kozy heat Northern Firelights PFT-40 User manual

WARNING: For Outdoor Use Only
SEPT 2013
PFT-40-REV-02
OUTDOOR DECORATIVE GAS APPLIANCE
INSTALLATION AND OPERATION MANUAL
Report No. 216-O-40-6.5
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
DANGER
IF YOU SMELL GAS:
Shut off gas to the appliance.
Extinguish any open flame.
If odor continues, keep away from the appliance and immediately call your gas supplier or fire de-
partment.
CARBON MONOXIDE HAZARD
This appliance can produce carbon monoxide which has no odor.
Using it in an enclosed space can kill you.
Never use this appliance in an enclosed space such as a camper, tent, car, or
home.
WARNING:
Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other
appliance.
An LP-cylinder not connected for use shall not be stored in the vicinity of this or any other appliance.
WARNING:
Improper installation, adjustment, alteration, service or maintenance can cause injury or property
damage. Read the installation, operating, and maintenance instructions thoroughly before installing
or servicing this equipment.
DANGER
HUSSONG MANUFACTURING CO., INC.
P.O. BOX 577
204 INDUSTRIAL PARK DR.
LAKEFIELD, MN. 56150
fire-parts.com

1
TABLE OF CONTENTS
CONTENTS
Table of Contents 1
SAFETY INFORMATION
Safety Information 2
GENERAL INFORMATION
General Information 3
ADDITIONAL COMPONENTS REQUIRED
Additional Components Required 3
OPTIONAL ACCESSORIES
Optional Accessories 3
Installation Overview 3
DIMENSIONS
Dimensions 4
SPECIFICATIONS
Determining Outdoor Location 5
Clearances to Combustibles 5
ASSEMBLY
Assembly 6-16
Propane Cylinder 15
FUEL GAS CONVERSION
Fuel Gas Conversion 17
LIGHTING AND SHUTDOWN
Lighting and Shutdown 18
MAINTENANCE
Flame Appearance 19
Cleaning 19
Inspecting 19
OPTIONAL GLASS WIND GUARD
Optional Glass Wind Guard 20
OPTIONAL COLOR CHANGING LED LIGHT KIT
Optional Color Changing LED Light Kit 21-22
REPLACEMENT PARTS LIST
Replacement Part List 23
WARRANTY
Warranty 24
fire-parts.com

2
SAFETY INFORMATION
THIS APPLIANCE IS HOT WHEN OPERATING AND CAN CAUSE SEVERE BURNS IF CONTACTED.
Do not operate appliance before reading and understanding operating instructions. Failure to operate appliance according to
operating instructions could cause fire or injury.
Installation and repair should be done only by a qualified service person. The appliance should be inspected before use and at
least annually by a qualified service person. More frequent cleaning may be required as necessary. It is imperative the control
compartment, burners and circulating air passageways of the appliance are kept clean.
Provide adequate clearance for servicing and operation.
This appliance shall be used ONLY outdoors in a well-ventilated space and shall NOT be used inside a building, garage, or any
other enclosed area.
This appliance must be installed in such a manner that proper air ventilation is maintained without obstruction at all times,
and during all weather conditions.
Improper installation, adjustment, alteration, service, or maintenance can cause injury or property damage.
Read the installation, operating and maintenance instructions thoroughly before installing or servicing this equipment.
Do not sit or place any part of the body or combustible materials on the appliance.
Children and adults should be alerted to the hazards of high surface temperatures and should stay away to avoid burns or
clothing ignition.
Y o u n g c h i l d r e n s h o u l d b e c a r e f u l l y s u p e r v i s e d w h e n t h e y a r e i n t h e a r e a o f t h e a p p l i a n c e .
Clothing or other flammable materials should not be hung from the appliance, or placed on or near the appliance.
Risk of burns. The appliance should be turned off and cooled before servicing.
Do not leave unattended when in use.
Solid fuels shall not be burned in this appliance.
Do not operate appliance in the rain.
Do not locate appliance where it can get excessively wet.
Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the
appliance and to replace any part of the control system and any gas control, which has been under water.
To extend the life of your appliance, protect and cover it from the elements when not in use.
Storage of this appliance indoors is permissible only if it has been disconnected from its fuel supply.
Always keep the appliance area clear and free from combustible materials, gasoline, and other flammable vapors and liquids.
Any guard or other protective device removed for servicing the appliance shall be replaced prior to operating this appliance.
The burner must be replaced prior to the appliance being put into operation if it is evident the burner is damaged.
Replacement burner #PF40-035 as supplied by Hussong Mfg. must be used.
Properly locate gas hose out of pathways where people may trip or where gas hose may be subject to damage.
Inspect hose before each use of appliance.
The hose assembly must be replaced prior to the appliance being put into operation if there is evidence of excessive abrasion or
wear, or if the hose is damaged. Replacement hose assembly # 600-206 as supplied by Hussong Mfg. must be used.
Do not install damaged, incomplete or substitute components.
fire-parts.com

3
This fireplace has been tested by OMNI-Test Laboratories, Portland, Oregon and complies with:
ANSI Z21.97-2012 • CSA 2.41-2012, “Standard for Outdoor Decorative Gas Appliances.”
CAN/CGA 2.17-M91 (R2009), “Gas-Fired Appliance for Use at High Altitudes.”
LP GAS NATURAL GAS
MAXIMUM INLET GAS PRESSURE 11” WC (2.74 kPa) 7” WC (1.74 kPa)
BURNER ORIFICE SIZE #50 #41
BTU/HR 40,000 BTU/hr (11.72 kW/hr) 40,000 BTU/hr (11.72 kW/hr)
CODE AND SUPPLY REQUIREMENTS: When an appliance is for connection to a fixed piping system, the installation must conform
with local codes, or in the absence of local codes with the National Fuel Gas Code, ANSI Z223.1/NFPA 54; International Fuel Gas Code,
Natural Gas and Propane Installation Code, CSA B149.1; or Propane Storage and Handling Code, B149.2, as applicable.
The appliance, when installed, must be electrically grounded in accordance with local codes, or in the absence of local codes with the
National Electrical Code, ANS/NFPA 70; or the Canadian Electrical Code, CSA C22.1, if applicable.
For appliances for use with a fixed fuel piping system and equipped with an appliance gas pressure regulator, the appliance a nd its
individual shutoff valve must be disconnected from gas supply piping system during any pressure testing of that system at pressures in
excess of ½ psi (3.5 kPa).
The appliance must be isolated from the gas supply piping system by closing its individual manual shut-off valve during any pressure
testing of the gas line at test pressures equal to or less than ½ psi (3.5 kPa).
NOTE If installing optional Color Changing LED Light Kit, do so in conjunction with assembling this appliance. If installing at a later
date, some disassembly will be required.
ADDITIONAL COMPONENTS REQUIRED
Media Tray Cover
Wind Guard Kit (2 styles available. See dealer for details).
Color Changing LED Light Kit
OPTIONAL ACCESSORIES
20 lb. (9.1 kg) propane cylind er con struct ed and marked in acco rd ance wit h the U.S. D. O.T. Specificatio ns
for LP-Gas Cylinders, or the Standard for Cylinders, Spheres and Tubes for Transportation of Dangerous Goods and Commission, CAN/CSA B399.
Tile Kit. Purchased Separately.
STATE OF MASSACHUSETTS:
Installation and repair must be done by a plumber or gas fitter licensed in the Commonwealth of Massachusetts.
Flexible connectors shall not exceed 36 inches in length.
The appliances individual manual shut-off must be a T-handle type valve.
GENERAL INFORMATION
NOTE
Porcelain tile is recommended for all outdoor applications.
Tile Trim Kit (included) is designed to accommodate 1/4” (6mm) thick porcelain tile.
WARNING This appliance is manufactured for use with LP Gas. If converting to Natural Gas, contact a licensed plumber or gas fitter to
perform the necessary tasks required to connect appliance to Natural Gas supply and convert appliance to Natural Gas.
fire-parts.com

4
488" [1221mm]
361
4" [920mm]
36" [914mm] 24" [610mm]
115
8" [296mm]
127
8" [328mm]
243
4" [629mm]115
8" [296mm]
36" [914mm] 24" [610mm]
36" [914mm] 24" [610mm]
23" [584mm]
30" [762mm]
42" [1067mm]
DIMENSIONS
23” (584mm) BASE KIT (P40-23B)
Figure 4a
TABLE TOP
30” (762mm) BASE KIT (P40-30B)
42” (1067mm) BASE KIT (P40-42B)
488" [1221mm]
361
4" [920mm]
36" [914mm] 24" [610mm]
115
8" [296mm]
127
8" [328mm]
243
4" [629mm]115
8" [296mm]
36" [914mm] 24" [610mm]
36" [914mm] 24" [610mm]
23" [584mm]
30" [762mm]
42" [1067mm]
488" [1221mm]
361
4" [920mm]
36" [914mm] 24" [610mm]
115
8" [296mm]
127
8" [328mm]
243
4" [629mm]115
8" [296mm]
36" [914mm] 24" [610mm]
36" [914mm] 24" [610mm]
23" [584mm]
30" [762mm]
42" [1067mm]
488" [1221mm]
361
4" [920mm]
36" [914mm] 24" [610mm]
115
8" [296mm]
127
8" [328mm]
243
4" [629mm]115
8" [296mm]
36" [914mm] 24" [610mm]
36" [914mm] 24" [610mm]
23" [584mm]
30" [762mm]
42" [1067mm]
Figure 4b
Figure 4c
Figure 4d
fire-parts.com

5
B
C
D
A
SPECIFICATIONS
DETERMINING OUTDOOR LOCATION
CLEARANCES TO COMBUSTIBLES
A Ground or other surface 0” (0mm)
B Side Wall 11-5/8” (296mm)
C Back Wall 11-5/8” (296mm)
D Unit top to ceiling 44” (1118mm)
1. When selecting a location, ensure all clearances are met as specified below. Other clearances may apply.
2. This appliance must be installed in an open-air situation with natural ventilation, without stagnant areas, where gas leakage and
products of combustion are rapidly dispersed by wind and natural convection.
3. Typically an outdoor space is not enclosed but, any enclosure in which the appliance is used shall comply with one of the following:
An enclosure with walls on all sides, but at least one permanent opening at ground level and no overhead cover. (Figure 5a).
Within a partial enclosure that includes an overhead cover and no more than two walls. (Figure 5b).
Within a partial enclosure that includes an overhead cover and more than two walls, the following shall apply:
a) At least 25% of the total wall area is completely open, and
b) At least 30% of the remaining wall area is open and unrestricted. (Figure 5c).
Figure 5d
Figure 5c
Figure 5b
Figure 5a
NOTE
Provide adequate clearances on left side of
appliance (access panel door) for proper
operation and maintenance purposes.
Left Front
fire-parts.com

6
ASSEMBLY
HARDWARE
Qty. Description
62 Screws
16 1/4-20 flange nuts
TOOLS REQUIRED
7/16 nut driver
1/4 nut driver
Figure 6a
M
L K
J
I H
G
G
F
D
F
E
D C
B
A
MAIN ASSEMBLY PARTS LIST
Code Description
A Burner / Valve Train Assembly
B Tile Kit (purchased separately)
C Tile Alignment Brackets
D Tile Tray Trim Kit
E Tile Tray
F Tile Tray Brackets
G Legs
H Back Side Panel
I Left Side Panel /Cylinder Access Door
J Right Side Panel
K Front Side Panel
L Floor Plate
M Universal Valve Key
N LP Cylinder Pedestal
O Glass Media (not shown)
P Leveling Bolts
Q Cross Brace ( for 30” and 42” base kit only)
N
P
Q
fire-parts.com

7
ASSEMBLY
STEP 1.
Figure 7a
X 4
Secure tile tray sections together with (4) screws.
Figure 7b
Position tile tray brackets over mounting studs.
Do not secure at this time.
STEP 2.
fire-parts.com

8
ASSEMBLY
X 16
STEP 3.
Figure 8a
Position legs over mounting studs / tile tray brackets as
shown. Secure tile tray brackets and legs with flange
nuts (4 ea. leg/ tile bracket).
STEP 4.
Figure 8b
7 screw holes
X 6 for 23” Base
X 8 for 30” Base
X 10 for 42” Base
2 screw holes
Locate back panel (without valve key assembly hole).
Secure to back legs using (6) screws, making sure
flange end with (2) holes is positioned next to tile tray
as shown.
fire-parts.com

9
ASSEMBLY
STEP 5.
Figure 9a
Locate left panel. Secure to legs using (6) screws,
making sure flange end with no holes is positioned
next to tile tray as shown.
3 screw holes
STEP 6.
Figure 9b
7 screw holes
Locate front panel (with valve key assembly hole).
Secure to front legs using (6) screws, making sure
flange with (2) holes is positioned next to tile tray as
shown.
X 6 for 23” Base
X 8 for 30” Base
X 10 for 42” Base
X 6 for 23” Base
X 8 for 30” Base
X 10 for 42” Base
fire-parts.com

10
ASSEMBLY
STEP 7.
Figure 10a
Install cylinder pedestal as shown with retention bolt
facing out. Secure with (4) screws.
Install leveling bolts into leg base mounting holes.
X 4
STEP 8.
Figure 10b
X 4
Enlist the help of another person to carefully pick the assembly up and turn it over to it’s upright position.
The 30” and 42” Base kits are equipped with a cross brace.
Using (4) screws, attach cross brace to upper leg sections as shown.
Retention Bolt
fire-parts.com

11
ASSEMBLY
STEP 9.
Figure 11a
X 4
Using (4) screws, secure tile tray to front and back
panels.
STEP 10.
Figure 11b
X 14
Install tile alignment brackets as shown, making sure
flanges face away from center. Secure with screws.
fire-parts.com

12
ASSEMBLY
STEP 11.
Figure 12a
With valve train facing front of table (side with valve
key assembly hole), install burner/valve train
assembly, setting assembly over previously installed
tile alignment brackets.
STEP 12.
Figure 12b
X 2
Secure valve bracket to tile tray with (2) screws.
NOTE If installing Optional Color Changing LED Light Kit, do so now. Follow instructions on pages 21-22.
fire-parts.com

13
ASSEMBLY
STEP 13.
Figure 13a
Thread floor plate through valve key assembly hole
an d i n to v a lv e . Tigh t e n, ma ki ng su re wh e n
completed that writing on floor plate is aligned as
shown.
STEP 14.
Figure 13b
Install tile kit. (Purchased separately).
NOTE
Porcelain tile is recommended for all outside applications.
Tile Trim Kit is designed to accommodate 1/4” (6mm) thick porcelain tile. 12” (305mm) x 12” (305mm) tile shown.
Tile kit is intended to slide underneath the burner assembly for proper fitment.
fire-parts.com

14
3
2
1
Corner Key
ASSEMBLY
STEP 16.
Figure 14b
With screws facing downward, slide corner keys (4) into rectangular grooves on both ends of short trim sections. Position one short trim
section around tile edge. Align long trim section ends with corner keys in short trim section and push mitered corners together. Install
remaining short trim section, inserting corner keys into long trim sections. Align all mitered corners, tighten set screws.
STEP 15.
Figure 14a
WARNING
D O N O T O P E R A T E T H I S A P P L I A N C E W I T H O U T G L A S S B U R N E R M E D I A I N P L A C E .
Use ONLY #PF40-G4PC-GR Glass Media in this appliance.
DO NOT substitute materials or use more than specified.
Glass media must be NO MORE than one layer deep across entire burner/screen area to avoid possible delayed ignition
and/or sooting issues.
Evenly spread glass media across burner media tray.
4
fire-parts.com

15
PROPANE CYLINDER
WARNING If these instructions are not followed exactly, a fire causing death or serious injury may occur.
PROPANE CYLINDER SPECIFICATIONS
This appliance is designed for use with a 20 lb. (9.1 kg) size propane cylinder only (not supplied).
Inspect the fu el supply co nnection fo r sign s of leak a ge (includ i n g the hose) before each use o f the app liance.
Use only LP regulator and gas hose connector included with appliance. If it evident there is excessive abrasion or wear, or if the hose is
damaged, it must be replaced prior to the appliance being put into operation. Replacement regulators and hoses must be Hussong Mfg.
approved. Contact your local dealer for details.
Propane supply cylinder must be constructed and marked in accordance with the U.S. Department of Transportation (DOT) Specifications for LP-gas
Cylinders, or the Standard for Cylinders, Spheres and Tubes for Transportation of Dangerous Goods and Commission, CAN/CSA B339.
Propane cylinder must be provided with a listed overfilling device; and
Provided with a cylinder connection device compatible with the connection for the appliance.
The LP gas cylinder used must include a collar to protect the cylinder valve.
Cylinder must be compatible with the retention means as shown in illustration.
If the appliance is not in use, the gas must be turned off at the supply cylinder.
The cylinder must be disconnected when the appliance is not in use.
Cylinders must be stored outdoors in a well-ventilated area out of reach of children.
Disconnected cylinders must have threaded valve plugs tightly installed and must not be stored in a building, garage or any other enclosed
area.
STEP 17. PROPANE CYLINDER INSTALL
1. Remove access panel from appliance, if previously installed. Page 16.
2. Loosen cylinder retaining bolt and install cylinder into tray. Tighten retaining bolt to secure cylinder.
3. Attach black hose (with regulator) to cylinder valve. Tighten.
4. Open cylinder valve (counter-clockwise) to full open position.
5. Using a soapy water solution, check for leaks at all connections before attempting to light the appliance. If soap bubbles, this would
indicate a leak. (NEVER use an open flame for testing). If a leak is found, tighten connector until no leaks are detected.
6. Reinstall appliance access panel.
WARNING Before installation, ensure propane cylinder is turned OFF.
Follow all instructions and safety warnings supplied with cylinder.
Cylinder valve
Connector
Regulator valve
Cylinder retaining bolt
Cylinder tray
Figure 15a
fire-parts.com

16
ASSEMBLY
STEP 18.
Figure 16a
Install access panel by aligning hooks on panel with slots at bottom of left side leg sections. Lift up slightly to insert access panel upper
hooks into slots at top of leg sections.
Remove by lifting up and out.
fire-parts.com

17
Figure 17a
FUEL GAS CONVERSION
This appliance is factory equipped for use with LP (propane) gas. Converting to Natural Gas requires Natural Gas Burner Orifice #41 (purchased separately).
This appliance must be connected to a 7 inch WC (1.74 kPa) gas pressure regulator if using Natural Gas.
WARNING
TH E CON VE RSION SH AL L BE CAR RIE D OUT B Y A LICE NSCED PLUMBE R O R G AS F IT TE R, IN
ACCORDANCE WITH THE REQUIREMENTS OF THE MANUFACTURER, PROVENCIAL OR TERRITORIAL
AUTHORITIES HAVING JURISDICTION AND IN ACCORDANCE WITH THE REQUIREMENTS OF THE
CAN/CGA-B149.1 OR CAN-CGA-B149.2 INSTALLATION CODES.
CAUTION
WARNING
THE GAS SUPPLY SHALL BE SHUT OFF PRIOR TO DISCONNECTING THE ELECTRICAL POWER, BEFORE PROCEEDING WITH
THE CONVERSION.
SHUT OFF GAS SUPPLY AND ELECTRIC POWER TO APPLIANCE.
SHUT OFF GAS SUPPLY BEFORE DISCONNECTING ELECTRIC POWER.
IMPORTANT For high altitude installations: Above 2000ft. (610m) US / 4500ft. (1372m) Canada, consult the local gas distributor or
authority having jurisdiction for proper de-rating methods.
1. Remove center tile (if installed) from right side of tile tray.
2. Remove (2) screws from right side of burner media tray. Carefully pull flex line / burner orifice out of burner venturi. Remove existing
orifice and replace with #41 Natural Gas Orifice.
3. Ad ju s t b u r ne r t u b e v e nt u r i t o c or re c t s et t in g b y l oo se n in g s cr e w, a d ju s ti n g c ap an d r et i g ht e ni n g sc re w.
CORRECT SETTING: NAT.: 1/8” (3mm) open / LP: 5/8” (16mm) open
4. Reinsert flex line/ burner orifice into burner venturi and secure with screws previously removed.
5. Light appliance. Check for leaks at all connections with soapy water, whether field or factory made.
6. Pressure tap is located at front of appliance, under second tile from right
end. Remove tile to access.
7. Using flathead screwdriver, turn pressure tap counter-clockwise to open.
Check pressure readings. See below. Turn clockwise to tighten.
8. Reinstall tiles.
CODE AND SUPPLY REQUIREMENTS: When an appliance is for connection to a fixed piping system, the installation must conform
with local codes, or in the absence of local codes with the National Fuel Gas Code, ANSI Z223.1/NFPA 54; International Fuel Gas Code,
Natural Gas and Propane Installation Code, CSA B149.1; or Propane Storage and Handling Code, B149.2, as applicable.
The appliance, when installed, must be electrically grounded in accordance with local codes, or in the absence of local codes with the
National Electrical Code, ANS/NFPA 70; or the Canadian Electrical Code, CSA C22.1, if applicable.
For appliances for use with a fixed fuel piping system and equipped with an appliance gas pressure regulator, the appliance and its
individual shutoff valve must be disconnected from gas supply piping system during any pressure testing of that system at pressures in
excess of ½ psi (3.5 kPa).
The appliance must be isolated from the gas supply piping system by closing its individual manual shut-off valve during any pressure
testing of the gas line at test pressures equal to or less than ½ psi (3.5 kPa).
Figure 17b
LP GAS NATURAL GAS
MAXIMUM INLET GAS PRESSURE 11” WC (2.74 kPa) 7” WC (1.74 kPa)
BURNER ORIFICE SIZE #50 #41
BTU/HR 40,000 BTU/hr (11.72 kW/hr) 40,000 BTU/hr (11.72 kW/hr)
Flex line/burner orifice Burner venturi
fire-parts.com

18
LIGHTING AND SHUTDOWN
WARNING IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR EXPLOSION MAY RESULT, CAUSING
PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.
FOR YOUR SAFETY - READ BEFORE LIGHTING
A. This appliance is lit by a match or hand fire starter.
BEFORE LIGHTING, smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than
air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS:
Shut off gas to the appliance.
Extinguish any open flame.
If odor continues, keep away from the appliance and immediately call your gas supplier or fire department.
B. Use only your hand to turn the universal key. Never use tools. If the key will not turn by hand, do not try to repair it, call a qualified
service technician. Forced or attempted repair may result in a fire or explosion, and loss of warranty.
C. Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and
to replace any part of the control system and any gas control which has been under water.
LIGHTING INSTRUCTIONS
STOP - READ SAFETY INFORMATION ABOVE.
1. Insert universal key into floor plate located at the front of appliance. Turn key clockwise to turn gas to OFF.
2. Wait 5 minutes for gas to clear out.
3. Turn ON the main gas supply. If you smell gas, STOP! Turn off gas and recheck gas connections for leaks. Do not continue until gas
leaks are corrected. If you do not smell gas, continue with next step.
4. Place a burning match to burner media surface covering the burner tube. DO NOT HOLD THE MATCH BY HAND.
5. After the match is burning and in position, turn universal key counter-clockwise to ON. Appliance should light within 5 seconds.
SHUTDOWN INSTRUCTIONS
SHUTTING OFF APPLIANCE
Turn universal key clockwise to the OFF position.
CAUTION
DO NOT turn the universal key to the ON position FOR 5 MINUTES after shutting the appliance off.
DO NOT leave universal key in floor plate when appliance is not in use.
UNIVERSAL KEY
FLOOR PLATE
Figure 18a
fire-parts.com

19
MAINTENANCE
FLAME APPEARANCE:
Flame appearance is affected by several factors including altitude and fuel quality.
Although the venturi setting has been factory set, adjustments may be necessary for optimal
performance and visual aesthetics.
When appliance is first lit, the flames will be blue. Flames will gradually turn
yellowish-orange during first 15 minutes of operation. If flames remain blue, or become
dark orange with evidence of sooting (black tips), the burner tube venturi may need
adjustment. Referring to illustration at right, periodically make a visual check of burner
flames.
Ideal flame appearance/height
Figure 19a
WARNING Do not perform maintenance tasks until the appliance has been turned off and has ample time to cool.
The appliance should be inspected before use and at least annually by a qualified service person. It is imperative the contr ol
compartment, burners and circulating air passageways of the appliance are kept clean.
Annually inspect burner tube for cracks, insect nests, excessive corrosion or other damage. Burner must be replaced prior to the
appliance being put into operation if it is evident that the burner is damaged. Replacement part #PF40-035 Burner Tube, as supplied by
Hussong Mfg. must be used. DO NOT SUBSTITUTE MATERIALS.
The hose assembly (see illustration on page 23 (R) must be replaced prior to the appliance being put into operation if there is evidence
of excessive abrasion or wear, or if the hose is damaged. Replacement hose assembly #600-206 as supplied by Hussong Mfg. must be
used. Hose assembly located behind access panel. Page 23 (I) . Lift handle up and out to remove access panel.
Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and
to replace any part of the control system and any gas control which has been under water.
INSPECTING:
Clean all leaves and debris that may have gathered on and/or around the appliance before each operation.
Turn off gas and disconnect from electrical supply before cleaning.
Keep burner and control compartment clean by brushing and vacuuming at least once a year. More frequent cleaning may be required
as necessary.
Clean appliance with damp cloth. Do not use abrasive cleaners.
CLEANING:
fire-parts.com