Kraus Artec Pro KPF-1603 User manual

Artec Pro™Single Handle Commercial
Kitchen Faucet
KPF-1603
INSTALLATION GUIDE
www.kraususa.com I Toll Free: 1.800.775.0703 I © 2018 Kraus USA Inc. IREV. Aug 21, 2018

1
Congratulations on the purchase of your new
Please keep the box and packaging materials until your product is
completely installed. If you have any questions, require technical
assistance, or have any problems with your product:
Please contact our Customer Service Team
1-800-775-0703 / [e-mail]
Have the model number available, and retain a copy of your receipt
with purchase date for reference.
If for any reason this product does not meet your expectations,
please be sure to repack this product in the original box and
packaging material to avoid damage during transit.
DO NOT RETURN TO STORE
1

2
Prior to Installation:
• Make sure you have all necessary parts by checking the diagram and parts list. If
any part is missing or damaged, please contact Kraus Customer Service at 800-775-
0703 for a replacement
•
to release any built-up pressure
• Pre-drilled countertop hole size requirement: 1-3/8” (min)
• Max countertop thickness: 2”
Tools you will need:
13
Wrench Phillips Screwdriver Safety Goggles
Silicone Sealant
(optional)
Pipe Tape

3
Diagram and Parts List
B4
B5
C
A
A. Faucet Body
B1. Seat
B2. Rubber Washer
B3. Metal Washer
B4. Mounting Nut
B5. Screw
C. 2.2 GPM Flow Restrictor
D. Hex Wrench
B1
B2
B3
D

4
Faucet Dimension
Installer Tip:
4 1/8in
[106.5mm]
24 3/4in
[628.7mm]
2 3/8in
[60.0mm]
9/16-24UNEF-2B
7 1/8in
[182.6mm]
9 3/4in
[248.2mm]
6in
[153.2mm]
7 5/8in
[198.2mm]
6 5/8in
[173.3mm]
MAX:2 3/8in
[60.8mm]

5
Step 1: Remove washer and lock nut
Insert faucet through hole in sink or
countertop.From underneath sink,
attach the seat (B1), rubber washer (B2),
metal washer (B3), and nut (B4). Lock
nut (B4) into position by tightening
screws (B5).
Shut o the water supply.
Remove the old faucet. Clean the
mounting surface. Remove mounting
hardware (B) from faucet body (A).
Step 2: Install faucet
B1
B2
B3
B4 B5
A
B

Step 3: Making the water supply connections
Push the quick connector (2) rmly
upward andattach it to the receiving
block (1). Pull down moderately to
ensure the connection has been made.
If it is necessary to remove the quick
connector (2), squeeze the tabs on the
hose and then pull down to disconnect.
6
Step 4: Making the water supply connections
Thread the nut (1) on the supply line
onto the outlet of the water supply
valve and tighten with a wrench.
Do not overtighten.
1
1
2

1
10
9
11
12
Step 5: Flushing and checking for leaks
Pull the hose assembly out of the spout
and remove the spray head by
unscrewing it from the hose in a
counterclockwise direction. Be sure to
hold the end of the hose down into the
sink and turn the faucet on to the warm
position where it mixes hot and cold
water.
Flush the water lines for one minute. This
ushes away any debris that could cause
damage to internal parts. Check for leaks.
Reinstall the spray head by hand
tightening it back onto the spray hose.
7
279
10 31/32”
Minimum distance 90mm
Cold Wat
Max35
217
8 17/32”
Max1 3/8”
NOTE:
1.Do not lose the rubber washer (1) when
installing back the sprayer
2.The magnet end marking with black dot
should be toward the hose for correct
magnet installation
1
2

This faucet ships with a 1.8 GPM ow
restrictor installed. An optional 2.2 GPM
ow restrictor is also included in the box.
To switch the ow rate of the faucet:
1. Disassemble the quick connect assembly
by separating the connector (1) and quick
connect (2).
2. Replace 1.8 GPM connector (blue) with
the 2.2 GPM connector.
3. Reinstall the quick connect assembly.
1
10
9
11
12
Step 7: Flow Regulator Replacement
8
279
10 31/32”
Minimum distance 90mm
Cold Wat
Max35
217
8 17/32”
Max1 3/8”
2
1
2
1
1
To activate the spray mode, simply
press the handle (1) located under
the spray head.
1
Step 6: Flush faucet
NOTE: In compliance with CEC standards, this faucet is designed with a 1.8 gpm
ow rate. At your discretion, you may modify the product with the included 2.2
gpm restrictor. Please note that doing so will remove the capability of this product
to meet specic low-ow standards. Kraus is not liable for any alterations made to
the product post-sale, and highly advises that you consult with your local or
statewide plumbing enforcement agency prior to any modication.

Replacement Parts
1. Spray head
Replacement Parts List Part NO
2. Magnet
3. Spray hose assembly
4. Spring
5. Inverter
6. Spray support assembly
7. Spout nut
8. Spout
9. Diverter
10. Aerator assembly
11. Cartridge
12. Bonnet nut
13. Cap
14. Handle assembly
15. Rubber & metal washer
16. Mounting nut & nut
17. Block
18. Flange
19. Seat
20. 2.2GPM ow restrictor
21. 1.8GPM ow restrictor
22. Quick connect
23. Hex wrench
CH, SFS, SFSMB
Finish
BLBG, BLSFS,
GRCH, GRSFS*
CH, SFS, BG
CH, SFS, BG
CH, SFS, BG, MB
CH, SFS, BG, MB
CH, SFS, BG, MB
CH, SFS, BG
CH, SFS, BG
CH, SFS, BG
Less than 90mm
32 3/32”
Ø35~Ø38
1
23
4
6
8
45
67
8
Ø1 3/8”~Ø1 1/2”
815
194
7 5/8”
Ø1 3/8~Ø1 1/2”
30˚
10
8
7
Ø35~Ø38
9
1
2
3
4
5
6
7
8
9
10 1112
13
14.2
14.3
14.1
17
21
20 23
22
18
16
15
19
KP27063
KP27080
KP27064
KP27065
KP27066
KP27067
KP27068
KP27069
KP27070
KP27071
KP27072
KP27028
KP27079
KP27073
KP27077
KP27078
KP27075
KP27074
KP27076
KP27020
KP27060
KP27061
KP27062
*Spray hose assembly color options: Black hose w/ Brushed Gold connector (BLBG), Black
hose with Spot-Free Stainless connector (BLSFS), Gray hose with Chrome connector (GRCH),
Gray hose with Spot-Free Stainless connector (GRSFS)