Kogan VIPER-X 2 DRONE User manual

VIPER-X 2 DRONE
WITH 1080P CAMERA AND VR HEADSET
KAVIP2DRONA

2
Safety & Warnings
3
Components
5
Overview
6
Installation
8
Operation
12
App Installation
19
Cleaning & Care
22
Notes
23

3
Read all instructions in this guide before using this product. Retain this guide for future
reference. Do not skip, substitute or modify any steps or procedures in this guide, doing so
may result in personal injury or product damage.
Important notes
• Do not attempt to touch the drone whilst it is operating under any circumstances.
• This product is not a toy and can be dangerous when used incorrectly. Follow all
instructions while operating. Disassembling or modifying the drone arbitrarily, operating
improperly, or being unfamiliar with this product may lead to an accident and possible
injuries.
• This product is intended for use by persons aged 14 years or older. It is recommended
that people between 14-18 years operate the drone under supervision.
• Ensure the product is operated in a safe environment.
• It is recommended that you seek the assistance of an experienced drone pilot before
attempting to fly the drone for the first time. A local expert is the best way to properly
assemble, setup, and fly your drone for the first time. It requires a certain degree of skill
to operate and is subject to normal wear and tear.
Safety notes
• Always operate the drone in a safe environment. Do not operate drones within the
vicinity of people.
• Drones are prone to accidents and failures when piloted incorrectly. Operators are
responsible for their actions as well as any damage or injury caused by pilot error and
radio interference.
• This product is suitable for indoor and outdoor use. Always fly in a place clear of
obstacles and keep a safe distance from people and pets.
• Do not operate the drone in unsafe conditions and keep clear of heat sources, wires, or
electric power sources.
• This product contains precision electrical components. Always keep this product away
from water and other liquids. Exposure to water or moisture in any form can cause this
product to malfunction resulting in a crash.
• To avoid a potential fire hazard, do not short, reverse the polarity, or puncture batteries.
Buttery charging must be done under supervision and in a location out of reach of
children.
SAFETY & WARNINGS

4
• Ensure that the orientation of the batteries is installed correctly based on polarity, as
indicated in the battery compartment. Do not mix batteries of different
chemistry/specification.
• Remove the batteries if you are not going to use this product for an extended period.
Always dispose of old batteries according to your local environmental authority.
• Li-Polymer batteries pose higher operational risks compared to other battery types; thus
it is imperative to follow its usage instructions.
• Avoid contact between the battery and metallic objects.
• If there is an increase in battery temperature after operation, cease use immediately
and allow it to cool down. Continuous use of this battery may cause it to expand,
deform, explode, or result in potential fire hazards.
• Drones are not to be flown within 5km of airports. Many locations are considered no fly
zones and you must ensure that you fly in areas that align with your local laws and
ordinances.
• Do not place heavy objects directly onto the drone or any of its components.
VR headset
• Do not use the VR headset while the phone is charging.
• During use, if you feel dizzy or sick, take a break before continuing operation.
• Pregnant women, people with high blood-pressure, and people with a fear of heights
should not use the VR headset.

5
Upper Body
Lower Body
Propellers (x4)
Protecting Frames (x4)
Landing Skids (x2)
Motor (x4)
LED Lights (x2)
Receiver Board
Battery
USB Charging
Cable
Phone Holder
Controller
Camera
COMPONENTS

6
Controller
Photo
Video
Left Control
lever
Accelerator
Antenna
Power
switch
Headless
flight
Return
Speed trim
Speed/gear
Roll
Right Control
lever
Crab
trim/fine
tuning
Forward/
backward fine
tuning
Indicator
OVERVIEW

7
VR headset
1
Focus slider
Adjusts the focal distance
2
IPD slider
Adjusts Inter-pupillary distance (IPD)
3
Left headphone jack
Left hand side headphone input
4
Sliding panel
Slides to expose the phone’s camera
5
Phone holder
Open to insert phone into headset
6
Right headphone jack
Right hand side headphone input

8
Controller battery installation
• Remove the battery compartment cover.
• Install x4 AA batteries (not included) into the battery compartment. Pay attention to
the orientation of the polarity symbols.
Drone
• Install the two landing skids on the underside of the drone (Figure 1).
• Attach the protecting frame onto each corner of the drone and secure it in place using
the screws (Figure 2).
Figure 1
Figure 2
x4 AA Batteries
INSTALLATION

9
Phone holder installation
• Attach the phone holder to the controller in the position shown (Figure 3).
• Secure the phone in place using the screw (Figure 4).
Figure 3
Figure 4
To avoid accidentally engaging the buttons on your mobile phone, you can install the
supplied rubber pads onto the phone holder.
Attach the rubber pads to the phone holder according to the position of your phone
buttons. (Figure 5)
Figure 5
Rubber pad
Phone buttons
Screw hole

10
VR headset
• Download the "Veer VR" app from the Play Store (Android) or App Store (iOS).
• In the “Veer VR” app settings, switch to the side-by-side mode.
• Slide open the phone holder and insert the phone into the VR headset.
Step 1:
• Launch the "Veer VR" app and follow the in-app prompts to connect to the drone's
camera.
• Ensure the app is running in split-screen mode (side-by-side mode).
Step 2:
• Insert your phone into the VR headset.
• Align the middle line on the phone with the middle of the VR headset.
• Adjust the IPD and focus sliders.

11
Step 3:
Control the viewing angle by moving your head.

12
Charging the drone battery
• Place the drone's power switch in the OFF position and then open the battery
compartment.
• Disconnect the battery wire from the power port.
• Connect the battery wire to the USB charging cable and plug it into a USB power
adapter (mobile phone charger). Ensure the cable is plugged in firmly and in the correct
orientation.
• Charging time is approximately 70-90 minutes.
• Once the battery is fully charged, reconnect the battery wire to the power port and
close the battery compartment.
OPERATION

13
Turning on the drone
• Slide the power switch on the controller and the drone to the ON position.
• Push the Left control lever (throttle) up to the highest position and then pull it back to
the lowest position. The controller will emit a sound, indicating that the drone is ready
to fly.
Flying the drone
Push the left control lever left or right to rotate the drone in the respective direction.
Turn Left and Right

14
Push the right control lever left or right to fly the drone in the respective direction.
Sideward Fly
The forward/backward buttons can be used to the fine tune the direction of the drone.
Forward/Backward fine-tuning
Press the crab trim buttons to fine tune the drone flight left and right.
Sideward Fly fine-tuning

15
Acrobatic flight:
When you are confident with the basic operation and controls, you can attempt tricks and
stunts. Fly the aircraft to a height of more than 3 meters. Press the roll button on the
controller, then push the right control lever (in any direction) to perform a 360° flip.
Headless flight mode
Press the headless flight mode button to enable headless mode. The indicator will begin
flashing slowly. In this mode, the drone will override its front and rear azimuths and
reposition the front and rear using the controller as a reference point. For example, when
the right control lever is pushed forward, the drone will fly away from the controller; when
the right control lever to pull back, the drone will fly towards the controller (camera front
side).
Pressing the headless flight mode button again will disable the headless flight mode.
3 meters
Roll
Speed gear
Note:
When the drone is used with the camera, acrobatics will not be possible.

16
Return key:
• If the drone leaves your field of view, press the return key. The drone will fly backwards
to the controller.
• When the drone comes back into your field of view, touching the right lever will cancel
this function.
Camera
• Connect the 3-pin connector from the camera to the drone.
• Place the drone's power switch in the ON position. The indicator will turn solid green if
the camera has successfully connected and operating normally.
Capturing photos and video:
• Press the photo button, then the camera will capture a photo. The controller will emit a
beep and the green indicator on the camera will turn red and begin flashing.
• To capture video, press the video button and the camera will begin recording. The
controller will emit a beep and the green indicator on the camera will turn red and
begin flashing.
• Pressing the video button again will stop the recording. The controller will emit a beep
and the camera indicator will turn solid green.

17
Low battery protection
When the drone's battery is low, the indicator will flash, and the rotors will slow down and
stop.
Over-current protection
If the drone's propellers become jammed, the control system will stop supplying power to
the rotors automatically. Cease use and turn off the drone and controller. Inspect the
propellers and replace/repair is necessary.
Factory reset
In the event the drone displays unusual flight characteristics, you can reset it back to factory
default settings by following the steps below:
Step 1:
Slide the power switch on the controller and the drone to the ON position.
Step 2:
When the drone's indicator changes from flashing rapidly to flashing slowly, push the left
control (throttle) lever to the highest position and then pull it back to the lowest position.
The indicator will then change from flashing slowly to a solid light.
ON

18
Step 3:
Place the drone on a horizontal, flat surface, then push both left and right control levers to
the bottom right corner for approximately 2-3 seconds. The indicator will change from solid
to flashing rapidly. After 2-3 seconds, the indicator will change to solid, and the drone has
been successfully reset.

19
Apart from the controller, the drone can also be controlled through using the “VS FPV” app.
1. Installing the VS FPV app to your mobile phone
Please scan the below QR code to download the app according to your phone’s
operating system.
iOS
Android
2. Connecting
• Turn on the drone.
• Enter the Wi-Fi settings of your phone and search for the Wi-Fi
network,
"VS FPV _***" and connect.
3. Opening and using the app
• Open the “VS FPV” app, then
tap “Connect”.
APP INSTALLATION

20
• Press the “Off” icon followed by the “Altitude hold” icon to reveal more functions and
movement controls.
1
Back
15
Flight planning
2
Photo
16
Left sideways tuning
3
Video
17
Forward
4
Gallery
18
Precise control of going forwards
5
Speed control (30%, 60%, 100%)
19
Right sideways
6
Altitude hold
20
Left sideways
7
Gravity control
21
Precise control of going backwards
8
Show/Hide movement controls
22
One tap landing
9
Settings
23
Precise control of doing left
flips/rolls
10
360° flips and rolls
24
Precise control of doing right
flips/rolls
11
Accelerate
25
Emergency stop
12
Left flip/roll
26
Precise control of going left
sideways
13
Music
27
Precise control of going right
sideways
14
Right flip/roll