Kohler K-99696-NA Assembly instructions

Installation and Care Guide
Amplifier
K-99696-NA
Français, page ″Français-1″
Español, página ″Español-1″
1232038-2-C

IMPORTANT INSTRUCTIONS
WARNING: When using electrical products, basic
precautions should always be followed, including the
following:
WARNING: Risk of electric shock. A qualified electrician
should route all electrical wiring.
WARNING: Risk of electric shock. Disconnect power before
servicing.
CAUTION: Risk of product damage. The amplifier is rated to
operate in temperatures up to 104°F (40°C). Do not install near heat
sources (such as radiators or heat registers) or in any location where
the temperature may exceed 104°F (40°C).
NOTICE: This product is not water-resistant. Do not install in a
location where excessive moisture, high humidity levels, or
condensation are present.
NOTICE: Follow all electrical and building codes.
NOTICE: Provide unrestricted service access to the amplifier.
NOTICE: Provide a minimum of 6″(152 mm) of space around the
amplifier for proper air flow.
NOTE: This amplifier can be operated as a stand-alone unit, or can
be installed with the DTV+ showering system.
_________________________________________________________________
Operation with DTV+
To connect the amplifier to the DTV+ system, the K-99695 system
controller is required.
The provided data cable is used to connect the amplifier to the
system controller.
Refer to the ″DTV+ System Layout″section in this guide.
Before Operating the System For the First Time:
Download and install the latest software for connected components.
This may take an hour or more to complete based on system
configuration and internet connection speed. Do not disconnect the
power from any components during software download and
installation.
1232038-2-C 2 Kohler Co.

FCC, IC, and CE Compliance
Contains: Kohler Company, Model: K-99696-NA, FCC ID:
N82-KOHLER010, IC: 4554A-KOHLER010, CE: CE2200
IFT Certification Number: 201801A02469
FCC Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including
interference that may cause undesired operation.
Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate
the equipment.
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for
help.
Industry Canada Statement
This device complies with Industry Canada licence-exempt RSS
standard(s). Operation is subject to the following two conditions:
1. This device may not cause interference, and
2. This device must accept any interference, including interference that
Kohler Co. 3 1232038-2-C

FCC, IC, and CE Compliance (cont.)
may cause undesired operation of the device.
CAN ICES-3(B) /NMB-3(B)
CE2200
Range and Function Disclaimer
BLUETOOTH
®
is the name for a short-range radio frequency (RF)
technology that operates at 2.4 GHz. The effective range of most
BLUETOOTH mobile devices is 10 meters. BLUETOOTH is designed
for very low power use. The compatibility of the BLUETOOTH
amplifier interface to mobile/portable devices differs according to the
various individual devices and, in particular, may vary with different
software versions for a device. The normal mobile device
BLUETOOTH range can be up to 10 meters, however, placement of
your mobile device and the BLUETOOTH amplifier’s installation
environment will impact your reception range.
Water and walls can act as blocking agents to the BLUETOOTH signal
that your mobile device is using to broadcast to your BLUETOOTH
amplifier. Therefore, selecting an installation location that removes
these range blocking obstacles will increase the effective range and
performance of your BLUETOOTH amplifier.
You can test your BLUETOOTH reception by performing simple range
tests using your mobile device prior to performing a permanent
installation. The best way to make use of the short BLUETOOTH range
is to make sure your BLUETOOTH amplifier is as close to the
BLUETOOTH transmitter (mobile phone, tablet, etc.) as possible. The
less distance between the two devices, the greater will be the reliability
of your BLUETOOTH audio signal, and the less distance means less
obstacles in the medium through which the transmission is passing, so
there is a reduced chance of audio signal loss.
The compatibility of the BLUETOOTH amplifier to mobile/portable
devices differs according to the various individual devices and, in
particular, may vary with different software versions for a device. All
functions are based on industry-wide communications standards.
Compatibility between the BLUETOOTH amplifier and mobile device
is therefore largely dependent upon the software version of the mobile
device. Other factors (e.g. installation location, walls, distance) mean
that in individual cases, sporadic impairment of functions may occur in
devices that otherwise function reliably. Not all functions are
supported in all countries.
Because of these reasons, Kohler Co. can assume no guarantee for the
1232038-2-C 4 Kohler Co.

Range and Function Disclaimer (cont.)
unlimited compatibility and functionality of your mobile device in
conjunction with the BLUETOOTH amplifier.
_________________________________________________________________
The BLUETOOTH
®
word mark and logos are registered trademarks
owned by Bluetooth SIG, Inc. and any use of such marks by Kohler
Co. approved suppliers is under license. Other trademarks and trade
names are those of their respective owners.
Specifications
Ambient Temperature Max 104°F (40°C)
Maximum Relative Humidity 90% non-condensing
Electrical Service 100-240 VAC, 50-60 Hz, 1.2 A Max
Power Cable Length 69″(1753 mm)
Data Cable Length 6’ (1.83 m)
Output Power 20 Watts x 2 into 4 Ohms
Frequency Response 20 Hz - 18 kHz +/- 3dB
Signal/Noise Ratio >75 dB
Total Harmonic Distortion <0.1% at 1 Watt, <1% at full output
power
Tools and Materials
• Wire Cutter/Stripper
Plus:
Kohler Co. 5 1232038-2-C

Before You Begin
Determine amplifier and speaker locations before beginning
installation. Test the BLUETOOTH
®
range between the amplifier
and your wireless device when determining amplifier location.
The amplifier can be mounted in any orientation. Use the
supplied brackets or rubber feet to accommodate your mounting
configuration.
Locate the amplifier within close proximity to a 15 A, 120 V
electrical outlet. A GFCI outlet may be required in certain
applications.
A qualified electrician should install any electrical outlet.
If possible, install the electrical outlet prior to installing the
amplifier.
This amplifier complies with CE, FCC, and IC.
1232038-2-C 6 Kohler Co.

1. Preparation
Plan the location of the amplifier to allow access to the front and
back ports.
To play your personal music files, you need a wireless
BLUETOOTH device, or a device with a 3.5 mm stereo cable
connection.
The speaker terminal connections on the amplifier will accept a
12-24 AWG wire. Follow local codes for speaker wire type and
routing.
Allow adequate reach for wires between the amplifier and
speaker locations.
Make sure the LED light will be visible after installation.
For DTV+: Allow adequate reach for the data cable between the
amplifier and the system controller, or obtain a longer
Ethernet-style cable or extension cable.
LED
Front Back
Power
Cable
Speaker
Terminal
3.5 mm
Line-Out
DTV+ Data
Cable
3.5 mm
Line-In (1)
3.5 mm
Line-In (2)
Kohler Co. 7 1232038-2-C

2. Installation
CAUTION: Risk of product damage. The amplifier is rated to
operate in temperatures up to 104°F (40°C). Do not install near heat
sources (such as radiators or heat registers) or in any location where
the temperature may exceed 104°F (40°C).
NOTICE: Mount the amplifier in a dry location, and provide a
minimum of 6″(152 mm) of space for proper air flow.
Mounting Options
Surface-mount: Attach the four rubber feet to the underside of
the amplifier to protect against scratching your shelf or
countertop surface.
Cabinet-mount: Install the amplifier using the mounting brackets
and short screws.
Under-mount: Flip the orientation of the brackets on the amplifier
to install it in an upright position.
Wall-mount: Secure the amplifier using the mounting brackets,
long screws, and wall anchors (if needed).
Surface-Mount
Wall-Mount
Under-Mount
Anchor
Foot
Cabinet-Mount
1232038-2-C 8 Kohler Co.

Installation (cont.)
Bracket Installation
Position the amplifier with attached brackets in the desired
location.
Mark the bracket hole locations with a pencil.
Drill pilot holes or insert anchors as needed at the marked
locations.
Secure the brackets using the four screws provided.
Kohler Co. 9 1232038-2-C

3. DTV+ System Layout
The amplifier can be controlled digitally when connected to the
K-99695 system controller. The controller powers the interface(s) and
controls the amplifier and other system components.
NOTE: A data cable is provided to connect the amplifier to the
controller. If the amplifier is not within 6’ (1.83 m) of the controller,
obtain a longer Ethernet-style cable or add an extension cable.
Disconnect the power from the amplifier and the controller.
Connect one end of the data cable into the port on the back of the
amplifier.
Connect the other end of the cable into one of the eight grouped
component ports on the controller.
Reconnect the power to the amplifier and the controller.
Before Operating the DTV+ System For the First Time:
Download and install the latest software for connected components.
This may take an hour or more to complete based on system
configuration and internet connection speed. Do not disconnect the
power from any components during software download and
installation.
For more information on system setup and operation, refer to the
guide on the controller product page at www.us.kohler.com.
Controller
Digital
Valve(s)
Speakers
AC Power
Component
Cable
Connections
Amplifier
6' (1.83 m) Data Cable
Router
Interface
(Up to Three)
AC
Power
1232038-2-C 10 Kohler Co.

4. Speaker Connections
NOTE: This amplifier allows 2- or 4-speaker stereo output. Refer to
the connection diagram above for your wiring configuration.
NOTE: The speaker terminal will accept a 12-24 AWG wire. Follow
local codes for routing speaker wires.
Disconnect the power from the amplifier.
Using a wire stripper, remove approximately 1/2″(13 mm) of
insulation from the speaker wire.
Insert the wire into the appropriate positive (+) or negative (-)
and right (R) or left (L) terminal connector.
Repeat for the remaining speaker wires.
Reconnect the power to the amplifier.
Verify that the status LED light turns on.
Series Connection - 4 Ohm Parallel Connection - 8 Ohm
Or
Speaker Terminal
+- +-+-+-
+- +-
RL
+
RL
+-+
-
-+
-
-+-
RL
-++-+
+- +-
Kohler Co. 11 1232038-2-C

5. Operation
NOTE: Set your music device to a midrange volume after
connecting to the amplifier, but prior to sending an audio signal
from the device.
Status LED Light
Yellow = standby mode.
Blue blink = standby mode with BLUETOOTH
®
connection.
Blue = audio input from a BLUETOOTH device.
Green = audio input from the front or back 3.5 mm line-in port.
3.5 mm Stereo Input
A wired audio device can be connected to either the front or back
line-in ports.
The front line-in port (1) will override the back port (2).
Once a signal is detected from the device, the LED will turn
green and the audio input will fade in.
If the LED does not turn green when the device is turned on,
increase the volume on the device.
Audio input may be slightly delayed when a device is initially
connected.
Wireless Input
Once a BLUETOOTH device is connected, the LED will blink
blue.
The amplifier will display on the device as ″Kohler KA02.″
If a BLUETOOTH pin is required, enter ″0000.″
LED
Front Back
Power
Cable
Speaker
Terminal
3.5 mm
Line-Out
DTV+ Data
Cable
3.5 mm
Line-In (1)
3.5 mm
Line-In (2)
1232038-2-C 12 Kohler Co.

Operation (cont.)
NOTE: If connected to a DTV+ system, the pin and device name
can be changed using the controller Web pages.
Upon receiving a wireless signal, the LED will turn solid blue and
the audio input will fade in.
Wireless input will override any signal that may be coming from
the front or back line-in ports.
3.5 mm Stereo Output
A line-out port is available to provide unamplified stereo output
of the audio signal that can be fed to another external device.
Standby Mode
If no audio signal is detected for 30 seconds from the 3.5 mm
line-in ports, the amplifier will go into standby mode and the
LED will turn yellow.
BLUETOOTH Standby: If no audio signal is detected for 30
seconds from a connected wireless device, the amplifier will go
into BLUETOOTH standby mode and the LED will change from
solid blue to blue blink.
DTV+ Operation
For information on operating the amplifier using the DTV+
system, refer to the guide on the K-99695 controller product page
at www.us.kohler.com.
Troubleshooting
IMPORTANT! Turn off the power supply before performing any
maintenance.
NOTE: For DTV+ system troubleshooting, refer to the guide on
the K-99695 controller product page at us.kohler.com.
NOTE: For service parts information, visit your product page at
kohler.com/serviceparts.
This troubleshooting guide is for general aid only. For service and
installation issues or concerns, call 1-800-4KOHLER.
Kohler Co. 13 1232038-2-C

Troubleshooting (cont.)
Troubleshooting Table
Symptoms Probable Cause Recommended Action
1. One or both
speakers do
not produce
sound, or
sound is too
low in a two
speaker setup.
A. Speaker cable is
not plugged in
properly.
A. Make sure the cables
are properly installed
into the amplifier
connections and to
the left and right
speakers.
2. One or more
speakers do
not produce
sound, or
sound is too
low in a four
speaker setup.
A. Damaged speaker
or speaker not
plugged in.
A. Make sure the
speaker cables are
properly installed
into the appropriate
positive (+) and
negative (-)
connectors on the
amplifier.
B. Speaker cable is
not connected
properly.
B. Connect 4 Ohm
speakers in series
and 8 Ohm speakers
in parallel.
3. After playing
music loudly,
the music stops
even though a
song is
properly
selected.
A. Thermal shut
down. A. Shut down the system for 1 hour to
allow the unit to
cool. Make sure the
area where the unit
is installed does not
exceed 104°F (40°C).
4. The status LED
is not
illuminated.
A. Power supply is
not plugged into
the outlet.
A. Plug the power
supply into the
outlet.
B. Power supply
connection to the
amplifier may be
loose or
disconnected.
B. Check power supply
connection to the
amplifier and
reconnect if needed.
C. The outlet is not
powered. C. Make sure there is power to the
electrical outlet.
D. Circuit breaker has
been tripped. D. Reset the circuit breaker.
1232038-2-C 14 Kohler Co.

Troubleshooting (cont.)
Troubleshooting Table
Symptoms Probable Cause Recommended Action
5. No sound
plays through
the speakers.
A. The song is
paused. A. Make sure a song is playing. If the song
is paused, press the
resume feature to
continue playback.
B. The volume is too
low. B. Make sure the volume is turned up
high enough for
proper enjoyment.
6. The amplifier
is not
connecting to
my
BLUETOOTH
®
device.
A. The BLUETOOTH
device is not
within range.
A. Make sure the
BLUETOOTH device
is within range of
your amplifier.
B. The BLUETOOTH
device is not
paired with the
amplifier.
B. Pair your
BLUETOOTH device
with the amplifier
according to the
pairing instructions
for your
BLUETOOTH device.
7. The LED is
blue, but the
audio signal is
intermittent.
A. The BLUETOOTH
device is not
within full range.
A. Move the
BLUETOOTH device
closer to the
amplifier location.
Warranty
KOHLER
®
Electronic Faucets, Valves and Controls FIVE-YEAR
LIMITED WARRANTY
Kohler Co. warrants that its electronic faucets, valves and controls will
be free of defects in material and workmanship during normal
residential use for five years from the date the product is installed.
This warranty applies only to electronic faucets, valves and controls
installed in the United States of America, Canada and Mexico (″North
America″).
If a defect is found in normal residential use, Kohler Co. will, at its
election, repair, provide a replacement part or product, or make
appropriate adjustment where Kohler Co.’s inspection discloses any
such defect. Damage caused by accident, misuse, or abuse is not
Kohler Co. 15 1232038-2-C

Warranty (cont.)
covered by this warranty. Improper care and cleaning will void the
warranty*. Proof of purchase (original sales receipt) must be provided
to Kohler Co. with all warranty claims. Kohler Co. is not responsible
for labor charges, installation, or other incidental or consequential costs
other than those noted above. In no event shall the liability of Kohler
Co. exceed the purchase price of the faucet, valve or control
If you believe that you have a warranty claim, contact your Home
Center, Dealer, Plumbing Contractor or E-tailer. Please be sure to
provide all pertinent information regarding your claim, including a
complete description of the problem, the product, model number, the
date the product was purchased, from whom the product was
purchased and the installation date. Also include your original invoice.
For other information, or to obtain the name and address of the service
and repair facility nearest you, write Kohler Co., Attn: Customer Care
Center, Kohler, Wisconsin 53044 USA, or by calling 1-800-4-KOHLER
(1-800-456-4537) from within the USA and Canada, and
001-800-456-4537 from within Mexico, or visit www.kohler.com within
the USA, www.ca.kohler.com from within Canada, or
www.mx.kohler.com in Mexico.
THE FOREGOING WARRANTIES ARE IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT
LIMITED TO THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE.
KOHLER CO. AND/OR SELLER DISCLAIM ANY LIABILITY FOR
SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some
states/provinces do not allow limitations on how long an implied
warranty lasts or the exclusion or limitation of such damages, so
these limitations and exclusions may not apply to you. This warranty
gives the consumer specific legal rights. You may also have other
rights that vary from state/province to state/province. This warranty
is to the original consumer purchaser only, and excludes product
damage due to installation error, product abuse, or product misuse,
whether performed by a contractor, service company, or the
consumer.
This is Kohler Co.’s exclusive written warranty.
*Never use cleaners containing abrasive cleansers, ammonia, bleach,
acids, waxes, alcohol, solvents or other products not recommended
for chrome. This will void the warranty.
1232038-2-C 16 Kohler Co.

Guide d’installation et d’entretien
Amplificateur
K-99696-NA
Kohler Co. Français-1 1232038-2-C

INSTRUCTIONS IMPORTANTES
WARNING: Lors de l’utilisation de produits électriques,
toujours observer les précautions de base, dont les
suivantes :
WARNING: Risque de choc électrique. Tout le câblage
électrique doit être réalisé par un électricien qualifié.
WARNING: Risque de choc électrique. Déconnecter
l’alimentation électrique avant d’effectuer un entretien.
CAUTION: Risque d’endommagement du produit. L’amplificateur
est destiné à fonctionner à des températures de 104°F (40°C)
maximum. Ne pas installer à proximité de sources de chaleur
(comme des radiateurs ou des registres de chaleur), ni dans des
endroits où la température pourrait dépasser 104°F (40°C).
NOTICE: Ce produit n’est pas hydrorésistant. Ne pas installer
dans un endroit avec une humidité excessive, avec des niveaux de
haute humidité ou avec condensation.
NOTICE: Respecter tous les codes électriques et codes du bâtiment
locaux.
NOTICE: Fournir un accès libre à l’amplificateur aux fins
d’entretien.
NOTICE: Fournir un minimum de 6 po (152 mm) d’espace autour
de l’amplificateur pour assurer une circulation d’air appropriée.
NOTE: Cet amplificateur peut être utilisé comme unité autonome
ou il peut être installé avec le système de douche DTV+.
_________________________________________________________________
Fonctionnement avec DTV+
Pour connecter l’amplificateur au système DTV+, le module de
commande du système K-99695 est requis.
Le câble de données fourni est utilisé pour connecter
l’amplificateur au module de commande du système.
1232038-2-C Français-2 Kohler Co.

INSTRUCTIONS IMPORTANTES (cont.)
Se référer à la section « Disposition du système DTV+ » dans ce
guide.
Avant de faire fonctionner le système la première fois :
Télécharger et installer le dernier logiciel pour les composants
connectés. Une heure ou plus peuvent être nécessaires en fonction de
la configuration du système et de la vitesse de connexion internet. Ne
pas déconnecter l’alimentation électrique des composants pendant le
téléchargement et l’installation du logiciel.
Conformité FCC, IC et CE
Contenu : Kohler Company, Modèle : K-99696-NA, ID FCC :
N82-KOHLER010, IC : 4554A-KOHLER010, CE : CE2200
Numéro de certification IFT : 201801A02469
Déclaration d’interférence FCC
Cet appareil est conforme à la section 15 des réglementations de la
FCC. L’exploitation est autorisée aux deux conditions suivantes :
1. Cet appareil ne doit pas provoquer d’interférences néfastes, et
2. Cet appareil doit tolérer les interférences reçues, y compris celles qui
risquent de provoquer un fonctionnement indésirable.
Tous changements ou modifications non expressément approuvés par
la partie responsable garantissant la conformité, pourraient annuler le
droit à l’utilisateur d’opérer l’équipement.
Cet appareil a été testé et est considéré conforme aux limitations d’un
appareil numérique de classe B, selon la section 15 des réglementations
FCC. Ces limites sont conçues pour fournir une protection raisonnable
contre toute interférence nuisible lors d’une installation résidentielle.
Cet appareil génère, utilise et peut émettre une énergie de
radiofréquence et, s’il n’est pas installé et utilisé conformément aux
instructions, pourrait être la cause d’interférences nuisibles aux
communications par radio. Cependant, il n’est pas garanti qu’aucune
interférence n’aura lieu dans une installation particulière. Si cet
appareil cause des interférences nuisibles à la réception radio ou
télévision, ce qui peut être déterminé en éteignant l’appareil et en le
rallumant, il est recommandé d’essayer de rectifier cette interférence en
prenant l’une ou plusieurs des mesures suivantes :
•Réorienter ou changer l’emplacement de l’antenne de réception.
Kohler Co. Français-3 1232038-2-C

Conformité FCC, IC et CE (cont.)
•Augmenter la séparation entre l’équipement et le récepteur.
•Brancher l’équipement sur une prise d’un circuit différent de celui
auquel le récepteur est connecté.
•Consulter un revendeur ou un technicien radio/TV expérimenté
pour obtenir de l’assistance.
Déclaration d’Industrie Canada
Le présent appareil est conforme aux CNR d’Innovation, Sciences et
Développement économique Canada applicables aux appareils radio
exempts de licence. L’exploitation est autorisée aux deux conditions
suivantes :
1. L’appareil ne doit pas produire de brouillage, et
2. Cet appareil doit tolérer les interférences reçues, y compris celles qui
risquent de provoquer un fonctionnement indésirable.
CAN ICES-3(B) /NMB-3(B)
CE2200
Non responsabilité pour la portée et le fonctionnement
BLUETOOTH
®
est le nom d’une technologie de radiofréquence (RF) à
courte portée qui fonctionne à 2,4 GHz. La portée efficace de la plupart
des appareils mobiles BLUETOOTH est de 10 mètres. Les appareils
BLUETOOTH sont conçus pour une utilisation très faible de courant.
La compatibilité de l’interface de l’amplificateur BLUETOOTH avec les
appareils mobiles/portables varie en fonction des divers appareils
individuels, et, en particulier, elle peut varier avec des versions de
logiciel différentes pour un appareil. La portée BLUETOOTH normale
d’un appareil mobile peut aller jusqu’à 10 mètres, mais le
positionnement de l’appareil mobile et de l’environnement de
l’installation de l’amplificateur BLUETOOTH aura un impact sur la
portée de réception.
L’eau et les murs peuvent avoir un effet d’agents bloquants pour le
signal BLUETOOTH que votre appareil mobile utilise pour émettre
vers votre amplificateur BLUETOOTH. C’est pourquoi, le choix d’un
emplacement d’installation qui supprime ces obstacles de blocage de la
portée augmente la portée efficace et la performance de votre
amplificateur BLUETOOTH.
La réception de votre appareil BLUETOOTH peut être testée par de
simples essais de portée en utilisant votre appareil mobile avant de
procéder à une installation permanente. La meilleure manière d’utiliser
1232038-2-C Français-4 Kohler Co.