Kohler Empress Bouquet K-14223T User manual

BEFORE YOU BEGINBEFORE YOU BEGIN
ROUGHING-IN DIMENSIONSROUGHING-IN DIMENSIONS
NOTES
·
·
·
·
·
Use these instructions for above-counter installation.
Please follow the instructions that apply to your
installation.
You can choose between a wall-mount or countertop
faucet installation, depending upon the setting and styling
you desire. We recommended a wall-mount faucet.
Prior to installation, unpack the new lavatory and carefully
inspect it for damage. Return the lavatory to its protective
carton until you are ready to install it.
All information in these instructions is based upon the
latest product information available at the time of
publication. Kohler China reserves the right to make
changes in product characteristics, packaging, or
availability at any time without notice.
These instructions contain import care, cleaning, and
warranty information please leave these instructions for
the consumer.
·Kohler lavatory is made according to American National
Standard that it can match the American lavatory fittings.
Any other lavatory fittings may not fit for kohler lavatory.
·
·
·
·
·
·
-1-
Roughing-In Notes
Fixture dimensions are nominal and conform to tolerances
in ASME Standard A112.19.2M. (ASTMEA)112.19.2M
(T) Pop-up drain 229mm. (T) 229mm
(S) 356mm (Based on 305mm riser which may requing
cutting).
(S) 356mm 305mm
* Spout must be 127mm long (min.) for adequate clear-
ance into lavatory when installed with centerline as shown.
* 127mm ( )
** Spout must be tall enough to clear 76mm rim height and
provide a 25mm air gap per ASME A112.1.2
** 76mm ASME A112.1.2
25mm
Fig. #1
1
EMPRESS BOUQUET
INSTALLATION INSTRUCTIONS
VESSELS LAVATORY
K-14223T
(S)
(T)
3/8" HOT 102 102 3/8" COLD
1-1/4" OUTLET
**76
162
254
413
OF FITTING*
C
L
, 2010
Copyright Kohler China Ltd., 2010
528137
UNIT: mm
Length Width Height Depth
Outer 413 413 162
Inner 403 403 112
1148744-T01-A

TOOLS AND MATERIALS REQUIRED
(NOT SUPPLIED)
·
·
·
·
·
·
·
·
·
·
Sealant
Template (supplied)
Safety glasses
Pencil
Scissors
Tape Measure
Hole Saw
Keyhole saw or saber saw
Dill (1/2" dia. Drill bit, or larger)
Screwdriver
·
·
·
·
·
·
·
·
·
·
()
( 13mm )
-2-
Position the template on the
countertop.
Be sure to
provide sufficient spout overhang into
the lavatory basin. See the roughing-in
notes for minimum spout length
information.
Pay special
attention to the spout and handle fit
clearance when locating the faucet, as
noted below. Use the template to
locate the faucet spout hole centerline
on the countertop. This centerline is
recommended to provide adequate
clearance between the edge of the
lavatory and the spout.
Check for adequate clearance
between the backsplash or wall faucet
spout and handles, and lavatory. We
recommend clearance of at least
25mm between:
The installed lavatory and the
faucet spout
The installed lavatory and the end
of the faucet handles, and
The faucet spout and handles and
the backsplash or wall.
Refer to the faucet installation
instructions for required clearance, and
mark the preferred faucet hole
locations using a soft lead pencil.
Trace the template on the countertop
using a soft lead pencil.
For Wall-mount faucets:
For Countertop Faucets:
·
·
·
NOTE: In china installation will not
have separate backsplash. The back
wall is the "backsplash".
COUNTERTOP INSTALLATIONSCOUNTERTOP INSTALLATIONS
25mm
·
·
·
25mm Min.
Clearance
25mm
Spout
Centerline
Backsplash
Cut-out line
Outside Edge
of Lavatory
Fig. #2
2
1148744-T01-A

For tile, wood, or other porous
materials, apply waterproof sealant
around the cutout area of the
countertop surface. Follow all
manufacturer's instructions and
warnings. Allow the sealant to dry
before proceeding.
Use a 50/50 mixture of isopropyl
alcohol and water to clean the
countertop surface around the cutout
area. Wipe dry with a clean cloth.
: Install the adhesive sealant
when the temperature is at least 10 C.
The preferred temperature range to
apply the adhesive sealant is 21 C to
38 C.
Loosely apply the adhesive sealant
around the entire countertop cutout so
it is alongside the cutout hole. Adjust
the placement of the sealant before
removing the backing material. Cut off
any excess seal material. Carefully
remove the adhesive seal backing
material.
NOTE
o
o
o
50/50
10
21 38
Adhesive
Sealant
Fig.#4
4
Drill the faucet holes.
Install the faucet to the countertop according to the
manufacturer's instructions.
Install the drain to the lavatory according to the installation
instructions included with the drain. Apply a sufficient amount
of clear silicone sealant when you install the drain.
Fig.#3
3
Kohler
Cut out the opening by carefully
following the pencil line.
Large lavatories are very heavy.
Get help lifting the lavatory into
place.
Temporarily position the lavatory in the
countertop cutout so the "Kohler" logo
is visible. The logo is located inside the
basin, near the rim, and should be
positioned near the faucet.
Verify proper clearance between the
lavatory, faucet, and backsplash.
Remove the lavatory from the
countertop cutout, and return it to its
protective carton. Do not stand or store
the lavatory on the drain surface.
CAUTION: Risk of personal
injury or product damage.
-3-
1148744-T01-A

Nut
Gaskeet
Nut
Gasket
Fig.#6
6
Connect the faucet supply lines.
Connect the drain assembly.
Open the faucet valves, and check for
leakage.
Clean up with a non-abrasive cleaner.
IMPORTANT CONSUMER INFORMATIONIMPORTANT CONSUMER INFORMATION
CLEANING YOUR VESSELS LAVATORY
Keep your vessels lavatory looking new by rinsing it out
thoroughly after each use. Do not regularly use abrasives on
the lavatory surface, as this will eventually scratch and dull
the surface. For stubborn stains, abrasives may be used
sparingly.
THIS TAG IS FOR REMOVAL BY
HOMEOWNER ONLY!
Treat your decorative product just as you would treat your
fine china. The best way to clean it is to use warm water and
pat dry with a cotton cloth or soft sponge. use bristle
brushes or abrasive-backed sponges. They will scratch the
decorative surface.
For occasional cleaning of stubborn deposits, use ONLY the
following cleaners: apply the cleaner, wipe gently,
. Pat dry or wipe gently with a
cotton cloth.
DO NOT
rinse off
any residue immediately
USE&CAREUSE &CARE
-4-
CAUTION: Risk of personal
injury or product damage.
Large lavatories are very heavy.
Get help lifting the lavatory into
place.
Note the location of the "Kohler" logo.
The lavatory should be installed so the
logo is visible after installation.
Carefully position the lavatory in the
cutout, and press down firmly.
Fig.#5
5
Kohler Logo
Kohler
1148744-T01-A