Kohler EVOK 2.0 25163A-0 User manual

Please read these instructions carefully to
familiarize yourself with the required tools, materials,
and installation sequences. Follow the sections that
pertain to your particular installation. This will help
you avoid costly mistakes. In addition to proper
installation, read all operating and safety instructions.
All information is based on the latest product
information available at the time of publication.
Kohler NZ Ltd. reserves the right to make
changes in product characteristics, packaging, or
availability at any time without notice.
These instructions contain important information
- Please leave these instructions for the consumer.
Please provide adequate available space for the
bath unit in accordance with rough-in. Arrange the
location of drain in advance.
All installations must comply with council and local
authority by-laws. It is the responsibility of the installer
to ensure that the waste is made watertight.
IMPORTANT:
NOTE: The bath can be installed after the wall is
A. Summary Of Key Requirements
Observe all local plumbing codes.
Install the unit to a level subfloor.
PRODUCT REQUIREMENTS
B. Plumbing Specifications
If using a rim-mounted bath faucet, flexible connections between the valves and spout may be required.
Confirm adequate mounting, connection space of specified faucet for your installation.
C. Product Inspection
Uncrate and inspect bath for damage. All Kohler s baths have been manufactured with sophisticated craftsmanship.
However, please inspect for any possible damage that may have occurred in transit. Leave all materials in the carton
during construction to prevent damage.
’
1
BEFORE YOU BEGIN
EVOK 2.0
INSTALLATION INSTRUCTIONS
25/02/2021
25163A-0 / 25164A-0 / 25165A-0 / 25166A-0 / 25167A-0
EVOK 2.0 SEAMLESS FREESTANDING BATHS
NOTE: Damage occurred during transit shall not be covered by warranty.
D. New or Replacement Installation Requirements
This bath can be installed in new or existing bathrooms. Check the roughing-in and room dimensions to provide.
For replacement: Remove the old bath, and remove enough old wall material and floor covering from the
area to allow for installation. Remove any old plumbing that does not conform to the rough-in requirements.
For new installation: Position the plumbing according to the rough-in dimensions. Cap the supplies, and check
for leaks.
completed. Bath drain supplies should be arranged
preliminarily according to the selected bath.
adequate available space for the bath unit.
1475013-A2-A

1500
750
610
1128
5
25163A-0
1700
850
750
610
1377 622
5
25164A-0
1700
1450 689
850
750
610
5
25165A-0
1600
1350 689
800
750
610
5
1500
1250 689
750
750
610
5
25163A-0 25164A-0 25165A-0 25166A-0 25167A-0
Water depth to overflow 410mm 410mm 410mm 410mm 410mm
Capacity to overflow 390 L 282 L 284 L 256 L 228 L
Bathing area 908 mm 835 x 424 mm 1127 x 564 mm 1027 x 564mm 927 x 564 mm
Top area 1450 mm 1648 x 699 mm 1642 x 695 mm 1542 x 695 mm 1442 x 695 mm
E Rough-in Dimensions (mm)
25166A-0
25167A-0
2

Adjustable pipe
wrench
Ruler
Level
Safety shoes
Safety glasses
Square
Screwdriver
Pliers
Utility knife
Plumbers putty
Wall coverings(as necessary)
Silicone sealant
B. Materials RequiredA. Tools Required
INSTALLATION REQUIREMENTS
3
BEFORE INSTALLING UNIT
A. Protect the Bath Unit
Position a protective covering underneath the bath and be careful not to scratch the bath surface.
SITE REQUIREMENTS
A. Preparation
Check the flooring under the bath, and make repairs as necessary. Make sure the subfloor is level. It is strongly
recommended to prepare a waterproof layer for the subfloor beforehand. It may be necessary to plan for a
Subfloor
D. Clearance Requirements
C. Installation Note:
Read the entire installation instruction manual supplied with this bath before beginning the installation. If installing
a rim-mount faucet, make sure there is no interference with the drain overflow before drilling any holes.
Check the rough-in and room dimensions to ensure there is adequate available space for the bath.
channel in the floor to allow space for a trap, see cross section below:
NOTES:
1. Flush the water supply pipes thoroughly to remove debris.
2. Inspect the supply tubing for damage. Replace as necessary.
3. Observe local plumbing codes.

INSTALLATION
1) Unpack bath shell and skirt and check for any transit damage prior to installation.
2) Position the bath in the desired location in the bathroom.
3) Check that the plumbing can be connected to the bath when in the desired location.
4) Adjust the feet so that the bath is level. The distance from the feet to the top of the bath should conform to the
rough-in dimensions.
CAUTION: The weight of the bath should be supported by the bath feet.
2) Connect the bath waste & a DN32 to DN40 adapter to an appropriate trap.
Connect the adapter and drain pipe on one end, and
the supplied cap on the other end.
3) After plumbing is complete and before lowering the bath check all connections are water tight, check for leaks.
Kohler NZ shall not be liable under warranty for damage caused by negligence.
4)
5) If there are no leaks, apply a thin continuous bead of clear or color-matched silicone sealant to the seam
between the bath and the finished floor. Leave the bath for a minimum of 24 hours to allow the silicone to cure.
Apply silicone sealant
1) To connect the plumbing raise the freestanding bath off the floor by propping it up onto timber blocks positioned
at either end of the bath.
PLUMBING INSTALLATION
Carefully lower the bath back onto the floor. Take care while maneuveruing the bath not to damage the base of
the bath and subfloor.
4

5
• Ensure a watertight seal on the bath drain and plumbing.
• Install the faucet valve according to the faucet manufactuer’s instructions.
• Do not install the faucet trim until instructed.
• Turn on the hot and cold water supplies and check connections for leaks.
INSTALLATION COMPLETE
CLEANING AND CARE
• Use a mild detergent such as liquid dishwashing soap and warm water to clean the bath. Do not use
abrasive cleaners that may scratch or dull the surface.
• Take care to read the label of cleaning products to ensure the cleaner is safe for use with acrylic material.
• Before using an intended cleaning product, test the cleaning solution on an inconspicuous surface.
• Do not allow cleaners to sit or soak into the surface of the bath.
• Wipe surfaces clean and rinse completely with water immediately after cleaner is applied.
• Use a soft dampened cloth or sponge. Never use an abrasive material such as a scouring pad to clean
bath surfaces.
CAUTION: Risk of property damage
IM RMA
N
SERVICE PARTS
CONTACT AND WARRANTY INFORMATION
For spare parts and warranty information, please visit our website:
New Zealand Australia
www.kohler.co.nz www.kohler.com.au
NEW ZEALAND AUSTRALIA
KOHLER NZ LTD KOHLER AUSTRALIA
Ph: 0800 564 537 Ph: 1 800 564 537
Fx: 0800 664 488
Product Code Descrip�on
1466888-* Evok 2 Bath Drain kit
1022879 Bath foot kit