Kraus FUS-13901 User manual

INSTALLATION MANUAL
Aquila Single Lever Basin Faucet
FUS-13901
www.kraususa.com I toll free: 1.800.775.0703 I © 2014-2015 Kraus USA Inc.

Thank you for purchasing Kraus
We would like to take this opportunity to thank you for your business with Kraus
USA. It is our sincere hope that you are completely satised with your experience.
We welcome any questions or comments you may have, and will be glad to assist
you in the future.
For more information about Kraus products, please visit our website at:
www.kraususa.com
Please register your new Kraus product at the following web address in order to
activate the warranty and receive the full benet of customer support:
www.kraususa.com/registration
Sincerely,
Kraus Customer Service Department

Prior to Installation:
• Make sure you have all necessary parts by checking the diagram and parts list. If
any part is missing or damaged, please contact Kraus Customer Service at 800-775-
0703 for a replacement
• Turn o the hot and cold water supply at the angle stops and turn on the old
faucet to release any built up pressure. Remove existing faucet. Clean sink or
countertop to remove any debris, plumber’s putty, or silicone
• Place bucket under angle stops. Turn on to ush any debris prior to installing new
plumbing. Shut o angle stops
• Pre-drilled hole size requirement: 1-3/8” (min) – 1-1/2” (max)
• Max countertop thickness: 1-3/8”
Safety Goggles
Adjustable Wrench
6 5/8”
5 4/5”
3/8”
(10mm)
7/8”
19.7º(22mm)
8 5/16”
1 1/4-18UNF-2A
(21mm)
10 1/8”
(257mm)
1 3/8”
(35mm)
3 3/4”
(168mm)
(147.3mm)
(96mm)
∅ 1 3/4”
(
∅ 45mm)
∅ 1 15/16”
(
∅ 50mm)
9/16”-18UNEF
27mm ~ 41.3mm 1 1/16” ~ 1 5/8”
∅ 1 15/16”
(
∅ 50mm)
12 7/16”
(316mm)
1 5/8”
(42.5 mm Max)
7A
8B
8C
8D
8A
7A
8B
8C
8D
8A
Bucket
Phillips Screwdriver
Tools you will need:

FUS-13901 Diagram and Parts List
A
B
I1
I2
I3
D
C
J
E
F
G
H
A. Faucet Body
B. Base Metal Ring
C. Base O-Ring
D. Rubber O-Washer
E. Metal U-Washer
F. Mounting Screws
G. Mounting Nuts
H. Hot & Cold Waterlines
I. Aerator Assembly
I 1. Aerator Washer
I 2. Aerator
I 3. Aerator Cover
J. Hex Wrench

Faucet Dimensions

Lift Rod Drain Diagram and Parts List
a
b
c
d
e
f
g
ijkl m
n
o
p
h
a. Waste Stopper
b. Drain
c. Rubber Washer
d. Concave Washer
e. Plastic Washer
f. Mounting Nut
g. Tailpipe Washer
h. Tailpipe
i. Top Hat Washer
j. Drain Off Pole
k. Washer
l. Retaining Nut
m. Extender Rod
n. Clip
o. Thumb Screw
p. Lift Pole

Lift Rod Drain Dimensions
a
b
c
d
e
f
g
ijkl m
n
o
p
h

Step 1: Install mounting hardware and waterlines
Remove faucet, mounting
hardware, and waterlines from
the box. Remove mounting nuts
(G) from mounting screws (F).
Place faucet body (A) on a soft
cloth, spout facing up. Secure
hot & cold waterlines (H) at
the base of the faucet (HAND-
TIGHTEN ONLY)
A. Hot Side: Left
B. Cold Side: Right
Thread mounting screws (F)
into faucet base, at head up,
and tighten with a Phillips head
screwdriver until snug. Place
base O-ring (C) in groove of base
metal ring (B)
Step 2: Install faucet
Install faucet body (A) through
1-3/8” hole in countertop or sink,
with hot & cold waterlines (H),
mounting screws (F), and base
metal ring (B) attached
A
A
H
D
E
G
F
H
H
C
B
B
F
H
F
G
A
A
H
D
E
G
F
H
H
C
B
B
F
H
F
G

Step 3: Secure faucet
Install rubber O-washer (D)
and metal U-washer (E), over
waterlines (H) and mounting
screws (F), from underneath
the countertop or sink. Attach
mounting nuts (G) to mounting
screws (F) and tighten with
adjustable wrench or 10mm
wrench until snug
Step 4: Connect waterlines to main valve
Thread hot & cold waterlines (H)
onto angle stops and tighten with
adjustable wrench until snug. Turn
on angle stops and check for leaks
(DO NOT TURN ON FAUCET)
A
A
H
D
E
G
F
H
H
C
B
B
F
H
F
G
A
A
H
D
E
G
F
H
H
C
B
B
F
H
F
G

Step 5: Install Drain
a
b
c
d
e
f
g
poo
n
jkl
n
m
l
p
m
a
d
g
b
h
a
b
b
c
e
f
h
ikl
o
p
I 1
I 2
I 3
j
a
b
c
d
e
f
g
poo
n
jkl
n
m
l
p
m
a
d
g
b
h
a
b
b
c
e
f
h
ikl
o
p
I 1
I 2
I 3
j
a
b
c
d
e
f
g
poo
n
jkl
n
m
l
p
m
a
d
g
b
h
a
b
b
c
e
f
h
ikl
o
p
I 1
I 2
I 3
j
• Remove waste stopper (a) from
drain (b). Remove tail pipe (h),
mounting nut (f), plastic washer
(e), and concave washer (d) from
drain (b). Remove retaining nut
(l) and washer (k) from tailpipe
(h)
• Install drain (b), with rubber
washer (c) attached, into the drain
hole. Attach concave washer (d)
with narrow end up, plastic washer
(e), and mounting nut (f) to drain
(b) from underneath countertop or
sink. Secure tightly to sink with an
adjustable wrench
• Thread tailpipe (h) onto drain (b)
and hand-tighten. Adjust tailpipe
(h) so drain o pole opening is to
the rear of the sink
Installer tip: Leave top hat
washer (g) in tailpipe (h)
Installer Tip: Make sure
tailpipe washer (g) is installed
in tailpipe (h)