Kogan KAS8C4W1TBB User manual

8 CHANNEL 1080P 1TB
SECURITY SYSTEM
(WITH 4 WIRELESS CAMERAS)
KAS8C4W1TBB

NVR
1
Wi-Fi Antenna Port
2
WAN Port (video in)
3
VGA Port
4
HDMI Port
5
USB Port
6
Power Input (DC 12V 2A)
OVERVIEW
①
④
①
③
⑥
⑤
②
7

Camera
1
Antenna
2
Camera Mount
3
Lens & Sensors
4
Ethernet Port (RJ-45)
5
Power Input (DC 12V 2A)
①
④
③
⑤
②

System Overview
Notes:
• Camera connection to NVR is wireless: the NVR connection to the router is wired.
• It is recommended to place the NVR in the centre of the monitoring area and to
avoid obstacles between the cameras and NVR as much as possible.
Power adapter
IP
Camera
Display device
VGA Output
NVR
Mouse
Router
Video in
USB Interface
INSTALLATION
Power
adapter

Adding Camera
The supplied cameras are matched at the factory. Re-adding or adding an additional
camera can be done in the Video Management settings on the NVR using either “auto add”
(cameras will be detected automatically) or “match code”.
Cameras’ antennas should be positioned parallel to the Wi-Fi signal transmission and not
angled directly at the router.
The cameras can also be set up with a wired network connection.
Correct
Incorrect
NVR
Router
Power
adapter
Power adapter
Power
adapter
Power
adapter

System Setup
The system is a standalone unit with an embedded Linux operating system in the NVR. To
configure the operating system, connect a keyboard, mouse and monitor with HDMI or VGA
input.
1. Install antennas for cameras and NVR.
2. Connect a monitor via HDMI or VGA.
3. Connect the NVR to power (use the larger 12V 2A power adaptor).
4. Connect the cameras to power (use the smaller 12V 1A power adaptors).
5. The camera feed will display within a few seconds.
6. Connect the included USB mouse to a USB port on the rear of the unit.
Hard Drive Replacement
• Unplug NVR, unscrew & remove top
cover.
• Remove HDD.
Connect SATA power + data cables from
NVR to new HDD.
Keep HDD in position and screw in holes
from underneath the NVR to secure it in
place.
Replace top cover.

Mouse Function
Button
Action
Effect
Function
Left
Single click
Select
Option button, drop down menu, list,
check box, radio button
Double click
Window zoom
1. Switch between single and multi-
interface in preview
2. Add device
Drag
Set the area
1. Set motion detection area
2. Select electronic amplification area
Middle
Scroll
Change the
content
1. Change contents of the drop-down
box
2. In zoom preview, switch channel
interface orderly
Right
Single click
Log out
1. Close interface
2. Show shortcut menu in main
interface
OPERATION

Right click to access the following options:
• Split screen: single/multiple camera live feed
• Video management: manage IP & NVR channels
• System setup: change system settings
• Video playback: play back recordings
• Video backup: back up recordings
• Colours adjust:adjust image settings
• PTZ control: adjust PTZ settings (on supported cameras)
• Manual record: change recording settings
• Volume: change audio settings (on supported cameras)
• Setup Wizard: step-by-step initial setup guide
• Fast network: change network settings
• Exit System: logout, reboot, close display output and shut down system
FUNCTIONS

Recording Video
• Timed Recording: Right click System Setup > Record Setup > Record Plan. You can set
a schedule to record. The default mode is 24/7.
• Manual Recording: Right click Manual Record. Individual channels can be
enabled/disabled.
• Motion Recording: Right click System Setup > Record Setup > Record Plan. Deselect
Time and select Motion; the camera will only record when it detects motion.
Playback
Right click Video Playback > Manual Search. You can search by channel and time and
click Playback to view recorded videos.
Backup
• Connect a USB drive to a USB port on the device.
• Right click Video Backup > Choose Backup Channel > Choose Video Mode > Setup
Searching Time > Search. Choose the video file to back up.
• Supported drive size is up to 32GB and supported recording is up to 1 hour.
Login / Logout
• Right-click on the shortcut menu and click the user to log off.
• To set a logout automatically, you can set this in system > general settings. The system
will automatically log off the system in 1 minute. Username and password will need to
be re-entered when next using the system.
Restart & Shut Down
• To restart the machine during use, right-click the shortcut menu and select “exit
system”: click to complete the restart.
• To shut the machine down, right-click the shortcut menu and select the shutdown
option.

Local Viewing
With the PC and the NVR connected to the same Local Area Network (LAN),
1. Find the IP address and port number of the NVR (through System Setup >
Network Setup).
2. Enter the IP address in the browser (e.g., http://192.1.17). If the default port number
has changed from 80, enter the port number as well in the format (e.g., if the port
number was changed to 100 e.g., http://192.1.1.100)
Remote Viewing
1. Navigate to http://e-seenet.com in a browser.
2. Input Device ID, username and password to log in.

Device ID is shown at the right bottom corner of the monitor. The status should show as
“online”. The default username is admin and the default password is empty.
Mobile Access
1. Download the IP PRO app from the App Store, Play Store or by scanning the QR
code below.
2.
o Add the NVE through the device ID, username and password.
o Device ID is shown at the right bottom corner of the monitor. The status
should show as “online”. The default username is admin and the default
password is empty.
o Live playback is supported within the app. Due to network conditions and
connection speed, playback over LAN will be more reliable and consistent
than playback from mobile data.

A wireless network is inherently susceptible to range limitations and interference from
obstacles, etc. To improve the reliability and stability of a Wi-Fi connection, refer to the
following setup tips and configuration options.
Antenna Extension
Repeater Setup
In the repeater setup page, first set up and connect any IP Camera to the NVR. This
function increases the wireless transmission distance and extends the total range of
wireless kit.
1. Right click and select Video Management > Repeater.
2. Add repeater: as below, click the icon and a channel besides the currently one
being copied from (channel 3 in this example).
EXTENDING WIFI RANGE
Antenna Extension Cord
IP Camera
Wall
Window
NVR

3. As below, IPC1 is connected to the NVR through IPC2 and IPC3. IPC2 is connected
to NVR through IPC3. IPC3 is connected to NVR directly.
4. Click Apply > Refresh to confirm the setup is successful.

NOTES

Need more information?
We hope that this user guide has given you
the assistance needed for a simple set-up.
For the most up-to-date guide for your product,
as well as any additional assistance you may require,
head online to help.kogan.com