FEATURES
This ten-bottle wine cooler is designed to accept 750 ml bottles up to 315mm (12.5") tall.
The temperature settings are between 10°C (50°F) and 1 °C (66°F). Temperature selection,
ºC or ºF, switchable. Interior light operated by external switch.
SAFETY
- This unit is an indoor appliance. DO NOT use OUTDOORS.
- Household Use Only
- There must be at least 127 mm (5”) clearance around the unit to ensure proper ventilation.
- Place unit on a flat surface, away from heat sources
- Do not use the appliance if the plug or cable is damaged. If the power cord is damaged
and/or is malfunctioning, please contact the manufacturer.
- Pull the plug out of the outlet to disconnect. DO NOT pull the cord.
- Do not touch the plug with wet hands.
- Unplug the appliance when not in use.
Use of extension cords
Because of potential safety hazards under certain conditions, we strongly recommend against
the use of an extension cord. However, if you must use an extension cord, it is absolutely nec-
essary that it is a UL-listed (in the United States) or a CSA-listed (in Canada), 3-wire ground-
ing type appliance extension cord having a grounding type plug and outlet and that the electri-
cal rating of the cord is 15 amperes (minimum) and 120 volts.
SPECIFICATIONS
Power Requirements: AC 120V 60Hz 50W
Capacity: 10 x 750 ml (25.4 oz) bottles
Max. Temp.: 1 °C +/- 3°C (66°F +/- 5°F) at 22°C (72°F) ambient air temp.
Min. Temp.: 10°C +/- 3°C (50°F +/- 5°F) at 22°C (72°F) ambient air temp.
Weight: 10.3 kg (23 lbs)
INSTALLATION
• Choose a location where there is an electrical outlet within reach of the power cord. There
must be at least 127 mm (5”) clearance around the unit to ensure proper ventilation.
• Locate the Wine Cellar away from direct sunlight and sources of heat (stove, heater,
radiator, etc.). Direct sunlight may affect the acrylic coating and heat sources may increase
electrical consumption. Extreme cold ambient temperatures may also cause the unit not to
perform properly. Avoid locating the unit in moist areas.
• Plug the Wine Cellar into an exclusive, properly installed-grounded wall outlet. Do not
under any circumstances cut or remove the third (ground) prong from the power cord. Any
questions concerning about power and/or grounding should be directed toward a certified
electrician or an authorized products service center.
OPERATING INSTRUCTIONS
1. Insert the power plug into the power socket. Make sure the power socket is 110-120V
AC/60Hz.
2. Set the desired cooling temperature by pressing the buttons or to set your desired
temperature. Each depression of the buttons will scroll through the available temperature
settings. Numbers will flash while setting. Solid numbers indicate the current internal
temperature in Celcius or Fahrenheit. Switch to your preference using the °C to °F switch.
3. Allow the empty Wine Cellar to operate for approximately 3 hours. This will allow it to
reach the desired temperature.
4. Fill the wine cooler with your choice of wine bottles. Allow 24 hours of operation before
the bottles reach the desired temperature.
5. The right touch control button operates both the interior light and switches the temp. dis-
play from Celcius to Fahrenheit. Touch once to turn the interior light on or off. To switch
between Celcius and Fahrenheit, hold button for 4 seconds.
The Wine Cellar should be placed where the ambient temperature is between 59°F to 77°F
(15°C to 25°C). If the ambient temperature is above or below this range, the performance of
the unit may be affected. For example, placing your unit in extreme cold or hot conditions
may cause interior temperatures to fluctuate.
RECOMMENDED TEMPERATURES FOR CHILLING WINE
Red Wines: 15-1 °C (5 -66°F)
White Wines -15°C (46-57°F)
The above temperatures may fluctuate depending on whether the interior light is ON or OFF
or the bottles are located on the upper/middle/lower section.
MAINTENANCE
• Clean the interior using mild detergents or glass cleaning products.
• NEVER use harsh detergents or solvents.
• DO NOT immerse in water.
• Periodically, empty the tray of accumulated condensation located at the back of the unit.
