Kraus KPF-1620 User manual

Product Description and Measurements
Installation Instruction
Single Lever Pul Out Sink Mixer
MODEL-KPF-1620
Prior To Installation Steps
1. Unpack your new product and ensure that all the parts are contained in the packaging.
Keep the product in its original box until you are ready to install it.
2. Shut off the water supply if replacing a previously-installed faucet.
3. Observe all plumbing and building codes in your area.
4. It is recommended that installation of the product be done by a professional plumber.
Dear Valued Customer,
Kraus would like to take this opportunity to thank you for purchasing Kraus products. It is our sincere
hope that you are completely satisfied with your new purchase. We welcome any questions or comments
you may have and look forward to assisting you in the future.
Sincerely,
Kraus customer service department.
Installation Steps
1. Shut off all water supply prior to installation
2. Remove the metal spring (#14) by disassembling it from the hose.
3. Screw on the aerator head (#2) onto the spout (#3). Make sure that a black rubber washer is attached to the
end of the hose prior to attaching the aerator head.
4. Place the black rubber o-ring (#4) into the metal ring (#5).
5. Place the metal ring (#5) onto the faucet body (#1).
6. Unscrew the brass nut (#7) from the brass screw (#6).
7. Place the faucet on the countertop.
8. If the countertop is thin or the faucet is being mounted on the sink itself, place the countertop extender (#15)
from underneath the countertop and tighten it onto the brass screw. **Optional**
9. Place the rubber washer (#8) and then the metal washer (#9) onto the brass screw from underneath the
countertop.
10. Tighten the brass nut (#7) onto the brass screw (#6).
11. Place the plastic enclosure (#10) onto the hose and situate the smaller opening onto the brass screw (#6).
12. Place the spring (#14) onto the hose.
13. Place the red hard washer (#11) into the hose inlet (#13) and screw the hose (#12) (with the spring already
attached) onto the brass screw (#6).
14. Screw in the hot and cold waterlines (#16) and attach them to the water supply.
Contact us toll-free at kraususa.com. Copyright ©2008 - 2009, Kraus USA Inc. 1-800-775-0703; or visit our website at www.

Installation
MODEL-KPF-1620
5
4
6
8
9
7
10
11
13
14
12
16
15
Code Parts List Quantity
Faucet Body
Aerator Head
Spout
Rubber O-Ring
Metal Ring
Brass Screw
Brass Nut
Rubber Washer
Metal Washer
Plastic Enclosure
Red Hard Washer
Hose
Hose Inlet
Spring
Counter Top Extender (optional)
Hot & Cold Water Lines
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
2
3
Contact us toll-free at kraususa.com. Copyright ©2008 - 2009, Kraus USA Inc. 1-800-775-0703; or visit our website at www.

Installation
MODEL-KPF-1620
17.4’’
5.8’’
9.8’’
8.8’’
Max 1.4’’ Max 1.4’’
Pull Out Hose
Care & Maintenance
In order to maintain your faucets original finish simply rinse with warm clean water and blot dry with a clean
soft cloth only.
Avoid using corrosive detergents, polishers, scrapers or any other abrasive materials. In case a buildup of dirt
or mineral deposits should occur, gently remove it using a mild detergent or a mixture of vinegar with water to
soften the build up and clear it away. Rinse thoroughly and immediately with water to assure no detergent
remains on the surface and dry with a soft cloth.
At Kraus your satisfaction with quality and durability of our products is extremely important to us. Therefore,
we hope for you to keep our recommendation as a reminder, in order to prolong the lifespan of your faucet.
Contact us toll-free at kraususa.com. Copyright ©2008 - 2009, Kraus USA Inc. 1-800-775-0703; or visit our website at www.