KONWA KW-123L User manual

KONWA®
KW-123L
END CUTTER
INSTRUCTION MANUAL
&
PARTS LIST

INSTRUCTIONS
Before using this cutter, please read all the instructions carefully.
A. ASSEMBLY
1. Please assemble the cutter based on the pictures provided.
2. Choose the right power supply and use the socket with earth-wire for safety.
3. Please make sure the rail inside is cleaned when first operate the cutter.
B. REPLACING THE BLADE AND CARBON BRUSH
1. Blade : Blade must be replaced when it wears to 3-4mm. Be sure the front face of the
knife when re-setting the knife. Knife that having words must be facing in front.
2. Carbon Brush : When the motor is not running well, should stop and check the carbon
brush. Carbon brush should be replaced when it wears to 5-6mm.
C. SERVICING
Grinding Wheel : To keep the stoning effective, grinding wheel must be removed or
changed when it is too much greasy dirt.
After long time operation, should clear the rail inside and the lower knife of the cutter to
keep the cutter run smoothly.
D. CAUTIONS
1. When the cutter is running, please make sure that there is nothing put on the rail or
track of the cutter (except the cloth should be cut in the correct place).
2. Should adjust the height of the safe guard of the cutter according to the height of the
cloth.
3. Before servicing and repairing the cutter, please make sure the power is off.
4. Connect earth wire for safety.
5. The operator should keep their palm dry.
SPECIFICATIONS
Side of blade : 108mm
Shape of the blade : Round
Electric pressure : Single phase, 240V, 50Hz
Revolving speed of the knife : 14000r.p.m.
Output : 123W

Part No. Description Part No. Description
1 Motor Housing 32 Spring
2 Stator 33 Grind Button
3 Bearing 34 Screw
4 Collar 35 Screw
5 Rotor Assembly 36 Blade
6 Carbon Brush 37 Washer
7 Cap for Carbon Brush 38 Nut
8 Screw for Stator R39 Screw
9 Front Cover for Motor R40 Face plate
R10 Screw R41 Safe Guard
R11 Socket R42 Screw
R12 Screw 45 Balance Block
R13 Terminal Box Cover 46 Nut
R14 Counter 47 Sphericity Nut
R15 Terminal Box 48 Screw
R17 Handle 49 Lower Knife Base
R18 Switch Cover 50 Screw
R19 Switch 51 Lower Knife
R20 Switch Box Cover 52 Base plate
R21 Screw 53 Spring
R22 Screw 54 Screw
23 Screw 55 Collar
24 Screw 56 Bearing
25 Washer 57 Washer
26 Grind Wheel Base 58 Shaft
27 Grind Wheel 59 Plug
28 Bearing 60 Cord Clamp
29 Copper Collar 61 Fix Screw
30 Collar 62 Clamp Screw
31 Grind Wheel Front Base 63 Clamp Nut

Part No. Description Part No. Description
68 Spring 78 Screw
69 Spring Protector 79 Nut
70 Orbit 80 Clothing Winder Holder
71 Screw 81 Stopper
72 Nut 82 Screw Value
73 Rubber Press 83 Screw
74 Inner Plate in the Orbit 84 Position Sleeve
75 Belt 85 Cord Holder Base
76 Return Spring 86 Cord Holder Assembly
77 Plastic Stopper

Part No. Description Part No. Description
101 Screw 140 Screw
102 Bearing 141 Nut
103 Washer 142 Lift Level
104 Base 143 Screw Pin
105 Collar 144 Washer
106 Cap 145 Nut
107 Screw Value 146 Long Spring
108 Cord Holder Base 147 Screw
109 Nut 148 Nut
110 Spring Screw 149 Press Block
112 Spring 150 Screw
113 Screw 151 Position Screw
114 Nut 152 Nut
115 Washer 153 Screw Pin
116 Spring Pin 154 Fix Sleeve
117 Shaft Pin 155 Nut
118 Move Plate 156 Lift Level
119 Collar 157 Screw Pin
120 Steel Tube 158 Lift Handle
121 Rubber Sleeve 159 Nut
122 Plastic Tube 160 Lift Slider
123 Cord Clamp 161 Chain
130 Pin 162 Screw
131 Wheel 163 Nut
132 Nut 164 Nut
133 Orbit Holder 165 Orbit Lift Base
134 Screw 166 Screw Value
135 Nut 167 Nut
136 Lift Lever 168 Wheel
137 Collar 169 Bearing
138 Pin 170 Collar
139 Wheel Base 171 Screw Pin

KONWA®
KONWA INDUSTRIAL SEWING MACHINE (M) SDN BHD (124740-M)
Head Office: Lot 11 & 13, Jalan 51/201, Off Jalan Tandang, Seksyen 51, 46050 Petaling Jaya,
Selangor Darul Ehsan, Malaysia.
Tel: [phone] Fax: [phone]
E-mail: [email protected] URL: www.konwa.com.my