Konig & Meyer 19745 User manual

INSTALLATION INSTRUCTIONS (A-F)
19745 Smartphone holder
- Universal holder suitable for all devices with a width 46-84 mm
- Particularly suitable for smartphones, flat devices and MP3 players
- Functioning of the operating controls is not affected
- Simply place in the holder and close the clamping jaw
- Released at the press of a button
- Moveable bars can be removed and the holder turned
- Smartphone operating controls are almost freely accessible -
-and if not: turn the holder 180° and mount it
- 4 different holding arms adjust to any Smartphone
- Clamps on tube diameters 7 - 30 mm
- Flexible holding arm (length 110 mm) for positioning as required
SAFETY NOTES
- Use a suitable stand - the stand must be stable, able to accommodate the weight and have a tube ø 7-30 mm; e.g. K&M music stands (100/1 et seq.),
-for orchestral stands (118/1 et seq.) and
-microphone stands (200 et seq.), etc.
- Carefully place the smartphone in the holder and
-ensure it is held firmly in place
- Maneuver the holder with care; when adjusting we recommend first
-removing the smartphone and replacing it when adjustment is completed
Thank you for choosing this product. These instructions contain information about the installation and use of the holder. We suggest you keep the
instructions in a safe place for later use.
APREPARE THE STAND (see Safety Notes above)
BLAY OUT THE COMPONENTS for 19745 IN ORDER
B1Four holding arm pairs (2 heights, D depths)
B2Smartphone cradle
B3Holding arm with clamp (for tubes 7-30 mm)
CCONNECTING THE SMARTPHONE CRADLE TO THE HOLDING ARM
C4Place the smartphone cradle on the four hooks
C4of the holding arm plate...
C4.a. The smartphone cradle can be turned 180°,
C4.a. if needed (e.g. because of the connections/cables)
C4.b. NOTE: the holding arms must always be mounted
C4.b. NOTE: in the lower position: refer to Section 10.
C5…and then slide the holding plate in the "close"
C5direction against the smartphone cradle until it
C5audibly clicks in place.
C6The correct position has been reached
C6when the holding plate sits firmly on the
C6side marked with "close".
DATTACHING THE HOLDING ARM TO THE STAND TUBE
D7Hold the holding arm clamp on the stand tube
D7(7-30 mm) and attach by tightening the
D7knurled screw.
D8The knurled screw has a removable
D8protective plastic cap to protect the
D8surface of the tube (part no. 01-86-865-55).
EPLACING THE SMARTPHONE IN CRADLE
ENOTE:
ESuitable for devices with a width 46-84 mm
E19Press the button to part the sides
E10.a Select the correct holding arms (4 options)
E10.b Slide both holding arms in the corresponding
E 10.b. slots on the side of the smartphone cradle.
E10.c The two lower bars can be slid to the right or left -
E 10.c accommodating a variety of smartphones.
E 10.c NOTE:
E 10.c The bars can be removed to aid installation.
E 10.c We stress the importance of BOTH bars being
E 10.c in place when the device is clicked in the cradle.
E11.a Hold the smartphone with one hand and position
E 11.a centrally on the lower bars of the cradle…
E11.b …then close the two sides with the other
E 11.b hand until the device is held firmly between
E 11.b the moss rubber protectors.
B
C
D
E

INSTALLATION INSTRUCTIONS (A-F)
Continuation
19745 Smartphone holder
FREMOVING THE SMARTPHONE FROM THE CRADLE
F12 Hold the smartphone at the top...
F13 ...with the other hand press the sliders
F13so that the side bars part and...
F14 ...the smartphone can be removed.
GSTAND:
- Tube diameter 7-30 mm
HSIZE SMARTPHONES:
- Width: 44-84 mm
- Height: check suitability above 150 mm
- if need check to see that it fits correctly
IDIRECTION:
- 360° around the clamp on the stand tube
JTILT (see Fig.):
- The flexible arm can be "bent" through 90°.
-Apply gentle strength.
-We recommend: bending the arm upwards for a good reading angle
-We do not recommend: bending the arm sideways as this is better
- We do not recommend: attained by re-adjusting the clamp.
-We warn against: bending the arm downwards as the smartphone
- We warn against: may fall from the holder.
KFORMAT (see Fig.):
K- Portrait (vertical)
K- Landscape (horizontal)
K- The arm is connected to the cradle and u clamp in two ways:
K-a. per screw mechanism
K-b. per square plug connection
K15 Switching from portrait to landscape format and back
K14functions as follows.
K14aLoosen and remove the arm union nut (it doesn‘t
K14amatter which one of the two)
K14bRemove the arm
K14cTurn the arm through 90° and insert the cone in the
K14csquare plug of the threaded connection
K14dRe-tighten the union nut
FAULT-FINDING (F) and REPAIR (R)
F: Smartphone wobbles
F: B: Check the side bars are tight and
F: B: if necessary correct (E 11.b)
F: Smartphone cradle wobbles
F: B: Check the screw connections and if necessary tighten (15)
F: B: Locking mechanism not right? Repeat positioning
F: B: procedure for the cradle and ensure it is correctly
F: B: locked in place (C)
FUNCTIONS & ADJUSTMENT (G-K)
F
GH
I
J
K
Material
Clamp, knurled screw: steel
Cradle, holding plate, nuts: PC-ABS
Arm: aluminum bar internally,
Arm: plastic externally
Knurled handle, tappet: PA
Load Smartphones, MP3 players,
div. devices (pay attention to size)
TECHNICAL DATA
KÖNIG & MEYER GmbH & Co. KG
Kiesweg 2, 97877 Wertheim, www.k-m.de
19745-015-55 Rev.01 03-80-269-00 12/14
Dimensions Width of device: 44-84 mm
for tubes: ø 7-30 mm
Carton 155 x 50 x190 mm
Weight net: 0.19 kg
gross: 0.27 kg