Kraus Allyn KPF-2654 User manual

AllynTM Single Handle Pull
Down Kitchen Faucet
KPF-2654
R
INSTALLATION MANUAL
www.kraususa.com I Toll Free: 1.800.775.0703 I © 2021 Kraus USA Plumbing LLC I REV. December 7, 2021

2
Congratulations on the purchase of your new
Kraus plumbing fixture!
Please keep the box and packaging materials until your product is
completely installed. If you have any questions, require technical
assistance or have any problems with your product:
Please contact our Customer Service Team
1-800-775-0703 / [email protected]
Have the model number available and retain a copy of your
receipt with purchase date for reference.
If for any reason this product does not meet your expectations,
please be sure to repack this product in the original box and
packaging material to avoid damage during transit.
DO NOT RETURN TO STORE
STOP
R

3
Prior to Installation:
·Make sure you have all necessary parts by checking the diagram and
parts list. If any part is missing or damaged, please contact Kraus
Customer Service at 800-775-0703 for a replacement.
·Read all instructions and safety warnings and ensure you have all tools,
parts, and equipment necessary for a safe installation.
·Turn off the hot and cold water supply at the angle stops and turn on
the old faucet to release any built up pressure. Remove existing faucet.
Clean sink or countertop to remove any debris, plumber’s putty, or
silicone.
·Flush angle stops to release any debris prior to installation.
·Pre-drilled hole size requirement: 1 3/8" (min)
·Max countertop thickness: 2 1/4”
Care & Maintenance
* To keep the product clean & shining, follow the steps below:
1. Rinse with clean water & dry with a soft cloth
2. Do not clean with soaps, acid, polish, abrasives or harsh cleaners
3. Do not use cloth with a coarse surface
4. Unscrew the aerator and clean when necessary
* This installation manual is subject to change without further notice.
For technical assistance or replacement parts, please contact Kraus
Customer Service and one of our representatives will be happy to help:
Toll-Free: 800-775-0703 or [email protected]
ACID
R
STOP

4
Tools Required
4
Adjustable Wrench Phillips Screwdriver Silicone Sealant
Safety Goggles Pipe Tape

55
Diagram and Parts List
1. Spray Head
2. Faucet Body
3. O-Ring
4. Waterlines
5. Quick Connector
6A. Metal Washer
6B. Mounting Nut
6C. Mounting Screws
7. Hex Wrench
8. Weight
9. Spray Hose
1
2
4
5
6A
6B
6C
7
8
9
3

66
Faucet Dimensions
Installer Tip:
Shut off main water supply before installing new faucet.
3 3/4"
(95mm)
9 5/8"
(245mm)
4"
(101mm)
5°
8 3/4"
(222mm)
17 3/8"
(441mm)
7 1/2"
(190mm)
3/8" Connection
Max.
2 1/4"
(57mm)
Ø1 3/8"
(35mm)
11 1/4"
(285mm)

7
Step 1. Installing the O-Ring
Step 2. Install faucet and mounting hardware
Install the O-Ring (3).
Insert faucet body (2) into the hole
in the sink or countertop. Install
mounting hardware (6A, B & C)
from underneath the countertop.
3
6A
6B
6C

8
Step 3. Secure mounting hardware
Adjust direction of faucet body (2)
so that handle is on right side of
faucet. Tighten mounting nut (6B)
until snug. Tighten mounting
screws (6C) to nut with Phillips
screwdriver until snug.
Step 4. Attach spray hose and counterweight
Connect the spray hose (9) to
quick connector outlet (5)
attached to the supply line. Install
the weight (8) on the spray hose
where it is marked.
8
5
2
6C
6B

9
Step 5. Connect waterlines
Connect hot and cold copper lines
(4) to angle stops. Tighten both
ends of waterlines with a wrench
until snug. Turn on hot and
cold angle stops and check
for leaks.
Step 6. Flush spray hose
Remove spray head (1) from
spray hose. Hold tip of spray hose.
Turn faucet on and let the water
run for 60 seconds to flush any
debris.
4
NOTE: Please make sure filter
washers are installed before
connecting to the main valve.

10
Step 7. Check for leaks
Check for leaks at the
connections. Retighten if
necessary.