Kogan KAWLMFM90MA User manual

KOGAN TILT EXTENDABLE FULL
MOTION HEAVY DUTY WALL MOUNT
(SUITABLE FOR 37” – 90” TVS)
KAWLMFM90MA

Read the entire instruction manual before you start installation and assembly. If you have
any questions regarding any of the instructions or warnings, contact your local distributor for
assistance.
CAUTION: Use with products heavier than the rated weights indicated may result in
instability causing possible injury.
•Please closely follow the assembly instructions. Improper installation may result in
damage or serious personal injury.
•Safety gear and proper tools must be used. This product should only be installed by
professionals.
•This product is designed to be installed on solid concrete walls, masonry walls or wood
stud walls.
•Make sure that the supporting surface will safely support the combined weight of the
equipment and all attached hardware and components.
•Use the mounting screws provided and DO NOT OVER TIGHTEN mounting screws.
•This product contains small items that could be a choking hazard if swallowed. Keep
these items away from children.
•This product is intended for indoor use only. Using this product outdoors could lead to
product failure and personal injury.
•Never exceed the maximum load capacity of 75kg or it may result in product failure or
personal injury.
IMPORTANT: Ensure that you have received all parts according to the component checklist
prior to installation. If any parts are missing or faulty, contact your place of purchase for a
replacement.
MAINTENANCE: Check that the product is secure and safe to use at regular intervals (at
least every three months).
SAFETY & WARNINGS

AWall mount assembly (x1)
BTV brackets (x2)
CStencil (x1)
DLocking bolt (x2)
ESpanner (x1)
FSpirit level (x1)
M-A Screw
M5 x 14 (x4)
M-B Screw
M6 x 14 (x4)
M-C Screw
M6 x 30 (x4)
M-D Screw
M8 x 30 (x4)
M-E Screw
M8 x 50 (x4) M-F (x4) M-G Spacer (x4) M-H Spacer (x4)
W-A Screw
ST8.0 x 90 (x6)
W-B Wall anchor
ø12 x 60 (x6)
W-C Washer
(x6)
Tools required for installation (not supplied)
Phillips head
screwdriver Stud finder Pencil Drill Wrench
COMPONENTS

Step 1
Using a pencil and spirit level, mark the desired position for the mount on your wall, using the
stencil (C) for the hole positions. If mounting on dry wall or plaster-board, use a stud finder
first to check positions of wall studs and ensure the position is free from electrical wiring.
Using a drill, create the pilot holes.
Drywall / plaster: Use a ø6mm or 1/4” drill bit, drilling 90mm deep – 4 holes
Masonry / concrete:Use a ø12mm or 1/2” drill bit, drilling 95mm deep – 6 holes
When using spirit level, ensure the bubble is centred as per the image
shown here.
Pencil, stud finder and drill not supplied.
INSTALLING MOUNT TO WALL

Step 2
Drywall / plaster: Insert the top two screws (W-A), ensuring a 5mm excess is left between
the head of the screw and the wall surface. Do not use wall anchors.
Masonry / concrete:Insert wall anchors (W-B) into all six drilled holes. Insert the outer top
two screws (W-A), ensuring a 5mm excess is left between the head of the screw and the wall
surface.

Step 3
Lift the wall mount assembly (A) and hook onto the top two screws.
Step 4
Drywall / plaster: Secure to the wall using washers (W-C) and screws (W-A) in the bottom
two holes. Do not use the wall anchors.
Masonry / concrete:Secure to the wall using washers (W-C) and ST6.3 screws (W-A) in
remaining four holes.

Align the brackets with your TV’s VESA holes and secure using supplied screws (“M-” set)
and spacer (M-F) depending on required length.
Check if additional spacers (M-G, M-H) are required to ensure correct length of screw, as per
the below image. Failure to follow this step may result in damage to your TV or wall mount.
INSTALLING BRACKET TO TV

Hook the TV with brackets installed onto the wall mount. Two people should carry the TV to
prevent damage.
Once in place, secure the brackets into place using the locking bolts (D).
SECURING TV TO MOUNT

Set your cable management according to the images below, then tighten the mount using
the spanner to lock mount into position.