Kogan KABNKNTCNTA User manual

NOTE COUNTER
KABNKNTCNTA

Connect the machine to the power supply
Connect the power cord to a wall outlet or power supply (AC 220V ±10%, 50Hz). Note that
this device must be operated under the required voltage and frequency.
Prepare the device
Ensure the device is set up on a secure, durable and level surface. Inclinations may lead to
counting errors.
Set the position of the note guide to be 2mm-to-3mm longer than the banknotes being
counted.
Verifying and adjustment of the Hopper Plate
The Hopper Plate ensures proper feeding of the banknotes for counting. It is secured to the
back of the device with two pivoting points and a magnetic lock.
To verify that the hopper plate is properly adjusted, press or lift the hopper plate and look for
any displacement (see the figure). If any displacement occurs, press or lift the hopper until
the magnetic lock holds the piece in place.
Adjust a proper gap between hopper and feeding roller by turning the adjustment screw (Fig
1). Turn it left to decrease the space and turn right to increase it.
Fig 1
BEFORE FIRST USE

Preparing the banknotes
Before starting to count the banknotes, please check whether there are clips, staples, elastic
bands or coins in the banknotes. Remove all of these, as they may jam the device or result in
counting errors.
Clips
Staples
Elastic bands
Coins
Check for any wet, sticky or very dirty banknotes. Do not count these.
Check for any deformed, folded or badly damaged banknotes. Do not place these notes on
the feeding desk.
Deformed
Folded
Broken
To avoid jamming or counting errors, ensure the notes are neatly arranged and on an even
level before counting.
Before inserting, twist the stack of notes to create an even slope (Fig 2). Loosen and pat the
stack before placing onto the feeding tray. Figures 3 and 4 demonstrate incorrect procedure.
Fig 2
Fig 3
Fig 4

Control panel overview:
Basic operation:
Switch from Auto Mode to Manual Mode
•Upon start up, the device with begin in Auto mode as default.
•To switch to Manual mode, press and hold the 'RESTART' button for 3 seconds
until the display screen reads ‘ N O ’. Press the 'RESTART' button again to confirm
and save.
Ultraviolet Detection
•To turn on Ultraviolet Detection, press the ‘UV’ button until the UV light turns on.
•To t u r n Ultraviolet Detection off, simply press the ‘UV’ button once again. The light
will turn off.
Magnetic Detection
•To turn on Magnetic Detection, press the ‘MG’ button until the MG light turns on.
•To t u r n Magnetic Detection off, simply press the ‘MG’ button once again. The light
will turn off.
OPERATION

Addition Mode
•In Addition mode new inputs are added to the total counted, not resetting with
each new input.
•To turn on Addition mode, press the ‘ADD’ button until the Addition light turns on.
•To t u r n Addition mode off, simply press the ‘ADD’ button once again. The light will
turn off.
Batching mode
•In batching mode the counter can sort money together into pre-set values.
•Press the 'BATCH' button on the device, the display will show 100 / 50 / 20 / 10.
•For the latest Australian currency notes, ensure the transparent strip in the middle
of the note (Fig 5) does not pass through the IR sensors of the unit (Fig 6), as this
may cause the device to display error codes or an inaccurate note count.
Fig 5
Fig 6
Advanced operation:
Fake Note Counting
•To turn Fake Note Counting on, hold the Decrease (–) button for at least 3 seconds
until the display screen shows 'U-01 '.
•To t u r n i t off again, briefly press the Decrease (–) button again until the display
screen shows U-00.
•Let the device run to save your changes.
Double Note Recognition
•Double-note recognition alerts when two bills have been fed simultaneously.
•To increase the sensitivity in detecting double-notes, hold the 'BATCH' button for at
least 3 seconds until the display screen shows ‘E’ followed by a number (ie, ‘E-05’).
•The default sensitivity setting is E-05, however this can be adjusted by pressing the
Increase (+) button or Decrease (–) button. The total range is E-00 to E-20. A higher
number represents higher sensitivity for double-note detection.
•Press the 'RESTART' button to save your changes.
IR Sensors

Chained Note Recognition
•Chained-note recognition alerts when a leading bill has pulled in a trailing bull
prematurely.
•To increase the sensitivity in detecting chained-notes, hold the ‘ADD' button for at
least 3 seconds until the display screen shows ‘C’ followed by a number (ie, ‘C-05’).
•The default sensitivity setting is C-05, however this can be adjusted by pressing the
Increase (+) button or Decrease (–) button. The total range is C-00 to C-10. A higher
number represents higher sensitivity for chained-note detection.
•Press the 'RESTART' button to save your changes.
Ultraviolet Sensitivity
•The ultraviolet light sensitivity helps detect fake paper and plastic notes with
fluorescence.
•To increase the sensitivity in detecting abnormalities, hold the ‘UV’ button for at
least 3 seconds until the display screen shows ‘A’ followed by a number (ie, ‘A-10’).
•The default sensitivity setting is A-10, however this can be adjusted by pressing the
Increase (+) button or Decrease (–) button. The total range is A-00 to A-20. A higher
number represents higher sensitivity for detecting fake notes and plastic notes with
fluorescence.
•Press the 'RESTART' button to save your changes.
Magnetic Sensitivity
•The magnetic sensitivity helps detect fake paper and plastic notes with magnetic
components.
•To increase the sensitivity in detecting abnormalities, hold the ‘MG’ button for at
least 3 seconds until the display screen shows ‘B’ followed by a number (ie, ‘B-05’).
•The default sensitivity setting is B-05, however this can be adjusted by pressing the
Increase (+) button or Decrease (–) button. The total range is B-00 to B-20. A higher
number represents higher sensitivity for fake paper and plastic notes with magnetic
components.
•Press the 'RESTART' button to save your changes.
Factory Reset
•To perform a factory reset, first turn off the device, then hold the Increase (+) and
Restart buttons simultaneously for at least 3 seconds until the display screen
shows:
•Now turn the device on. The factory reset will be complete.

Rated voltage/Frequency AC 220V±10%, 60Hz
Rated current 350mA (Max)
Power consumption 75W (Max)
Counting speed >1000pcs/min
Feeding system Roller Friction Type
SPECIFICATIONS

Self-test Codes
Self-code
Reason
FE1
Start Sensor
FE2
Left Counting Sensor
FE3
Right Counting Sensor
FE6
Clear Sensor
FE7
Disc Code sensor
FEA
UV
Error Codes
Code
Reason
A
UV
b
MG
C
Chain Note
E
Double Note
H Half Note/Cross Note
TROUBLESHOOTING

NOTES

Need more information?
We hope that this user guide has given you
the assistance needed for a simple set-up.
For the most up-to-date guide for your product,
as well as any additional assistance you may require,
head online to help.kogan.com