go/digitalframesupport 17
5Appendix
Digital frame specifications
For more specifications, visit www.kodak.com/go/digitalframesupport.
Kodak EasyShare S510 digital picture frame
Color display
14.2 cm (5.6 in.) diagonal analog LCD, 320 x 234 pixels, 4:3 aspect ratio,
11.4 x 8.5 cm (4.5 x 3.4 in.) viewable area
Battery, remote control
CR2025, 3V lithium cell, included
Internal storage capacity
No
Power
110V AC 60Hz (US), 100-240V AC 50-60Hz (WW), 12V DC adapter
USB connection
USB 2.0
Other features
Picture format JPEG
Memory cards Secure Digital, Memory Stick, xD, MultiMedia Card

Appendix
18 www.kodak.com/go/easysharecenter
Important safety instructions
CAUTION:
Do not disassemble this product; there are no user-serviceable parts inside. Refer
servicing to qualified service personnel. Do not expose this product to liquid,
moisture, or extreme temperatures. The use of controls, adjustments, or procedures
other than those specified herein may result in exposure to shock and/or electrical or
mechanical hazards. If the LCD breaks, do not touch the glass or liquid. Contact Kodak
customer support.
■The use of an accessory that is not recommended by Kodak may cause fire, electric shock, or injury. For
approved accessories, visit www.kodak/go/accessories.
■When removing the battery from the remote, allow it to cool; it may be hot.
■Follow all warnings and instructions supplied by the battery manufacturer.
■Use only batteries approved for this product to avoid risk of explosion.
■Keep batteries out of the reach of children.
■Do not allow batteries to touch metal objects, including coins. Otherwise, a battery may short circuit,
discharge energy, become hot, or leak.
■Do not disassemble, install backward, or expose batteries to liquid, moisture, fire, or extreme temperature.
Temperature Operating: -4 to 140°F (-20 to 60°C)
Storage: -22 to 185°F (-30 to 85°C)
Size 19 x 15.6 x 2.5 cm (7.5 x 6.125 x 1 in.)
Kodak EasyShare S510 digital picture frame