
TROUBLESHOOTING GUIDE
AUTHORISED KREEPY KRAULY ACCESSORIES
Cross Bar
When prevention of Kreepy Krauly
climbing pool walls is required.
Main Drain Cover
Used to replace the main drain grille
to ensure smooth travel of Kreepy
Krauly over the main drain. Simple
installation. NO screws required.
Expanding Plug
Used for blocking some types of
skimmer box pool drain inlets.
Roller Bumper Strap
Used in pools with rough surfaces
where standard bumper strap may
wear excessively.
Vacuum Plate Clamp
Used to hold down the vacuum plate
when the pool pump is off.
Wheel Deflector
Prevents Kreepy Krauly from
becoming caught in tight corners or
between steps and the pool wall.
Kreepy Krauly pulsates
rapidly but remains
stationary, or travels very
slowly.
Kreepy Krauly travels
around water line in one
direction only.
Kreepy Krauly travels too
slow, or does not pulsate.
Low vacuum, slow,
faltering hammering
sound.
Kreepy Krauly does not
sit at an angle of 45° and
has difficulties in attaching
itself to the pool floor.
Kreepy Krauly stays at one
end of pool.
Sole not fitted
Sole tread worn away.
Combined vacuum
control MiniSkim or
AutoSkim valve not fitted.
Seal fitted upside down.
MiniSkim or optional
AutoSkim valve jammed.
Main body and swivel
head are out of line.
Filtration unit blocked.
Pump impeller blocked.
Pump or skimmer box
strainer basket full, or
blocked.
Main drain valve open.
Inlet from main drain
leaking.
Combined vacuum plate
and AutoSkim valve
leaking.
More than one skimmer
box fitted to pool.
Blockage within Kreepy
Krauly machine or hose.
Pool pump unit does not
develop enough vacuum
to power the Kreepy
Krauly machine.
Hose weight(s) is
incorrectly positioned on
hose, or is not fitted.
Bumper strap not fitted.
Float foam missing.
Kreepy Krauly hose too
short.
Kreepy Krauly hose is
kinked or coiled.
Return to pool outlets
force Kreepy Krauly hose
away from that area.
Fit new sole
Replace with new sole.
Fit as per instructions.
Refer to markings on seal
to determine correct fitting.
Remove valve from plate.
Hold under water and
operate by hand to free
sand or grit. Dry off water
and spray with good
quality Silicon Lubricant.
Replace in vacuum plate.
Adjust Kreepy Krauly
machine so main body
and swivel head are
perfectly aligned.
Clean filter thoroughly.
Clean pump impeller vanes.
Clean strainer basket.
Shut off main drain
valve, or fit expanding
plug. (Available from
your Kreepy Krauly
representative.)
Install expanding plug.
Check correct size
plate was supplied and
re-install ensuring correct
seating in skimmer box.
Block off water flow from
skimmer boxes other than
the one to which Kreepy is
fitted.
Clean out obstruction in
machine, or flush out hose.
Check for faulty pump,
or possibly fit a more
powerful unit.
Fit hose weight(s) and
adjust by moving furthest
weight closer to or further
away from the machine
until suction seal is flat on
the pool floor.
Fit bumper strap.
Replace float foam.
Fit correct length of
Kreepy Krauly hose or
use hose joiner to extend
existing hose.
Lay hose out straight in
the hot sun until kinks
disappear, and allow
to cool in that position.
Alternatively a similar
treatment using warm
water can be used, please
consult your Kreepy
Krauly representative.
Adjust outlets so they do
not influence the Kreepy
Krauly.
Kreepy Krauly travels
slowly or does not
pulsate; bubbles noticed
at return to pool outlets.
Kreepy Krauly wedges
itself on, or around step
area.
Kreepy Krauly repeatedly
comes level with the
surface of the pool,
possibly drawing in air.
Kreepy Krauly sticks to
main drain.
Kreepy Krauly will only
climb part way up the
pool wall and tends to
remain in that position.
Incorrect hose fitted to
Kreepy Krauly machine.
Air leak in the plumbing
system, check following item:
Hair and lint, pot lid or “O”
ring incorrectly fitted.
Inground pipes broken,
or leakage at joints in
system.
Hole in Kreepy Krauly
hose.
Pump has lost its prime.
MiniSkim or AutoSkim
valve jammed, clean and
replace.
Pool water level too low.
AutoSkim valve fitted too
close or above the water
level (if fitted).
MiniSkim or AutoSkim
valve not installed.
Hose weight(s) fitted
incorrectly.
Large leaves blocking
MiniSkim or AutoSkim
valve (generating excessive
vacuum).
Poor finish of pool floor
around the main drain.
Sole worn.
A genuine Kreepy Krauly
hose MUST always be
fitted to the machine. The
addition of an extra hose
weight along the hose can
assist directional stability.
Check “O” Ring for
damage, replace if
necessary and refit
correctly.
Consult your pool service
man.
Locate by lifting hose near
surface of water and listen
for hissing sound, use hose
joiner to rectify the problem.
Reprime pump.
AutoSkim valve jammed.
Clean and replace.
Fill pool to correct level.
Fit anti-vortex washer on
valve.
A special step deflector
bumper is available
from your Kreepy Krauly
representative. Alternatively
restrict movement of
Kreepy Krauly away from
the problem area by
shortening the hose if this
is practical. Any small area
missed by Kreepy Krauly
can easily be swept down
afterwards.
Fit AutoSkim valve inside
skimmer box as per
instructions.
Readjust hose weight(s).
Clean valve.
Fit a Kreepy Krauly main
drain cover over drain.
Fit a Kreepy Krauly main
drain cover over drain.
Fit new sole.
Remove baffle plate by pressing plastic clips inwards, clear flow valve and
replace baffle plate and sole.
HOW TO CLEAN THE FLOW VALVE
ATTENTION POOL BLANKET OWNERS
When a Pool Blanket is in use, carefully monitor your chlorine or salt
water chlorinator settings to avoid over chlorinating your pool which
may damage your Kreepy Krauly and void your Warranty.
The Pool Blanket prevents chlorine evaporating reducing the need
to add more chlorine. If you have a salt water chlorinator remember
to lower the amount of chlorine produced when the pool blanket is
in use. If you have any questions please call our Customer Service
department on 13 80 90 or your local pool Clark Rubber Store.
When servicing your Kreepy Krauly, look for
this seal to ensure that the part you are buying
is a certified genuine Kreepy Krauly part. REFER TO HOSE INSTALLATION SECTION
TWIN VALVE AUTOSKIM The unique
automatic “AutoSkim” Skimmer valve and
vacuum plate combination ensures full
surface skimming of all floating leaves
and debris. “AutoSkim” is available as an
optional extra with the VTX3.
AutoSkim INSTALLATION
A Kreepy Krauly AutoSkim Combination Vac/
Plate Skim Valve is recommended for superior
performance and continued maximum
surface skimming. Pools with high flow pump
and filter systems are recommended to use
a Kreepy Krauly AutoSkim combination Vac/
Plate Skim Valve.
OPTIONAL EXTRA
BALANCE SYSTEM
Kreepy Krauly works most effectively when inclined at 45° with the seal flat
on the pool surface. To test the balance adjustment switch off the pool pump,
tow Kreepy Krauly into approx. 1.2m of water and allow it to settle to bottom.
The seal must be sitting flat on the pool floor and the drive tubes should be
at 45° to the floor. If Kreepy Krauly is lifting (i.e. at an angle of more than
45°), move the second hose weight towards the swivel. Adjust until the seal
sits flat on the pool surface. Allow Kreepy Krauly to settle back to the bottom
after each adjustment to get a fair evaluation. Turn your pump on and
Kreepy Krauly will move around your pool cleaning it automatically.
Note: If you have difficulty balancing Kreepy Krauly, remove the first hose
weight or consult your local Kreepy Krauly service centre by phone for advice.
Adjusting the angle and balance of Kreepy Krauly
If Kreepy Krauly is inclined at an angle greater than
45°, move the second hose weight towards the
swivel head assembly.
45°
Installation and Operation Manual
We reserve the right to revise, change, or modify Kreepy Krauly without incurring any
obligations to make like changes on Kreepy Krauly’s previously sold. This publication
remains the sole copyright of Sherwood Overseas Co. Pty. Ltd. Written consent must be
obtained before any of its contents are reproduced.
FOR SALES AND SERVICE, PLEASE CALL 1800 777 255
OR CONTACT YOUR LOCAL STATE DISTRIBUTOR
For further information and service, visit our website
www.kreepykrauly.com.au
SHERWOOD OVERSEAS CO. PTY. LTD.
A.B.N. 13 008 756 750
KREEPY KRAULY DIVISION
321 Selby Street, Osborne Park, Perth, W.A. 6017 Australia.
Telephone: (08) 9446 9811 Facsimile: (08) 9445 3457
Email: service@kreepykrauly.com.au
PROUDLY DESIGNED
AND MADE IN AUSTRALIA
PROUDLY DESIGNED
AND MADE IN AUSTRALIA
Dive Float
Assembly
Main Body
Assembly
Swivel Head
Assembly
Hose Weight
Bumper
Strap
Pleated
Seal
Hose
Protector
Sleeve
Retaining
Collar
KleverSkim
FOREWORD This manual is a guide to introduce you to the Kreepy Krauly pool
cleaning system. It cannot cover the requirements of every installation, so please
contact your local Clark Rubber store for further advice should you need it.
INTRODUCTION
Congratulations on the purchase of your Kreepy Krauly automatic pool cleaning
system. It is designed to prevent your pool from ever getting dirty and will provide
you with many extra hours of leisure in and around your swimming pool.
The Kreepy Krauly System requires no power source, operates hydraulically and
has a 1 year warranty from the date of purchase, excluding fair wear and tear.
The only working part in the Kreepy Krauly System is the Flow Valve which is
guaranteed for 10 years. The system has 3 major components, the Cleaner
Unit, Special Hose and the Vacuum Plate with anti-surge and AutoSkim valves.
HOW IT WORKS
Water flow from the main body assembly is alternately diverted into either the
top or bottom drive tubes of Kreepy Krauly. The inertia of water trapped in each
of the drive tubes provides a lifting and propelling action.
In operation, Kreepy Krauly travels around the pool, trailing the vacuum hose and
the hose weights neutralize floatation of the vacuum hose near to Kreepy Krauly.
The combined vacuum plate control and AutoSkim valve supplied with Kreepy
Krauly regulates the amount of vacuum supplied by the filtration system, also
allowing pool surface skimming (providing the pool filtration system has an
adequate flow).
PREPARING YOUR POOL
For effective operation of Kreepy Krauly, all water flow through the main drain
must be effectively blocked off. Kreepy Krauly will vacuum clean any well
equipped pool, but it will not overcome problems associated with inadequate or
improperly maintained filtration systems.
The vacuum cleaning performance depends upon having an adequate filter
system properly cleaned and maintained. This means that your pump and filter
system should be operating efficiently. There must be good water flow into the
suction side of the pump (skimmer) and good discharge from the pool inlet.
All plumbing lines should be clear, strainer basket should be emptied and sand
filters should be backwashed. Diatomaceous earth filters should be cleaned and
recharged in accordance with their manufacturer’s instructions. Cartridge filters
should be thoroughly and carefully cleaned.
ASSEMBLING YOUR KREEPY KRAULY
Please read this manual carefully before assembly and installation of your Kreepy
Krauly. Like all pool equipment, periodic maintenance is required so please refer
to the maintenance section of this manual for normal maintenance requirements.
Kreepy Krauly is shipped to you partly assembled. Remove all the parts from the
box. Assemble your Kreepy Krauly on a clean working surface. The hose and
vacuum plate assembly are packed in separate cartons from the machine.
STEP 1 Pleated Seal STEP 2 The Sole
The pleated seal is fitted as shown
and rotate freely.
Observe the warning “this side up”.
The deflector clicks onto the white
housing above the main body with
the lugs facing down.
The sole is fitted to the foot of the
main body as shown.
Press the float arms into the white
housing until they click in place.
STEP 3 The Deflector STEP 4 Float Assembly
STEP 5 Bumper Strap
The bumper strap fits tightly into the main body as shown.
The other end is fitted into the swivel head. Ensure full insertion.
Bumper
Strap
Bumper
Strap
Sole
Seal
CARING FOR YOUR KREEPY KRAULY
Any mechanical device is subject to breakage or damage due to neglect, but
with a little care Kreepy Krauly will give you many years of excellent service. It is
recommended that Kreepy Krauly is cleaned with detergent and water periodically.
DO NOT USE petrol or solvent as these will damage Kreepy Krauly.
IMPORTANT Kreepy Krauly must be removed from your pool during shock treatment
with chlorine or any other chemicals for at least 24 hours. If the chemicals in your pool
are too strong for people to swim in, then Kreepy Krauly should not be in the pool
either.
CAUTION: The hose must be removed for storage, store it on a flat surface.
IMPORTANT Do not use any other pool hose or automatic pool cleaner hose as the
performance of your Kreepy Krauly will be impaired. Should the hose ever require
replacement, contact your Kreepy Krauly representative and insist upon a genuine
Kreepy Krauly Hose.
KREEPY KRAULY HOSE - USE, STORAGE AND
REPLACEMENT
Your Kreepy Krauly hose is specially made because normal pool vacuum hoses do
not allow free and proper movement of Kreepy Krauly. The unique Kreepy Krauly
hose is made to be almost straight when relaxed in your pool.
Should the hose ever require replacement, contact your Kreepy Krauly
authorised consultant or service centre and insist upon a genuine
replacement Kreepy Krauly Hose.
NORMAL MAINTENANCE AND REPLACEMENT
OF WEARING PARTS
There are parts on the Kreepy Krauly which are subject to wear and tear. The
suction seal, scrubbing sole and the bumper are in direct contact with the pool
floor and wall surface. The pool owner should check the sole and bumper
regularly for wear as they protect Kreepy Krauly from damage.
Wearing parts can be easily replaced. Should Kreepy Krauly fail to function,
carefully check the entire pool system and Kreepy Krauly. If Kreepy Krauly moves
slowly with a slower than normal pulse rate and little or no water passing through
the AutoSkim valve, then the filter system should be backwashed or cleaned.
Check that operation of the vacuum plate valve is free by removing and
depressing by hand. Wash out any sand or grit. Check pump and filter for
proper operation. If the filter system is operating properly, and no part has been
damaged, blockage of the machine by extremely large leaves, nuts or other
large objects are the most common cause of the system failing to operate. Look
through the clear trap door on the main body. Remove any debris and ensure free
movement of the flow valve.
INSTALLING KREEPY KRAULY IN YOUR POOL
STEP 1 Circulation System
Thoroughly clean and backwash your filter and clean the pump, strainer and
skimmer box basket.
STEP 2 Install Kreepy Krauly
Gently sink Kreepy Krauly into pool with the hose attached below the surface,
seal first. With the pump operating place the free end of hose over a return to
pool outlet. Water will be driven through the hose and Kreepy Krauly, expelling
all air. Turn off the pump and ensure the end of the hose stays below the water
level, whilst you perform steps 3 and 4 as follows.
STEP 3 Fitting the Vacuum Control Valve
There are two basic types:
(1) Combined Vacuum Plate and AutoSkim Valve. This plate is
supplied as a replacement for your existing vacuum plate. Place the AutoSkim
valve into the opening provided in the vacuum plate ensuring it is seated
firmly. Place the combined unit into your skimmer box making sure it is seated
properly. Place the anti-vortex washer, correct side up, over the valve inlet.
Note: For some installations a retaining device such as a vacuum plate clamp
may be necessary.
“TUNED” TO YOUR POOL
Every swimming pool has individual characteristics and your Kreepy Krauly
may need to be ”tuned“ after installation. You will find many helpful hints for
minor problems in the Trouble Shooting Guide. Please try these quick and
easy remedies before calling your Kreepy Krauly service centre.
Where Kreepy Krauly has been installed by your local Authorised Kreepy
Krauly Dealer, it has been set up for maximum performance in your
pool. Please do not alter the set up characteristics without consulting the
representative who installed it.
When servicing your Kreepy Krauly, look for this seal to
ensure that the part you are buying is a certified genuine
Kreepy Krauly part.
HOW LONG SHOULD THE HOSE BE?
IMPORTANT: The pump must be on when you check the hose length. The hose
contracts when the pump is operating and will look longer than when the pump
is off.
Position the cleaner at the far end of the pool from the skimmer box. It is easy to
position the cleaner in the pool by moving it about with your pool brush.
The Sectional Hose length should be 1.5 metres longer than the
distance from the skimmer box to the far end of your pool.
Save any spare hose length for use as future replacements.
STEP 3 Connecting Hose
Fit the weighted end of the hose onto the
swivel head assembly on the other end of
the hose protector sleeve as shown.
• Under no circumstances should the
hose be stretched or picked up whilst
full of water.
• Never hang the hose from hooks.
• Always store the hose on a
flat surface.
• Do not use any other automatic pool
cleaner hose as the performance of
your Kreepy Krauly will be impaired.
IMPORTANT INFORMATION
Connect
Hose
STEP 2 Hose Weights (3)
Hose weights are fitted on the hose at
the end which will be attached to Kreepy
Krauly. The number of hose weights can
vary to suit a particular installation. A
standard three are supplied. Slide the
first hose weight approximately 1 metre
along hose. Slide the second hose weight
approximately 1.5 metres along hose.
(See the “Balance System Information”
overleaf).
Fitting Hose Weight on Hose
Hose
Weight
INSTALLING YOUR VTX3
STEP 1 Kreepy Krauly Sectional Hose
For best results and to retain your warranty and only use genuine hoses. The hose
sections need to be connected together.
Start with the male to male hose then add the male to female hoses to make the
required length. Make sure the connections are snug. The number of lengths that
you will need to join depends on the size and shape of your pool.
The overall length of hose needed will be determined by the distance from:
(a) the point at which you will attach the hose to the vacuum connection, to
(b) the furthest point from (a) ,plus one or two hose lengths.
Connecting the hose to your VTX3
Use the male to male hose section to attach the hose to the machine.
OPTIONAL ACCESSORY
If using a genuine Kreepy Krauly continuous hose,the length of the hose
required can be determined by adding 1.5 metres to the distance from vacuum
connection.
MaleFemale
Vacuum Plate Adaptor
For all Vacplates except those shown
below please use the threaded fitting
to install your KleverSkim valve. Install the threaded
fitting by screwing it into the vacplate from the top
as shown. Insert the KleverSkim valve tightly inside
the fitting. Making sure the valve can open freely.
Polyplastics Vacuum Plate Adaptor
For the Polyplastic 190 Standard and
210mm Standard Vacuum Plate (shown
left) use the Vacuum plate and insert
the KleverSkim valve into the fitting,
ensuring a tight fit.
Polyplastics Vacuum Plate Adaptor
For the SK1000 Vacuum Plate, simply
click the SK1000 fitting into the vacuum
plate and insert the KleverSkim valve
from the top.
STEP 4 How to Install the KleverSkim
Your KleverSkim Valve is designed to automatically regulate vacuum to your
Sprinta to ensure optimal operation. Depending on the Vacuum plate your
pool uses, a different KleverSkim Adaptor will be required.
NOTE: You must install your KleverSkim or the optional AutoSkim
with your Kreepy Krauly or you may void your warranty.
Ensure the water level of your pool is higher than the MiniSkim II Valve to avoid
sucking air or vortexing.
For the Poolrite plate (shown left) Install the Threaded
fitting from underneath the vacuum plate and insert the
KleverSkim from the top.
STEP 5 Connecting Hose
Connect hose to KleverSkim valve. Start
pump. Kreepy Krauly will start operating
and a soft ticking sound will be heard.