Kraus Oletto KPF-2631CH User manual

Single Handle Kitchen Faucet
KPF-2631
INSTALLATION GUIDE
www.kraususa.com I Toll Free: 1.800.775.0703 I © 2019 Kraus USA Inc. I REV. MAR 26, 2021
Oletto™

Congratulations on the purchase of your new
Please keep the box and packaging materials until your product is
completely installed. If you have any questions, require technical
assistance, or have any problems with your product:
Please contact our Customer Service Team
1-800-775-0703 / [e-mail]
Have the model number available, and retain a copy of your receipt
with purchase date for reference.
If for any reason this product does not meet your expectations,
please be sure to repack this product in the original box and
packaging material to avoid damage during transit.
DO NOT RETURN TO STORE
1

Prior to Installation:
•Make sure you have all necessary parts by checking the diagram and parts list. If
any part is missing or damaged, please contact Kraus Customer Service at 800-775-
0703 for a replacement
•
•Pre-drilled countertop hole size requirement: 1-3/8”(min)
•Max countertop thickness: 2-1/8”
Tools you will need:
13
Wrench Phillips Screwdriver Safety Goggles
Silicone Sealant
(optional)
Pipe Tape
2
Turn o the hot and cold water lines at the angle stops and turn on the old faucet
to release any built-up pressure

3
A. Sprayer
C. Escutcheon
D. Gasket
Diagram and Parts List
F. Weight
G. Weight Clip
B. Faucet Body
E. Easy Install Assembly
H. Quick Connector
I. 2.5mm Hex Wrench
J. 6mm Hex Wrench
B
C
D
E
I
G
F
A
J
H

4
Faucet Dimension
Installer Tip:
10 1/4"
[259mm]
21 7/8"
[555mm]
2 1/8"
[54.1mm]
11"
[279.6mm]
9 1/8"
[233.2mm]
8 1/2"
[215.4mm]
2 1/2"
[62mm]
10 3/4"
[274.6mm]
8 1/4"
[209.5mm]
2"
[52mm]
21 5/8"
[549mm]
3/8”-compression

5
Step 1a: Installing the easy install assembly (Without escutcheon)
Shut o the water supply. Remove the old
faucet. Clean the mounting surface. Check
for the proper thickness of the sink.
Insert the base (a) into sink. If your model
does have a escutcheon, skip to step 1 b.
Step 1b: Installing the easy install assembly (With escutcheon)
Place the escutcheon (C) and the gasket (D)
on the sink. Insert the base (a) into
escutcheon (C). Note: “Front” on the base (a)
must face the front of the sink. The two
mounting plates (b) on the base (a) must be
loose and movable during the installation of
the base (a). If the sink is uneven, use silicone
under the gasket (D).
a
b
a
C
D
C
b
NOTE: “Front” on the base (a) must face the
front of the sink. The two mounting plates (b)
on the base (a) must be loose and movable
during the installation of the base (a).

Step 2: Installing the easy install assembly
6
Fig 1 Fig 2
Press the base (a) and escutcheon (C) so that they can not move, then turn the
screws with the provided hex wrench (J, HEX: 6.0mm) clockwise, as shown Fig 1.
When the mounting plates (b) make contact with the sink (1), continue to turn
the screw with the provided hex wrench (J, HEX: 6.0mm) clockwise, as shown
Fig 2, until the base (a) is completely tightened and secured, as shown Fig.4.
Fig 3
Fig 4
C
J
a
b1
C
J
a
b
1
C
J
a
b
1
C
J
a
b
1

Step 3: Installing the faucet
7
Insert the hose (1)、supply lines (2) and quick connect hose (3) one by one
through the hole of the base (a). Carefully insert the hoses into the base.
Place the faucet assembly onto the base (a) as shown in the above gure.
Secure the faucet assembly (B) by tightening the set screw with the provided
hex wrench (I, Hex: 2.5 mm).
2
1
3
a
I
B

8
Step 4: Securingthe faucet assembly
Installthe weight clip (G) at the point of
the hose marking "weight here". Insert
the weight (F) onto the weightclip (G)
by sliding it down onto the weight clip (G).
Step 5: Connect waterlines to main valve
Attach waterlines to angle stops
and tighten until snug. Turn on angles
stops and check for leaks (DO NOT TURN
FAUCET ON)
Weight
here
Weight
here
G
F
NOTE
are installed before connecting to
the main valve

9
Step 6: Flush faucet
Pull the hose assembly out of the spout and
remove the sprayer (A) by unscrewing it
from the hose in a counterclockwise direction.
Be sure to hold the end of the hose down into
the sink and turn the faucet on to the warm
position where it mixes hot and cold water.
Flush the water lines for one minute. This
ushes away any debris that could cause
damage to internal parts. Check for leaks.
Re-tighten any connections if necessary, but
do not overtighten. Reinstall the sprayer (A)
by hand tightening it back onto the sprayer
hose.
After installation is completed, turn on the
hot and cold water supplies. Check for leaks.
NOTE: Please make sure washer is
installed attaching sprayer to hose.
A