Kokido Telsa 80 User manual
RECHARGEABLE CORDLESS CLEANER
USER MANUAL
ASPIRATEUR RECHARGEABLE SANS FIL
MANUEL D’EMPLOI
ASPIRADORA INALÁMBRICA RECARGABLE
MANUAL DE USUARIO
1
Table Of Contents
PARTS DIAGRAM P.4
SAFETY WARNINGS & INSTRUCTIONS P.5
GETTING STARTED P.7
Charging The Battery P.7
Set-Up Before Use P.9
Handle assembly P.9
Telescopic pole connector assembly P.9
Filter base unit assembly P.10
Telescopic pole (not included) assembly P.10
OPERATION P.11
EMPTYING THE FILTER BASE P.12
MAINTENANCE & STORAGE P.13
BATTERY DISPOSAL P.15
How to remove the battery pack P.15
TROUBLESHOOTING P.17
Remark: Product/parts photos in this manual are for demonstration only.
Product/parts in photos may vary with the model purchased.
2
Table des matières
DIAGRAMME DES PIÈCES P.18
AVERTISSEMENTS DE SÉCURITÉ ET
INSTRUCTIONS
P.19
DÉBUT DES OPÉRATIONS P.21
Chargement de la batterie P.21
Réglage avant l’utilisation P.24
Montage de la poignée P.24
Assemblage du connecteur de manche télescopique P.24
Montage de l’unité de base de filtre P.24
Montage du manche télescopique (non inclus) P.25
FONCTIONNEMENT P.26
VIDER LES DÉBRIS ET NETTOYER LA BASE P.27
MAINTENANCE ET STOCKAGE P.28
ÉLIMINATION DES BATTERIES P.29
Comment retirer le bloc de batteries P.30
REPÉRAGE DE PANNES P.32
Remarque : Les photos du produit/des pièces dans ce manuel sont
présentées uniquement à titre d’exemple. Le produit/les pièces peuvent
varier selon le modèle acheté.
3
Indice
DIAGRAMA DE LAS PARTES P.33
AVISOS E INSTRUCCIONES DE SEGURIDAD P.34
PRIMEROS PASOS P.36
Carga de la batería P.36
Montaje previo al uso P.38
Montaje del mango P.38
Ensamblaje del conector con la tapa trasparente P.39
Montaje de la unidad base del filtro P.39
Montaje de la pértiga telescópica (no incluido) P.40
FUNCIONAMIENTO P.40
VACIADO DEL LA BASE P.42
MANTENIMIENTO Y ALMACENAMIENTO P.43
ELIMINACIÓN DE LA BATERÍA P.44
Cómo retirar el paquete de baterías P.45
RESOLUCIÓN DE PROBLEMAS P.46
Observación: Las fotos de producto/piezas de este manual son sólo para
demostración. Producto / piezas en las fotografías pueden variar según el
modelo adquirido.
4
PARTS DIAGRAM
1 Rear body
2 Transparent lid
3 Telescopic pole
connector
4 Locking knob x2 (one
on each side)
5 Filter screen
6 Filter base
7 Draining filter plate
8 Suction nozzle flap
9 Draining flap
10 Wheels x 5
11 Bristles
12 Protective cap
13 Power ON/OFF button
14 Charger base
15 Draining holes (inside
handle chamber)
Battery : Rechargeable Li-ion battery pack, 4000mAH, 11.1V,
44.4Wh
Charging voltage :12.6V DC, 1000mA
Motor: 12V DC
16
Handle
5
SAFETY WARNINGS & INSTRUCTIONS
Read and follow all instructions in this manual and on the equipment. Failure to do so
could result in severe or fatal injuries.
WARNING!
-This is not a TOY. Children should be kept out of reach from this pool vacuum and
its accessories.
-Never allow children to operate this product.
-This pool vacuum is not intended for use by someone with reduced physical,
sensory or mental capabilities or a lack of experience and knowledge unless they
have been given instructions concerning the appliance and are under supervision
of the person responsible for their safety.
-Make sure the pool vacuum is fully immersed in the water before operation. The
minimum water level required to operate the device must reach above the power
button of the pool vacuum when it is held in a vertical position. Operating the pool
vacuum when it is not immersed in the water correctly could damage the unit and
void the warranty as a result.
-Maximum operating depth in water is 3 meters (10 ft).
-Maximum water temperature: 5˚C(41˚F) –35˚C(95˚F)
-DO NOT use power extension cords.
-Connect the external adaptor to a power source through a ground fault circuit
interrupter (GFCI). If in doubt, consult a qualified professional electrician.
-Do not use this pool vacuum if any damage is detected.
-Replace damaged parts as soon as possible. Only use parts certified by the
distributor or manufacturer.
-Turn off the power, disconnect the external adaptor from the power source, and
unplug the external adaptor from the charging base before detaching the pool
vacuum from the charging base.
-Disconnect the pool vacuum from the supply mains prior to carrying out user
maintenance such as cleaning the filter.
-Detach the pool vacuum from the charging base and make sure the pool vacuum
is OFF before servicing the product.
-Battery installed is a rechargeable Li-ion battery pack. Never attempt to replace
the battery pack.
-The pool vacuum is only to be used with the external adaptor delivered with this
product.
-You should not operate this pool vacuum when people/pets are present in the
water.
- DO NOT use this pool vacuum without an intact filter screen in place, as your
warranty will be voided as a result.
-Suction entrapment hazard: This pool vacuum generates suction. Do not allow
hair, body, or any loose parts of your clothing to make contact with the suction
hole of the pool vacuum during its operation.
-Never insert body parts, clothing or other objects into the openings and moving
parts of the pool vacuum.
-DO NOT use this pool vacuum to pick up any toxic substance, flammable or
combustible liquids such as gasoline, or in the presence of explosive or flammable
fumes.
6
-Never attempt in any way to disassemble this pool vacuum.
-Under no circumstances should you attempt to disassemble the pool vacuum and
replace the impeller, motor, and battery by yourself.
-Never insert any object to touch the impeller.
- External adaptor and charging base:
For indoor use only.
Never use the external adaptor and charging base for anything other than
charging the battery of the pool vacuum that is supplied in the same pack.
The external adaptor and charging base should not be used outdoors, nor
exposed to rain, humidity, any liquid or heat.
Keep the external adaptor and charging base out of reach of children.
Never use the external adaptor and charging base if any damage is
detected.
DO NOT handle the external adaptor and charging base with wet hands.
DO NOT handle the pool vacuum, external adaptor, and charging base
while charging with wet hands and without shoes.
Keep the external adaptor disconnected from power when it is not in use.
Never attempt to open the external adaptor and charging base.
If the supply cord is damaged, it must be replaced by the manufacturer, its
service agent or an equally-qualified person in order to prevent hazards of
any kind.
Make sure the pool vacuum and the charging base are completely dry
before charging.
CAUTION!
- This pool vacuum is designed for underwater use only; it is not an
all-purpose vacuum cleaner. DO NOT attempt to use it to clean anything
other than your pool / spa.
- Use only original accessories delivered with this product.
- DO NOT use this pool vacuum right after pool-shocking. It is
recommended to leave the pool circulating for at least 24-48 hours.
- It is not recommended to use this pool vacuum with another pool
vacuum/cleaner simultaneously.
- Avoid picking up hard, sharp objects with this product. They may
damage the pool vacuum and filter.
- Exercise caution when cleaning pool stairs.
- Only use the charging base for its intended purpose as outlined in this
manual.
- To avoid damaging the external adaptor and the cord, do not carry the
pool vacuum by the cord or pull the cord to disconnect it from the power
source and product.
- Charge the pool vacuum indoor in a clean, dry area with good ventilation
and an ambient temperature between 5˚C(41˚F) and 35˚C(95˚F).
- DO NOT leave the pool vacuum charged for over 20 hours.
- If the pool vacuum will not be used for an extended period, detach it from
the charging base and use a damp cloth to clean and dry the pool
vacuum and accessories. Make sure to charge the pool vacuum
completely before it is stored. Store in a well-ventilated area away from
sunlight, heat, ignition sources, pool chemicals, and children. Never
7
leave the pool vacuum plugged in for long-term storage. Recharge the
pool vacuum every three months.
Above warnings and cautions are not intended to incorporate all possible
instances for risks and / or severe injuries. Pool / spa owners should always
exercise extra caution and common sense when utilizing the product.
GETTING STARTED
IMPORTANT NOTE: Fully charge the pool vacuum before it is used for the first time.
Charging The Battery
WARNING!
Charging must be done indoors, in a well-ventilated area away from sunlight,
children, heat, ignition sources, and with an ambient temperature between 5˚C(41˚F)
and 35˚C(95˚F).
Never use the external adaptor and charging base if any damage is detected.
Use only the original external adaptor provided.
Make sure the pool vacuum and the charger base are clean and dry before set-up.
1. Turn the locking knob (on each side) anticlockwise until it points to the green dot
marking (unlock position) to unlock and release the rear body from the transparent lid.
2. Place the rear body (upside down - power on/off button face up) on a flat surface.
Open the protective cap on the rear body and align the 2 pins of the charger base
above the charging sockets. WARNING! Make sure not to invert the position of the
charger base. Press the charger base onto the rear body until it the pins are inserted
completely into the sockets. Plug the female jack of the external adaptor into the
charging port at the end of the charging base.
8
Important note:
Close the protective cap tightly after charging before operation
In case, charging sockets gets wet, dry the area completely (eg, using cotton bud)
before charging.
WARNING!
DO NOT handle the pool vacuum, external adaptor and charging base while it is
charging with wet hands and without shoes.
Connect the external adaptor to the power source through a ground fault circuit
interrupter (GFCI).
Charge the pool vacuum with the original external adaptor provided.
DO NOT use power extension cords.
Fully charge the battery before first use.
Charging must be done indoors, in a dry & well-ventilated area away from sunlight,
children, heat, ignition sources, and with an ambient temperature between 5˚C(41˚F)
and 35˚C(95˚F).
Always disconnect the external adaptor from the power source when charging is
complete.
Do not leave the pool vacuum in charge for over 20 hours.
Immediately turn the power off and disconnect the external adaptor from the power
source if you detect any of the following conditions:
- Offensive or unusual odor
- Excessive heat
- Deformation, cracks, leaks
- Smoke
1. Make sure that the pool vacuum is turned off prior to charging.
2. Connect the external adaptor to the power source. Once the pool vacuum begins
charging, the indicator light on the external adaptor will turn red. Normally, it takes
about 5-6 hours to reach a full charge. The indicator light will turn green when the pool
vacuum is almost fully charged.
Note: If the motor is generating noise, immediately turn off the device by pressing the
ON/OFF button. Otherwise, it could potentially lead to failure of the shaft seals / motor,
and the warranty will be voided as a result.
Note: Charge the pool vacuum completely (about 5-6 hours) prior to first use.
3. When charging is complete, disconnect the external adaptor from the power source
and unplug the jack from the charging base.
4. Detach the charging base from the pool vacuum.
Normally the pool vacuum can be operated up to 45 minutes on a full charge
(charged for about 5-6 hours)
9
To re-position the transparent case (with the filter cone inside) to the rear body, make
sure the locking knob on both sides is turned to the unlock position. Align the raised
arch on both sides of the transparent case with the locking knobs and then turn the
knob clockwise until it points to the red marking to secure the assembly.
Attention: The case has one correct position only. The water-draining valve must be
facing the bottom when holding the cleaner horizontally by the handle.
FACT: Rechargeable lithium-Ion battery is classified as a consumable item. It has a
limited life and will gradually lose its capacity to hold a charge. Therefore, running
time of the pool vacuum will gradually reduce through repeated charging and
discharging in operation.
NOTE: Let the pool vacuum rest for around 30 to 40 minutes before charging it again.
Set-Up Before Use
Handle assembly
Insert the handle into the pool vacuum as shown, until the side pin on the handle is
secured to the handle’s locking hole on the rear body.
To release the handle, press down on the side pin and pull out the handle.
Telescopic pole connector assembly
Pull to detach the locking pin from the pole connector. Align the holes on the front
arms of the pole connector to the holes of the hinge on the transparent lid. Insert the
locking pin through all the holes in order to secure the pole connector on the lid.
10
Filter base unit assembly
First, place the dome filter screen onto the base. Then, place the transparent lid on
top and align both orange line markings. Make sure the flange of transparent lid is not
resting on any of the arches of the base.
Push on the tab to turn the transparent lid in the same direction as the red arrow
(anticlockwise) until all tabs reach the arches and lock the transparent cover in place.
Align and insert all brushes into the notches on the underside of the cleaner.
Align and insert the wheels into the cavities on the underside of the cleaner.
Telescopic pole (not included) assembly
Note:
1. A V-clip is installed inside the pole connector to secure the telescopic pole in
position.
11
2. Make sure to assemble the handle. You need to hold it as well while putting the
pool vacuum into pool water or lifting it out of the pool.
Press the button of the V-clip to retract the side tabs and then slide the telescopic pole
onto the pole until the side holes of the telescopic pole match the side tabs. Release
the V-clip button and the telescope pole is secured to the pole connector.
To release the telescopic pole, press the V-clip button and pull the pole away from the
cleaner.
OPERATION
WARNING!
Do not use the pool vacuum if any damage is detected.
Oil stain could occur due to possible leakage of lubricants applied to the O-ring.
Do not operate this pool vacuum if there are people/pets present in the water.
Make sure the pool vacuum is fully immersed in the water before initiating operation.
The minimum water level required to operate the device must reach above the
power button of the pool vacuum when it is held in a vertical position. Operating the
pool vacuum when not immersed in the water correctly can damage the unit and
the warranty will be voided as a result.
Maximum operating depth in water is 3 meters (10 ft).
Maximum water temperature: 5˚C(41˚F) –35˚C(95˚F)
DO NOT use the pool vacuum without an intact filter screen in place. Using your
pool vacuum without an intact filter screen in place will VOID your warranty.
Suction entrapment hazard: This pool vacuum generates suction. Do not allow hair,
body or any loose parts of your clothing to make contact with the suction mouth of
the pool vacuum during its operation.
Never insert body parts, clothing or other objects into the openings and moving
parts.
DO NOT use this pool vacuum to pick up any toxic substance, flammable or
combustible liquids such as gasoline, or operate in the presence of explosive or
flammable fumes.
DO NOT cover the side slot of the vacuum during operation. The impeller/motor
may be damaged as a result.
Never insert any object to touch the impeller.
CAUTION
Use only original accessories delivered with this product.
DO NOT use this pool vacuum immediately after pool-shocking. It is recommended
to leave the pool circulating for at least 24-48 hours.
12
It is not recommended to use this pool vacuum with another pool vacuum/cleaner
simultaneously.
DO NOT leave the pool vacuum in the water when it is not in use or when battery is
low as water leakage may occur.
1) Bring your pool vacuum to the side of your pool / spa. Immerse the pool vacuum in
water and press the power button to initiate operation.
CAUTION! Make sure the pool vacuum is always facing downwards when it is placed
into the pool. Otherwise it may bend the pole connector and damage it during the
process. Make sure to assemble the handle as well. Hold both the handle and
telescopic pole simultaneously to place the pool vacuum into water.
2) To remove the pool vacuum from the pool / spa, lift the pool vacuum while pointing
it downwards in order to allow water to escape from the outlet valve. Water is going to
escape via the handle / pole connector and draining holes inside the handle chamber
on the rear body.
CAUTION! Make sure the pool vacuum is always facing downwards when it is
removed from the pool. Otherwise, the pole connector may be bent and damage the
pool vacuum in the process. Make sure to hold the handle as well when lifting the pool
vacuum out of the water.
3) Rinse the pool vacuum with fresh water after every use. DO NOT use any
detergent.
EMPTYING THE FILTER BASE
WARNING! Using the pool vacuum without a filter screen in place will VOID
your warranty.
In order to maximize the cleaning efficiency, be sure to clean the filter cone before
and after each use.
CAUTION! If the pool vacuum is charging, disconnect the external adaptor from the
power source and detach the pool vacuum from the charging base.
Emptying filter base
1. Place the pool vacuum on a stable surface.
2. Release the rear body from the transparent lid.
3. Push on and rotate the tabs on the transparent round cover clockwise until the
orange bar on the transparent cover and the base are aligned. Lift the transparent
cover off the base. Hold the small grips on the top of the filter cover to lift it off the
base and gain access to the debris.
13
4. Clean out all debris from the base, suction nozzle flap, and draining filter plate.
Use clean water to rinse the entire base. To detach the filter plate, pry the rib of the
plate. If the draining filter plate is damaged, replace it with a new one before the
next operation.
Note: Do not remove the draining filter plate. Without it, debris will escape from the
base’s debris compartment during operation.
5. Reverse the steps to install the filter and cover onto the base. Make sure the flange
of the transparent cover is under the arch.
MAINTENANCE & STORAGE
NOTE:
1. Battery discharges on its own during storage. Make sure to fully-charge the pool
vacuum before storage.
2. You must re-charge the battery at least once every three months when it is not in
use.
Unplug the external adaptor from the socket and then unplug the adapter jack from
the charging base.
14
Detach accessories from the pool vacuum. If necessary, rinse the pool vacuum and
accessories with fresh water. DO NOT use detergent.
Make sure to drain the water from the rear body through the holes located inside
the chamber that connects to the handle/ pole connector, and the hole on the rear
of the body.
Make sure to drain the water from the handle through its hole on the bottom end.
Use a damp cloth to clean and dry the pool vacuum and its accessories.
Store them in a well-ventilated area away from sunlight, heat, ignition sources, pool
chemicals and from children. Ambient temperature for storage should be 10˚C –
25˚C (50˚F – 77˚F). NOTE: A higher storage temperature may reduce the battery
life.
WARNING!
-Never attempt in any way to disassemble the pool vacuum.
-Under no circumstances should you attempt to disassemble the pool vacuum and
replace the impeller, motor and battery by yourself.
-To replace a damaged wheel, pull/push it out from the cavity. Press the new wheel
into the cavity.
CAUTION!
Excessive heat can damage the battery and reduce its lifespan as a result.
The battery supplied with your pool vacuum lasts for about 300 charging cycles
(with proper charging and operation). Life span of battery is reduced if the following
happens:
- Battery appears damaged or will not charge fully.
- Battery operation time is noticeably reduced. Observe and note the
operation time during the first few uses (on a full charge). Use this
information as a reference point to compare operation time with older
batteries.
The battery must be removed from the pool vacuum before it is disposed of.
The pool vacuum must be disconnected from the supply mains while removing the
battery
The battery is to be disposed of safely and according to local ordinances or
regulations.
NOTE: Incorrect maintenance may reduce the battery life and affect its capacity as a
result.
15
BATTERY DISPOSAL
Your pool vacuum is equipped with a maintenance-free rechargeable lithium-ion
battery pack, which must be disposed of properly. Recycling is required; please
contact your local authority for more information.
WARNING!
Never attempt to disassemble a battery pack
Remove all personal items such as rings, bracelets, necklaces and watches when
the battery pack is unwired from the pool vacuum.
A battery can produce a short circuit current high enough to weld a ring (or similar
item) to metal, causing a severe burn in the process.
Wear complete eye protection, gloves and protective clothing when the battery
pack is being removed.
Avoid touching the wires altogether and avoid allowing them to make contact with
any metal items, which could cause sparking and/or short circuit the battery.
Never smoke or allow a spark or flame in the vicinity of the battery or the pool
vacuum.
Do not expose the battery to fire or intense heat as this may result in an explosion.
CAUTION!
If a battery leak occurs, avoid contact with the leaking fluids and place the damaged
battery in a plastic bag.
-If leaking fluids come in contact with skin and clothing, wash immediately with
plenty of soap and water.
-If leaking fluids come in contact with eyes, do not rub eyes, immediately flush eyes
with cool running water for at least 15 minutes and do not rub them. Seek medical
attention as soon as possible.
How to remove the battery pack
Recommended tools (not included): Philips Screwdriver.
1. Turn the locking knob (on each side) anticlockwise until it points to the green dot
marking (unlock position) to unlock and release the rear body from the transparent lid.
2. Use the screwdriver to unscrew the 4 screws located on the top plate and then
detach it from the rear body to expose the rear body’s cover.
16
3. Unfasten 6 screws and detach the cover to expose the PCBA, motor assembly,
and battery pack.
4. To detach the battery connection wire, press the clip on the connector and then pull
it out. NOTE: Wrap the connector immediately with insulating tape in order to avoid
short circuit caused by contact of both wire terminals.
5. Unfasten the 3 screws to release the battery compartment cover. Remove battery
pack from the compartment.
17
TROUBLESHOOTING
Problem Possible Cause Solution
Pool vacuum does not capture
the debris
Battery is running out Charge the battery again.
Impeller is jammed Power off the pool vacuum and visually check
the gap in middle of the pool vacuum to see if
the impeller is jammed by larger debris. If
possible, use a small tool to remove it with
intensive care & caution. If necessary,
contact your dealer for further instructions.
WARNING! Make sure the pool vacuum is
powered off when the unit is being serviced
.
Impeller is broken Contact your
dealer for impeller replacement.
Filter base is full Clean the filter base .
Larger debris / large
volume of debris
Remove the brushes from the filter base
bottom
Debris escapes from the filter
base
Suction nozzle flap is
broken
Suction nozzle flap works like a door to
prevent the debris from escaping from the
filter. Contact dealer for replacement parts
and instruction.
Draining filter plate is
damaged
Replace with a new draining filter plate.
Handle / pole connector
cannot be secured in
assembly
Side pin is broken Replace with a new handle / pole connector.
Pool vacuum cannot be
charged / recharged
Battery is damaged Contact dealer for battery replacement.
WARNING! DO NOT open the pool vacuum
and replace the battery by yourself. This
could result in severe or fatal injuries and the
warranty will be voided as a result.
Contact plates of the
charger base and unit
are not connected.
Make sure that the charger base is
assembled on the unit properly so that their
contact plates are touching.
External adaptor is out of
order
Contact dealer for replacement.
WARNING! Using the wrong external adaptor
will result in damaging the pool vacuum /
battery and voiding the warranty as a result.
Cleaner does not move
smoothly
Wheel is jammed/
damages
Clean the wheels. Replace damage wheels.
Brushes underneath is
damaged
Replace damaged brushes
© 2016 Kokido Development Ltd.
All rights reserved. No part of this document may be reproduced or transmitted in any form or by any
means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of
Kokido Development Ltd. (V2)
If soft copy of this instruction manual is required, please contact our customer service by email:
18
DIAGRAMME DES PIÈCES
1 Corps arrière
2 Couvercle transparent
3 Connecteur de manche
télescopique
4 Bouton de verrouillage
x2 (un de chaque côté)
5 Crépine
6 Base de filtre
7 Plaque filtrante de
purge
8 Volet de tuyère
d’aspiration
9 Clapet de refoulement
10 Roulettes x 5
11 Brosses
12 Capuchon protecteur
13 Bouton marche/arrêt
14 Base de chargeur
15 Orifices d’évacuation (à
l’intérieur de la
chambre de la poignée)
Batterie : Bloc de batteries à lithium rechargeables, 4000 mAH,
11,1 V, 44,4 Wh
Tension de charge : 12,6 V CC, 1000 mA
Moteur : 12 V CC
16 Poignée
19
AVERTISSEMENTS DE SÉCURITÉ ET INSTRUCTIONS
Lire et suivre toutes les instructions figurant dans ce manuel et sur l’équipement. Ne
pas le faire pourrait donner lieu à des blessures graves ou mortelles.
AVERTISSEMENT !
-Ceci n’est pas un JOUET. Les enfants doivent être maintenus hors de la portée de
cet aspirateur de piscine et de ses accessoires.
-Ne jamais permettre aux enfants de faire fonctionner ce produit.
-Cet aspirateur de piscine n’est pas prévu pour être utilisé par quelqu’un avec ses
capacités physiques, sensorielles ou mentales diminués, ou un manque
d’expérience et de connaissances à moins d’avoir reçu des instructions
déterminées relatives à l’appareil et sous la supervision de la personne
responsable de leur sécurité.
-S’assurer que l’aspirateur de piscine est totalement immergé dans l’eau avant
l’exécution du travail. Le niveau d’eau minimum requis pour faire fonctionner le
dispositif doit dépasser le bouton d’alimentation de l’aspirateur de piscine lorsqu’il
est tenu dans une position verticale. Faire fonctionner l’aspirateur de piscine
lorsqu’il n’est pas immergé correctement dans l’eau peut endommager l’unité et
annuler de ce fait la garantie.
-La profondeur maximale de fonctionnement dans l’eau est de 3 mètres (10 pieds).
-Température maximale de l’eau : 5˚C– 35˚C
-Ne pas utiliser de rallonges de câble électrique.
-Brancher l’adaptateur externe à une source d’alimentation à travers un disjoncteur
différentiel de fuite à la terre (DDFT). En cas de doute, consulter un électricien
professionnel qualifié.
-Ne pas utiliser cet aspirateur de piscine si un dommage quelconque est détecté.
-Remplacer les pièces endommagées le plus rapidement possible. N’utiliser que
des pièces certifiées par le distributeur ou le fabricant.
-Mettre hors tension, débrancher l’adaptateur externe de la source d’alimentation,
et débrancher l’adaptateur externe de la base de chargement avant de séparer
l’aspirateur de piscine de la base de chargement.
-Débrancher l’aspirateur de piscine de l’alimentation principale avant de réaliser la
maintenance d’utilisateur telle que le nettoyage du filtre.
-Retirer l’aspirateur de piscine de la base de chargement et s’assurer que
l’aspirateur de piscine est hors tension avant la mise en service du produit.
-La batterie installée est un bloc de batteries rechargeables au lithium. Ne jamais
tenter de remplacer le bloc de batteries.
-L’aspirateur de piscine ne doit être utilisé qu’avec l’adaptateur externe livré avec
ce produit.
-Vous ne devrez pas faire fonctionner cet aspirateur de piscine lorsque des
personnes/animaux de compagnie sont présents dans l’eau.
- Ne pas utiliser cet aspirateur de piscine sans une crépine en place, car votre
garantie serait annulée de ce fait.
-Danger de piégeage de l’aspiration : Cet aspirateur de piscine produit une
aspiration. Ne pas permettre que les cheveux, le corps, ou toutes parties lâches
de vos vêtements entrent en contact avec l’orifice d’aspiration de l’aspirateur de
piscine pendant son fonctionnement.
-Ne jamais introduire des parties du corps, vêtements ou autres objets dans les
Table of contents
Languages:
