KOTT Es-Link KCU2000 User manual

USER MANUAL
Es-Link KCU2000
`
Korea One Telecommunication Technology, Inc
Before you begin
This manual of Es -Link KCU2000 ADSL Modem designed for general user is

2
included from introduction to installation of ES-LINK KCU2000.
Before starting, you should read this manual carefullyforthesuccessfulprocessing.
For further information, contact the customer service in KOTT
E-mail: [email protected]
Copyright(C) 2001 by Korea One Telecommunication Technology
All Rights Reserved. Reproduction or media conversion by any means is protected by
copyright and may only occur with prior written permission of KOTT
Table of contents
1. Introduction --------------------------- 5
Es-Link KCU2000 Modem Introduction --------------- 6
Es-Link KCU2000 Specifications ----------------- 6
2. Setting Driver ------------------------- 7
Setting Driver---------------------------------- 8

3
For Windows 98(98SE) --------------------------- 8
For Windows 2000 ------------------------------- 11
Checking the installation of Modem -------------- 14
Configuring VPI / VCI ------------------------- 16
3. Internet Access ------------------------ 18
3-1. PPPoE Protocol ----------------------------- 19
Installing EnterNet 300 ---------------------- 19
Installation in Win 98(98SE)/2000 ----------------- 19
3-2. Connecting to Internet--------------------- 24
Installing with EnterNet 300 ------------------- 24
3-3. PPPoA Protocol ---------------------------- 27
Installing and connecting in Windows 98(98SE) --- 27
Installing and connecting in Windows 2000----- 32
4. Remove Modem Driver ------------------- 37
Windows 98(98SE) ------------------------------ 38
Windows 2000 ---------------------------------- 40
Product Warranty -------------------------- 42
1. Instruction
lEs-Link Es-Link KCU2000 Modem Instruction
lEs-Link Es-Link KCU2000 Modem Specifications

4
Es-Link KCU2000 Modem Instruction
The Es-Link KCU2000low-power USB-based ADSL chipset and PC driver
solution is optimized to address the growing demand for high-speed
Internet access. The Es-Link KCU2000 is a controllerless solution that is
fully compliant with both the full-rate ADSL (G.992.1 and G.dmt) and the
'splitterless' G.lite (G.992.2) standards. It uses Conexant solution.
The Es-Link KCU2000 modem is an always on high-speed broadband
connection to the Internet. Using existing twisted pair telephone lines, ADSL
technology provides data rates over 100 times the speed of a traditional
analog modem, without an interruption in telephone service. With up to 8
Mbps downstream and 1 Mbps upstream data transfer rates, ADSL is the
ideal solution for high-bandwidth applications such as access to a corporate
network, Internet access, and video on-demand.
Es-Link KCU2000 Modem Specifications

5
Size 9Cm * 12Cm
Chip set Conexant Chipset
Interface Standards USB
ANSI T1.413 Issue2
ITU-T G.992.1 (G.DMT)
Protocol ITU-T G.992.2 (G.Lite)
Full-rate Downstream 8Mbps, upstream 1Mbps
Transmission Speed G.Lite Downstream 1.5Mbps,Upstream 512Kbps
Transmission Distance 18,000ft(approximately 5.5 Km)
Transmission standardsFull PPP (RFC 2364),Multi Protocol (RFC 1483)
2. Setting Driver
lSetting Driver
-For Windows 98(98SE)
-For Windows 2000
lChecking the Modem Installation.
lConfiguring VPI / VCI

6
Setting Driver
If you want to use a modem in a PC, driver must be installed firstly.
Before you start this chapter, prepare driver diskette provided with a modem and
check your PC OS(Operating system) and setup.
Es-Link KCU2000 is compliant with PnP(Plug and Play) and easy to install.
Put the modem in a PC and turn it on as previous chapter, and Windows will
recognize modem automatically.
For Windows 98(98SE)
1. Turn on the PC.
Click "Next”

7
2. Click “Next”after checking <Search for the best driver for your device
(Recommended)> chosen.
3. Check <Specify a location>and find a installing driver fromBrowse.

8
4. Click “Next”after checking <Location of driver>
5. Click “Finish”

9
For Windows 2000
1. Turn on the PC.
Click "Next”
2. Click “Next”after checking <Search for a suitable driver for my device
(Recommended)> chosen

10
3. Check <Specify a location > and click “Next”.
4. Click “OK”after selecting a location of driver from “Browse”
5. Click “Next”