American Standard Colony 2740 Series User manual

INSTALLATION INSTRUCTIONS
GENERAL INSTALLATION INFORMATION
Carefully uncrate and inspect your new bath for any shipping
damage. If such damage is found, report it to your vendor
immediately.
After inspection and during installation, protect the bath from
construction damage. Before installation, and before
enclosing with wallboard, tile, etc., water test the unit and
check for leaks.
If a whirlpool, do not make modifications to the whirlpool system
or remove pump from factory mounting. This could adversely
affect the safety and performance of the whirlpool and void the
warranty. Do not handle or move the whirlpool by the pump,
motor, or piping system.
Fittings (bath filler, shower arm, etc.) are not provided with the
bath and must be ordered separately. Framing and enclosing
materials are provided by others.
752562-100 Rev. H
© AS America, Inc. 2008
All product names listed herein are trademarks
of AS America, Inc. unless otherwise noted.
INTEGRAL APRON WITH
REMOVABLE ACCESS PANEL
FOR ABOVE-FLOOR
ROUGH INSTALLATION
HIGH GLOSS ACRYLIC
SHOWN LESS ALL FITTINGS
COLONY™ 5 x 30 AFR
WHIRLPOOL/BATHING POOL
2740.XXX SERIES
GENERAL INSTALLATION INFORMATION
Bath may only be installed in a recess type installation.
Locate studs as required. Insure rough dimensions are proper, plumb and square. For whirlpools, access to pump/motor may be made through
access opening in apron panel. The following procedure must be used for all installations: leveling support stringer should be as indicated. This bath is
not self-supporting and must be supported along it's entire bottom. Support with mortar or grout.
Position bathtub/whirlpool within the recess, check level, front to back, side to side, and shim as necessary.
To secure the tub to wood studs use drywall screws w/washers or roofing nails immediately above the flange of the tub. To secure the tub to steel studs
use 4" drywall screws and flatwashers.
See page 2 for complete installation information.
Caution: Take extra care when driving nails or screws to avoid damaging the tub.
The tile or similar finished floor will be butted against the bottom of the tub apron, also holding the tub in place.
FOR AFTER-SALES SERVICE CALL 1 [phone] WEEKDAYS.
IMPORTANT:
Water test unit before installation and enclosure!
THANK YOU...
for selecting an American Standard bath. Your new bath is shipped
to you after careful inspection. The whirlpool version is completely
assembled with pump, motor, and system piping. All you need to
finish the installation are your selected fittings and electrical
connections for a whirlpool.
To insure maximum performance and pleasure from this product,
please follow the instructions and cautions.
List of Required Components (not included):
• Drain 1583.470* • Bath Filler*
* see your American Standard Distributor
List of Required Tools and Supplies:
Tools
• Level
• Tape Measure
• Pipe Wrench
• Slip Joint Pliers
• Screw Driver
• Standard
Woodworking Tools
• Personal Safety
Equipment
• Caulking Gun
Supplies
• Nails
• Putty
• Caulking (waterproof)
• 1 x 3 or 2 x 2
Stringers
• Drop Cloth
• 15 amp GFI
Outlet
• Cement, Plaster,
Grout
GENERAL SPECIFICATIONS FOR 2740 WHIRLPOOL
WHIRLPOOL ELECTRICAL SPECIFICATIONS
SYSTEM I PUMP 1.1 HP, 9.9 AMPS,120V.
59-7/8 x 29-7/8 x 19-1/4 (1521 x 759 x 489mm)
105 Lbs. (47 Kgs.)
480 Lbs. (216 Kgs.)
45 Gal. (171 L)
38 Gal. (144 L)
20 x 46 (508 x 1168mm )
25-1/2 x 55-1/2(648 x 1410mm )
11-1/2 (292mm)
39 Lbs./Sq.Ft. (188 Kgs./Sq.m)
20.8
35.3
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
WHIRLPOOL MIN. OPERATING VOL.
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
CUBE (FT3)
59-7/8
(1521mm)
29-7/8
(759mm)
WATER
RETENTION
FLANGE
(3 SIDES)
7
(178mm)
C/L OF DRAIN
1-1/2 (38mm) (6) JETS
PUMP
FINISHED
WALL
3/4
(19mm)
C/L OF
SUPPLIES
HORIZONTAL TAILPIECE
ABOVE FLOOR OUTLET
1-1/2 O.D.
TAILPIECE
SEE FITTING
SPECS FOR
DIMENSIONS
(1) AIR VALVE
ON/OFF
SWITCH
ACCESS TO PUMP/MOTOR
THROUGH REMOVABLE
FRONT ACCESS PANEL
14-1/8
(359mm)
BATH SUPPORT
MATERIAL
19
(483mm)
7/8 WATER
RETENTION
FLANGE
(3 SIDES)
19-1/4
(489mm)
ROUGH
FLOOR
FINISHED
WALL
TOP OF
DECK
3
(76mm)
3-3/4
(95mm)
OPTIONAL TO
FINISHED FLOOR
USUALLY BETWEEN
65 & 78
(1651 & 1981mm)
C/L OF
OVERFLOW
12
(305mm)
OPT. 4
(102mm)
C/L OF
SPOUT
C/L OF
VALVES
C/L OF
SHOWER ARM
2-1/2
(64mm)
UNDERSIDE
OF DECK
LEVELING
STRINGER
NOT FOR
SUPPORT
TILING
FLANGE

INSTALLATION AND FRAMING INSTRUCTIONS
Locate studs as required. Ensure roughing-in dimensions are proper, plumb and square. Access to Pump/Motor may be
made through the access opening in the apron panel. It is strongly recommended that an additional opening be provided
for access to the drain components.
NOTE: The apron may be used as the primary access opening.
1. As shown in Fig. 1, mark the position of the underside of the deck by tracing a line onto the studs at the height indicated,
using a level or other suitable straight edge.
2. With the top of the stringer touching the traced line, attach the stringer to the studs.
3. Install drain components to the whirlpool or bath following the manufacturers instructions.
4. THIS BATH MUST BE SUPPORTED ALONG ITS ENTIRE BOTTOM. We recommend the use of mortar as bedding
material (sand is not recommended). Apply enough bedding to support the complete bottom of the bath. After the
bedding has been poured, and before it sets, position whirlpool or bath within recess until the rim is leveled against the
leveling stringers (see "Typical Recess Installation") shown below. The rim of the bath MUST NOT support weight.
Allow the bedding material to completey harden before applying weight to the rim or bottom of the bath. Any finish
material such as tile or wall board must be self-supporting if it contacts the deck of the bath.
752562-100 Rev. H 2
19
(483mm)
FIG. 1
TYPICAL RECESS INSTALLATION
34 Typ.
(864mm)
19
(483mm)
60-3/16
(1529mm)
30
(762mm)
32
(813mm)
TUB WIDTH
LEVELING
STRINGERS
SUGGESTED WHIRLPOOL/BATH INSTALLATION METHOD
Leveling Stringer
1 x 3 (25 x 76mm) WOOD
Finished Wall
Waterproof Dry Wall
or Cement Board
Sealant
Tub
Stud
(Wood or Steel)
SECURE THE BATH TO THE STUDS AS SHOWN FOR
WOOD OR STEEL STUD CONSTRUCTION.

ELECTRICAL DIAGRAM
READ AND FOLLOW ALL INSTRUCTIONS
BLACK
WHITE
120 VAC
GND.
SEPERATE 15 AMP
GFCI OUTLET
WHIRLPOOL MOUNTED
AIR SWITCH OR
WALL TIMER
ELECTRICAL INSTALLATION
PUMP/MOTOR
752562-100 Rev. H
ELECTRICAL INSTALLATION INSTRUCTIONS
All wiring must be performed by a licensed electrician in accordance with the national electrical code and all other
applicable codes.
WARNING: When using electrical products, basic precautions should always be observed, including the following:
1. DANGER: RISK OF ELECTRIC SHOCK Connect only to a circuit protected by a ground-fault circuit interrupter.
2. Grounding is required. The unit should be installed by a licensed electrician and grounded.
3. Install to permit access for servicing.
4. All building materials and wiring should be routed away from the pump body and heater (if equipped).
The whirlpool should be installed on a 120 vac, 15 amp dedicated circuit. The circuit should be hard-wired from the
electrical power supply panel. The circuit must be a three (3) wire circuit from the electrical supply panel. A grounded
neutral wire and a third wire, earth ground, are essential.
3

WIRE SELECTION GUIDE
Maximum distance from
fusebox to motor The sizes shown on this
chart are recommendations
for copper conductors
only. Always follow
local and national
electrical codes
Motor High
Performance
Rating 50' 100'
115V Power Line
150' 200'
12 12 10 8
1.1
4SPIC AND SPAN®IS A REGISTERED TRADEMARK OF PROCTER & GAMBLE
752562-100 Rev. H
DRAIN CONNECTION AND SYSTEM TEST
Using recommended drain opening, connect whirlpool drain to waste line. Tighten all drain joints securely. Check the pump
couplings and make sure they are hand-tight. Clean the whirlpool and fill with water to a point 2" above the top of the highest jet.
Recheck the pump couplings and make certain that they are not leaking. (Although the pump couplings are factory tightened and
inspected, some loosening may have occurred during transit.) Make sure the whirlpool is connected to the electrical supply and turn
the whirlpool on. Check for leaks around all piping connections while the whirlpool is running.
POST INSTALLATION CLEAN-UP
Remove all construction debris from bath. Tile grout can be removed with a wooden popsicle stick or tongue depressor. Do not use
wire brushes or any other metal implement on bath surface.
Post installation clean-up generally can be completed using warm water and liquid dishwashing detergent. Stubborn dirt or stains
may be removed using granular Spic and Span®mixed with water.
Painter's naphtha can be used to remove excess adhesives and/or wet oil-base paint.
FEATURES of YOUR NEW AMERICAN STANDARD ACRYLIC BATHTUB
Your new acrylic bathtub has been molded in the newest plumbing fixture material available today. Acrylics are tough
durable finishes that are simple and easy to care for.
The colors have been formulated to match other American-Standard fixtures and enhance your choice of bathroom
decorations. The high gloss surface is resistant to impact and chemicals and will retain its lasting luster with proper
care and maintenance.
AFTERCARE and CLEANING
• Always fill the tub with temperate water. Excessively hot water may cause surface damage
• Remove bath mat after use and hang to dry. Allowing bath mat to dry in the tub may cause surface damage.
• Clean after use with a mild liquid household detergent cleaner. Do not use Lestoil, Lysol Disinfectant (spray or
concentrate), or Lysol Basin, Tub and Tile Cleaner, Windex, Mr. Clean, Dow Disinfectant Bathroom Cleaner, or
cleaning products in aerosol cans.
HARSH CHEMICALS SHOULD NEVER BE USED ON ACRYLIC SURFACES.
• Do not use wire brushes, knives or sharp objects to remove stains, cigarette tar deposits, or other surface
blemishes.
• Abrasive cleaners or powders must not be used, since they will dull the surface. If the glossy surface looses
its sheen, dulled areas can be restored by rubbing with a white "automotive type" polishing compound and
waxing with a "liquid wax."
•Do not wax areas where you walk or stand.
• Do not allow nail polish remover, acetone, dry cleaning fluid, paint remover or other solvents to come into
contact with the surface.
• Clean the surrounding surface immediately after using caustic drain cleaners.
• Burning cigarettes will damage the surface.
• Should damage to the fixture occur, repairs can be made quickly and easily.
Your distributor or builder can provide details.