Kody Technologies 101-017 User manual

Kody Technologies LLC
Bike Rack Light –Saris SuperClamp
Kody Technologies LLC www.kodytechnologies.com
Protect Your Ride Davis CA, 95618
Congratulations on your purchase and thank you for
your commitment to road safety for your bikes,
friends, family, and those around you. Read and
follow this instruction guide to install your new Kody
Bike Rack Light.
Disclaimer
Tail, Brake and Turn signal lights are a critical safety
feature during the operation of your vehicle. Rack
lights increase your vehicle’s visibility when the lights
are obstructed by a bike rack, or any other device
mounted to the rear of the vehicle. Please read and
review all information carefully before installation.
Install the light per the instructions and verify
functionality on a regular basis. If you have any
questions or concerns, please contact us at Kody
Technologies.
•Always verify cable routing and connection and
test light function prior to driving, using the light
and relying on it for your safety.
•This light adds four pounds to the load on your
bike rack. Check rack manufacturer’s manual to
verify the total load on the rack does not exceed
any limits.
•Rack lights improve your visibility and signal
communication on the road. They are not a
substitute for driving safely and following all traffic
laws.
•Kody assumes no liability for injury to persons,
damage to movable or immovable property, loss
of profit, or any other loss or damage caused by
the improper mounting or use of the carrier,
including but not limited to mounting or use in
conflict with the assembly instructions, mounting
instructions or any other instructions given, in
writing or verbally, by Kody.
Kody Technologies LLC does not assume any
responsibility or liability for accidents or injuries
resulting during use of this product or misuse of this
product.
Product Warranty
We've designed an extremely rugged rack light and
are proud to provide a 1-year warranty on any failure
on the electronics or hardware. If you experience any
issues with your light please contact us, return it and
we'll ship you a replacement.
Return Policy
If you are not 100% satisfied with the rack light, please
contact us to let us know. We offer a 30-day hassle-
free return policy. Return the light assembly in like-
new condition and we'll ship you a replacement or
refund your money. Most importantly we want to
understand any issues you experience so we can
address them, and we can continuously improve our
products.
Any questions, ideas, or concerns? Please contact us
at [e-mail]

Kody Technologies LLC
Bike Rack Light –Saris SuperClamp
Kody Technologies LLC www.kodytechnologies.com
Protect Your Ride Davis CA, 95618
Installation Instruction
Model#: 101-017
The rack light installs at the back of the rack using
existing hardware locations with new longer screws.
It fits cleanly and does not affect any tray
adjustment or bike loading.
Tools: 8mm Allen Wrench and Ratchet with 17mm
socket or 17mm box end wrench
1. Remove the two screws and nuts holding the
last set of bike trays in place. Be careful, once
the screws are removed the bike rack comes
apart.
2. Hold the rack frame together and the light
bracket in place and run the longer screws
through the light bracket and the Saris bike
rack frame members. Install the nut on
screws and tighten the hardware.
3. Route cable along length of rack to vehicle
connection and use cable ties to secure the
cable to the rack frame. Bike racks have many
pivot points. Be sure to route the cable away
from and around pivots to keep them from
getting pinched.
4. Connect the light to your vehicle’s trailer
connection and test all light functions (tail,
brake, hazard, left and right-hand turn
signals).
5. If turn signals don’t function correctly on your
vehicle, please see the “How to” page on our
website for LED Trailer Lights or contact us.
Any questions, ideas, or concerns? Please contact
us at [email protected]
Remove
Two
Existing
Screws
& Nuts
Set Bracket and Install hardware
Routed cable
along rack and
test the light.