KSB Etabloc Installation instructions

Closed-coupled Pump
Etabloc
Installation/Operating Manual

Legal information/Copyright
Installation/Operating Manual Etabloc
Original operating manual
All rights reserved. The contents provided herein must neither be distributed, copied, reproduced,
edited or processed for any other purpose, nor otherwise transmitted, published or made available to a
third party without the manufacturer's express written consent.
Subject to technical modification without prior notice.
© KSB SE & Co. KGaA, Frankenthal 08/09/2022

Contents
3 of 68
Etabloc
Contents
Glossary .................................................................................................................................................. 5
1 General.................................................................................................................................................... 6
1.1 Principles ...........................................................................................................................................................6
1.2 Installation of partly completed machinery....................................................................................................6
1.3 Target group.....................................................................................................................................................6
1.4 Other applicable documents............................................................................................................................6
1.5 Symbols .............................................................................................................................................................6
1.6 Key to safety symbols/markings.......................................................................................................................7
2 Safety...................................................................................................................................................... 8
2.1 General..............................................................................................................................................................8
2.2 Intended use .....................................................................................................................................................8
2.3 Personnel qualification and training...............................................................................................................8
2.4 Consequences and risks caused by non-compliance with this manual .........................................................9
2.5 Safety awareness ..............................................................................................................................................9
2.6 Safety information for the operator/user.......................................................................................................9
2.7 Safety information for maintenance, inspection and installation ................................................................9
2.8 Unauthorised modes of operation................................................................................................................10
2.9 Explosion protection ......................................................................................................................................10
2.9.1 Marking ..............................................................................................................................................10
2.9.2 Temperature limits.............................................................................................................................10
2.9.3 Monitoring equipment......................................................................................................................11
2.9.4 Operating limits .................................................................................................................................11
3 Transport/Storage/Disposal ................................................................................................................ 12
3.1 Checking the condition upon delivery..........................................................................................................12
3.2 Transport.........................................................................................................................................................12
3.3 Storage/preservation......................................................................................................................................13
3.4 Return to supplier...........................................................................................................................................13
3.5 Disposal ...........................................................................................................................................................14
4 Description of the Pump (Set)............................................................................................................. 15
4.1 General description ........................................................................................................................................15
4.2 Product information.......................................................................................................................................15
4.2.1 Product information as per Ecodesign for Energy-Related Products Regulations 2010................15
4.2.2 Product information as per Regulation No. 1907/2006(REACH) ....................................................15
4.3 Designation.....................................................................................................................................................15
4.4 Name plate......................................................................................................................................................21
4.5 Design details..................................................................................................................................................21
4.6 Installation types ............................................................................................................................................23
4.7 Configuration and function...........................................................................................................................25
4.8 Noise characteristics .......................................................................................................................................26
4.9 Scope of supply...............................................................................................................................................26
4.10 Dimensions and weights ................................................................................................................................26
5 Installation at Site................................................................................................................................ 27
5.1 Checking the site before installation ............................................................................................................27
5.2 Installing the pump set ..................................................................................................................................27
5.3 Piping ..............................................................................................................................................................29
5.3.1 Connecting the piping.......................................................................................................................29
5.3.2 Permissible forces and moments at the pump nozzles....................................................................30
5.3.3 Vacuum balance line..........................................................................................................................30
5.3.4 Auxiliary connections.........................................................................................................................31
5.4 Enclosure/insulation .......................................................................................................................................32
5.5 Electrical connection ......................................................................................................................................32
5.5.1 Setting the time relay........................................................................................................................33

Contents
4 of 68 Etabloc
5.5.2 Earthing..............................................................................................................................................33
5.5.3 Connecting the motor .......................................................................................................................33
5.6 Checking the direction of rotation................................................................................................................33
6 Commissioning/Start-up/Shutdown................................................................................................... 35
6.1 Commissioning/Start-up.................................................................................................................................35
6.1.1 Prerequisites for commissioning/start-up .........................................................................................35
6.1.2 Priming and venting the pump.........................................................................................................35
6.1.3 Start-up...............................................................................................................................................36
6.1.4 Checking the shaft seal......................................................................................................................37
6.1.5 Shutdown ...........................................................................................................................................37
6.2 Operating limits..............................................................................................................................................38
6.2.1 Ambient temperature........................................................................................................................39
6.2.2 Frequency of starts.............................................................................................................................39
6.2.3 Fluid handled .....................................................................................................................................40
6.3 Shutdown/storage/preservation ....................................................................................................................40
6.3.1 Measures to be taken for shutdown ................................................................................................40
6.4 Returning to service .......................................................................................................................................41
7 Servicing/Maintenance........................................................................................................................ 42
7.1 Safety regulations...........................................................................................................................................42
7.2 Servicing/Inspection........................................................................................................................................43
7.2.1 Supervision of operation...................................................................................................................43
7.2.2 Inspection work..................................................................................................................................45
7.3 Drainage/cleaning ..........................................................................................................................................46
7.4 Dismantling the pump set..............................................................................................................................46
7.4.1 General information/Safety regulations...........................................................................................46
7.4.2 Preparing the pump set.....................................................................................................................47
7.4.3 Dismantling the complete pump set ................................................................................................47
7.4.4 Removing the motor..........................................................................................................................47
7.4.5 Removing the back pull-out unit ......................................................................................................48
7.4.6 Removing the impeller ......................................................................................................................48
7.4.7 Removing the mechanical seal..........................................................................................................48
7.5 Reassembling the pump set...........................................................................................................................49
7.5.1 General information/Safety regulations...........................................................................................49
7.5.2 Installing the mechanical seal ...........................................................................................................50
7.5.3 Fitting the impeller............................................................................................................................51
7.5.4 Installing the back pull-out unit .......................................................................................................51
7.5.5 Mounting the motor..........................................................................................................................51
7.6 Tightening torques.........................................................................................................................................53
7.7 Spare parts stock.............................................................................................................................................54
7.7.1 Ordering spare parts..........................................................................................................................54
7.7.2 Recommended spare parts stock ......................................................................................................55
8 Trouble-shooting.................................................................................................................................. 56
9 Related Documents.............................................................................................................................. 58
9.1 General assembly drawings ...........................................................................................................................58
9.1.1 Model with single mechanical seal and bolted casing cover ..........................................................58
9.1.2 Pump set with single mechanical seal and clamped casing cover ..................................................60
9.1.3 Version with double mechanical seal in back-to-back arrangement .............................................62
9.1.4 Version with double mechanical seal in tandem arrangement ......................................................63
10 UK Declaration of Conformity............................................................................................................. 64
11 Certificate of Decontamination........................................................................................................... 65
Index ..................................................................................................................................................... 66

Glossary
5 of 68
Etabloc
1173.87/02-EN
Glossary
ACS
French drinking water regulations (ACS =
Attestation de Conformité Sanitaire)
Back pull-out unit
Pump without pump casing; partly completed
machinery
Certificate of decontamination
A certificate of decontamination is enclosed by the
customer when returning the product to the
manufacturer to certify that the product has been
properly drained to eliminate any environmental
and health hazards arising from components in
contact with the fluid handled.
Discharge line
The pipeline which is connected to the discharge
nozzle
Hydraulic system
The part of the pump in which the kinetic energy
is converted into pressure energy
IE3
Efficiency class to IEC60034-30: 3=Premium
Efficiency (IE = International Efficiency)
Pool of pumps
Customers/operators’ pumps which are purchased
and stored regardless of their later use.
Pump
Machine without drive, additional components or
accessories
Pump set
Complete pump set consisting of pump, drive,
additional components and accessories
Suction lift line/suction head line
The pipeline which is connected to the suction
nozzle
UBA
German drinking water regulations to German
Environment Agency
WRAS
Approved by all water suppliers in the UK (WRAS =
Water Regulations Advisory Scheme)

1 General
6 of 68 Etabloc
1173.87/02-EN
1 General
1.1 Principles
This operating manual is valid for the type series and variants indicated on the front
cover.
The operating manual describes the proper and safe use of this equipment in all
phases of operation.
The name plate indicates the type series and size, the main operating data, the order
number and the order item number. The order number and order item number
clearly identify the pump set and serve as identification for all further business
processes.
In the event of damage, immediately contact your nearest KSB service facility to
maintain the right to claim under warranty.
1.2 Installation of partly completed machinery
To install partly completed machinery supplied by KSB refer to the sub-sections under
Servicing/Maintenance.
1.3 Target group
This operating manual is aimed at the target group of trained and qualified specialist
technical personnel. (ðSection2.3,Page8)
1.4 Other applicable documents
Table1: Overview of other applicable documents
Document Contents
Data sheet Description of the technical data of the pump (set)
General arrangement drawing/
outline drawing
Description of mating dimensions and installation
dimensions for the pump (set), weights
Drawing of auxiliary connections Description of auxiliary connections
Hydraulic characteristic curve Characteristic curves showing head,
NPSHrequired, efficiency and power input
General assembly drawing1) Sectional drawing of the pump
Sub-supplier product literature1) Operating manuals and other product literature
describing accessories and integrated machinery
components
Spare parts lists1) Description of spare parts
Piping layout1) Description of auxiliary piping
List of components1) Description of all pump components
Assembly drawing1) Sectional drawing of the installed shaft seal
For accessories and/or integrated machinery components, observe the relevant
manufacturer's product literature.
1.5 Symbols
Table2: Symbols used in this manual
Symbol Description
✓Conditions which need to be fulfilled before proceeding with the
step-by-step instructions
⊳Safety instructions
⇨Result of an action
⇨Cross-references
1If included in agreed scope of supply

1 General
7 of 68
Etabloc
1173.87/02-EN
Symbol Description
1.
2.
Step-by-step instructions
Note
Recommendations and important information on how to handle
the product
1.6 Key to safety symbols/markings
Table3: Definition of safety symbols/markings
Symbol Description
!DANGER
DANGER
This signal word indicates a high-risk hazard which, if not avoided,
will result in death or serious injury.
!WARNING
WARNING
This signal word indicates a medium-risk hazard which, if not
avoided, could result in death or serious injury.
CAUTION
CAUTION
This signal word indicates a hazard which, if not avoided, could
result in damage to the machine and its functions.
Explosion protection
This symbol identifies information about avoiding explosions in
potentially explosive atmospheres in accordance with the UK
regulation titled Equipment and Protective Systems Intended for
Use in Potentially Explosive Atmospheres Regulations 2016.
General hazard
In conjunction with one of the signal words this symbol indicates a
hazard which will or could result in death or serious injury.
Electrical hazard
In conjunction with one of the signal words this symbol indicates a
hazard involving electrical voltage and identifies information about
protection against electrical voltage.
Machine damage
In conjunction with the signal word CAUTION this symbol indicates
a hazard for the machine and its functions.

2 Safety
8 of 68 Etabloc
1173.87/02-EN
2 Safety
!DANGER
All the information contained in this section refers to hazardous situations.
In addition to the present general safety information the action-related safety
information given in the other sections must be observed.
2.1 General
▪This operating manual contains general installation, operating and maintenance
instructions that must be observed to ensure safe operation of the system and
prevent personal injury and damage to property.
▪Comply with all the safety instructions given in the individual sections of this
operating manual.
▪The operating manual must be read and understood by the responsible specialist
personnel/operators prior to installation and commissioning.
▪The contents of this operating manual must be available to the specialist
personnel at the site at all times.
▪Information and markings attached directly to the product must always be
complied with and kept in a perfectly legible condition at all times. This applies
to, for example:
– Arrow indicating the direction of rotation
– Markings for connections
– Name plate
▪The operator is responsible for ensuring compliance with all local regulations not
taken into account.
2.2 Intended use
▪The pump (set) must only be operated in the fields of application and within the
use limits specified in the other applicable documents.
▪Only operate pumps/pump sets which are in perfect technical condition.
▪Do not operate the pump (set) in partially assembled condition.
▪Only use the pump (set) to handle the fluids described in the data sheet or
product literature of the pump variant.
▪Never operate the pump (set) without the fluid to be handled.
▪Observe the minimum flow rate and maximum flow rate indicated in the data
sheet or product literature (to prevent overheating, mechanical seal damage,
cavitation damage, bearing damage, etc).
▪Always operate the pump (set) in the direction of rotation it is intended for.
▪Do not throttle the flow rate on the suction side of the pump (to prevent
cavitation damage).
▪Consult the manufacturer about any use or mode of operation not described in
the data sheet or product literature.
2.3 Personnel qualification and training
All personnel involved must be fully qualified to transport, install, operate, maintain
and inspect the machinery this manual refers to.
The responsibilities, competence and supervision of all personnel involved in
transport, installation, operation, maintenance and inspection must be clearly
defined by the operator.
Deficits in knowledge must be rectified by means of training and instruction
provided by sufficiently trained specialist personnel. If required, the operator can
commission the manufacturer/supplier to train the personnel.
Training on the pump (set) must always be supervised by technical specialist
personnel.

2 Safety
9 of 68
Etabloc
1173.87/02-EN
2.4 Consequences and risks caused by non-compliance with this manual
▪Non-compliance with these operating instructions will lead to forfeiture of
warranty cover and of any and all rights to claims for damages.
▪Non-compliance can, for example, have the following consequences:
– Hazards to persons due to electrical, thermal, mechanical and chemical
effects and explosions
– Failure of important product functions
– Failure of prescribed maintenance and servicing practices
– Hazard to the environment due to leakage of hazardous substances
2.5 Safety awareness
In addition to the safety information contained in this operating manual and the
intended use, the following safety regulations shall be complied with:
▪Accident prevention, health regulations and safety regulations
▪Explosion protection regulations
▪Safety regulations for handling hazardous substances
▪Applicable standards, directives and laws
2.6 Safety information for the operator/user
▪Fit protective equipment (e.g. contact guards) supplied by the operator for hot,
cold or moving parts, and check that the equipment functions properly.
▪Do not remove any protective equipment (e.g. contact guards) during operation.
▪Provide the personnel with protective equipment and make sure it is used.
▪Contain leakages (e.g. at the shaft seal) of hazardous fluids handled (e.g.
explosive, toxic, hot) so as to avoid any danger to persons and the environment.
Adhere to all relevant laws.
▪Eliminate all electrical hazards. (In this respect refer to the applicable national
safety regulations and/or regulations issued by the local energy supply
companies.)
▪If stopping the pump does not increase potential risk, fit an emergency-stop
control device in the immediate vicinity of the pump (set) during pump set
installation.
2.7 Safety information for maintenance, inspection and installation
▪Modifications or alterations of the pump (set) are only permitted with the
manufacturer's prior consent.
▪Use only original spare parts or parts/components authorised by the
manufacturer. The use of other parts/components can invalidate any liability of
the manufacturer for resulting damage.
▪The operator ensures that maintenance, inspection and installation are
performed by authorised, qualified specialist personnel who are thoroughly
familiar with the manual.
▪Only carry out work on the pump (set) during standstill of the pump.
▪Only perform work on the pump set when it has been disconnected from the
power supply (de-energised).
▪The pump (set) must have cooled down to ambient temperature.
▪Pump pressure must have been released and the pump must have been drained.

2 Safety
10 of 68 Etabloc
1173.87/02-EN
▪When taking the pump set out of service always adhere to the procedure
described in the manual. (ðSection6.1.5,Page37) (ðSection6.3,Page40)
▪Decontaminate pumps which handle fluids posing a health hazard.
▪As soon as the work has been completed, re-install and re-activate any safety-
relevant devices and protective devices. Before returning the product to service,
observe all instructions on commissioning. (ðSection6.1,Page35)
2.8 Unauthorised modes of operation
Never operate the pump (set) outside the limits stated in the data sheet and in this
operating manual.
The warranty relating to the operating reliability and safety of the pump (set)
supplied is only valid if the equipment is used in accordance with its intended use.
(ðSection2.2,Page8)
2.9 Explosion protection
!DANGER
Always observe the information on explosion protection given in this section when
operating the product in potentially explosive atmospheres.
Pumps/Pump sets must not be used in potentially explosive atmospheres unless
marked as explosion-proof and identified as such in the data sheet.
Special conditions apply to the operation of explosion-proof pump sets in accordance
with the UK's Equipment and Protective Systems Intended for Use in Potentially
Explosive Atmospheres Regulations 2016.
Especially adhere to the sections in this manual marked with the Ex symbol and the
following sections, (ðSection2.9.1,Page10) to (ðSection2.9.4,Page11)
The explosion-proof status of the pump is only assured if the pump is used in
accordance with its intended use.
Never operate the product outside the limits stated in the data sheet and on the
name plate.
Prevent impermissible modes of operation at all times.
2.9.1 Marking
Pump The marking on the pump refers to the pump part only.
Example of such marking:
II 2G Ex h IIC T5-T1 Gb
Refer to the Temperature limits table for the maximum temperatures permitted for
the individual pump variants. (ðSection2.9.2,Page10)
The pump complies with the requirements of type of protection constructional safety
"c" to ISO80079-37.
Shaft coupling An EC manufacturer's declaration is required for the shaft coupling; the shaft
coupling must be marked accordingly.
Motor The motor has its own marking. The marking is maintained on the condition that the
temperatures the pump causes to develop at the motor flange and motor shaft are
permitted by the motor manufacturer.
The motors fitted by KSB on pumps certified for potentially explosive atmospheres
meet this condition.
Misuse, malfunctions or non-compliance with the instructions may result in
substantially higher temperatures.
2.9.2 Temperature limits
In normal pump operation, the highest temperatures are to be expected on the
surface of the pump casing and at the shaft seal.
The surface temperature at the pump casing corresponds to the temperature of the
fluid handled. If the pump is heated in addition, the operator of the system is
responsible for observing the specified temperature class and fluid temperature
(operating temperature).

2 Safety
11 of 68
Etabloc
1173.87/02-EN
The table (ðTable4) lists the temperature classes and the resulting maximum
permissible fluid temperatures. The values shown correspond to the theoretical
limits. They include only a general safety margin for the mechanical seal. For single
mechanical seals, the safety margin required for specific operating conditions and
mechanical seal designs may be substantially higher. If operating conditions differ
from those stated on the data sheet, or if different mechanical seals are used, the
actual safety margin required needs to be determined individually. If in doubt please
contact the manufacturer.
The temperature class specifies the maximum permissible temperature at the surface
of the pump set during operation. For the permissible operating temperature of the
pump in question refer to the data sheet.
Table4: Temperature limits
Temperature class to ISO80079-36 Maximum permissible
fluid temperature2)
T1 Temperature limit of the pump
T2 280°C
T3 185°C
T4 120°C
T5 85°C
T6 Only after consultation
with the manufacturer
If the pump is to be operated at a higher temperature, the data sheet is missing or if
the pump is part of a pool of pumps, contact KSB for the maximum permissible
operating temperature.
Motor supplied by the
operator
If a pump is supplied without motor (as part of a pool of pumps), the motor specified
in the pump data sheet must meet the following conditions:
▪The permissible temperature limits at the motor flange and motor shaft must be
higher than the temperatures generated by the pump.
▪Contact the manufacturer for the actual pump temperatures.
2.9.3 Monitoring equipment
The pump (set) must only be operated within the limits specified in the data sheet
and on the name plate.
If the system operator cannot warrant compliance with these operating limits,
appropriate monitoring devices must be used.
Check whether monitoring equipment is required to ensure that the pump set
functions properly.
Contact KSB for further information about monitoring equipment.
2.9.4 Operating limits
The minimum flow rates indicated in (ðSection6.2.3.1,Page40) refer to water
and water-like fluids handled. Longer operating periods with these fluids and at the
flow rates indicated will not cause an additional increase in the temperatures at the
pump surface. However, if the physical properties of the fluids handled are different
from water, it is essential to check whether an additional heat build-up may occur
and if the minimum flow rate must therefore be increased. The calculation formula
in (ðSection6.2.3.1,Page40) can be used to check whether an additional heat
build-up may lead to a dangerous temperature increase at the pump surface.
2Subject to further limitations for mechanical seal temperature rise

3 Transport/Storage/Disposal
12 of 68 Etabloc
1173.87/02-EN
3 Transport/Storage/Disposal
3.1 Checking the condition upon delivery
1. On transfer of goods, check each packaging unit for damage.
2. In the event of in-transit damage, assess the exact damage, document it and
notify KSB or the supplying dealer and the insurer about the damage in writing
immediately.
3.2 Transport
DANGER
The pump (set) could slip out of the suspension arrangement
Danger to life from falling parts!
▷Always transport the pump (set) in the specified position.
▷Never attach the suspension arrangement to the free shaft end or the motor
eyebolt.
▷Observe the information about weights, centre of gravity and fastening points.
▷Observe the applicable local accident prevention regulations.
▷Use suitable, permitted lifting accessories, e.g. self-tightening lifting tongs.
CAUTION
Incorrect transport of the pump
Damage to the shaft seal!
▷For transport, lock the pump shaft with a suitable transport lock to prevent any
movement of the shaft.
When transporting the pump without motor, shaft 210 must be locked.
1. Remove cover plates 68-3 from the openings of drive lantern 341.
2. Insert lock washers 931.95 into the shaft groove.
3. Tighten bolts 901.50.
To transport the pump/pump set suspend it from the lifting tackle as shown.
Fig.1: Transporting the pump
Fig.2: Transporting the pump set

3 Transport/Storage/Disposal
13 of 68
Etabloc
1173.87/02-EN
≤ 90°
Fig.3: Transporting the pump set on the baseplate
3.3 Storage/preservation
CAUTION
Damage during storage due to humidity, dirt or vermin
Corrosion/contamination of pump (set)!
▷For outdoor storage cover the pump (set) and accessories with waterproof
material and protect against condensation.
CAUTION
Wet, contaminated or damaged openings and connections
Leakage or damage to the pump!
▷Clean and cover pump openings and connections as required prior to putting
the pump into storage.
If commissioning is to take place some time after delivery, we recommend that the
following measures be taken for pump (set) storage.
▪Store the pump (set) in a dry, protected room where the atmospheric humidity is
as constant as possible.
▪Rotate the shaft by hand once a month, e.g. via the motor fan.
If properly stored indoors, the pump set is protected for a maximum of 12 months.
New pumps/pump sets are supplied by our factory duly prepared for storage.
For storing a pump (set) which has already been operated, the shutdown measures
must be adhered to. (ðSection6.3.1,Page40)
3.4 Return to supplier
1. Drain the pump as per operating instructions.
2. Flush and clean the pump, particularly if it has been used for handling noxious,
explosive, hot or other hazardous fluids.
3. If the pump has handled fluids whose residues could lead to corrosion damage
in the presence of atmospheric humidity or could ignite upon contact with
oxygen, the pump must also be neutralised, and anhydrous inert gas must be
blown through the pump to ensure drying.
4. Always complete and enclose a certificate of decontamination when returning
the pump.
Indicate any safety measures and decontamination measures taken.
(ðSection11,Page65)
NOTE
If required, a blank certificate of decontamination can be downloaded from the
following web site: www.ksb.com/certificate_of_decontamination

3 Transport/Storage/Disposal
14 of 68 Etabloc
1173.87/02-EN
3.5 Disposal
WARNING
Fluids handled, consumables and supplies which are hot and/or pose a health
hazard
Hazard to persons and the environment!
▷Collect and properly dispose of flushing fluid and any fluid residues.
▷Wear safety clothing and a protective mask if required.
▷Observe all legal regulations on the disposal of fluids posing a health hazard.
1. Dismantle the pump (set).
Collect greases and other lubricants during dismantling.
2. Separate and sort the pump materials, e.g. by:
- Metals
- Plastics
- Electronic waste
- Greases and other lubricants
3. Dispose of materials in accordance with local regulations or in another
controlled manner.

4 Description of the Pump (Set)
15 of 68
Etabloc
1173.87/02-EN
4 Description of the Pump (Set)
4.1 General description
▪Centrifugal pump with shaft seal
▪Close-coupled design
▪Handling clean or aggressive fluids not chemically and mechanically aggressive to
the pump materials.
4.2 Product information
4.2.1 Product information as per Ecodesign for Energy-Related Products Regulations
2010
▪Minimum efficiency index: see name plate, key to name plate
▪The benchmark for the most efficient water pumps is MEI ≥ 0.70.
▪Year of construction: see name plate, key to name plate
▪Manufacturer’s name or trade mark, commercial registration number and place
of manufacture: see data sheet or order documentation
▪Product’s type and size identificator: see name plate, key to name plate
▪Hydraulic pump efficiency (%) with trimmed impeller: see data sheet
▪Pump performance curves, including efficiency characteristics: see documented
characteristic curve
▪The efficiency of a pump with a trimmed impeller is usually lower than that of a
pump with the full impeller diameter. Trimming of the impeller will adapt the
pump to a fixed duty point, leading to reduced energy consumption. The
minimum efficiency index (MEI) is based on the full impeller diameter.
▪Operation of this water pump with variable duty points may be more efficient
and economic when controlled, for example, by the use of a variable speed drive
that matches the pump duty to the system.
▪Information on dismantling, recycling and disposal after decommissioning:
(ðSection3.5,Page14)
▪Information on benchmark efficiency or benchmark efficiency graph for
MEI=0.70(0.40) for the pump based on the model shown in the Figure are
available at: http://www.europump.org/efficiencycharts
4.2.2 Product information as per Regulation No. 1907/2006(REACH)
For information as per chemicals Regulation (EC) No. 1907/2006 (REACH), see https://
www.ksb.com/ksb-en/About-KSB/Corporate-responsibility/reach/ .
4.3 Designation
Refer to position 26 to correctly interpret the designation.
If a number is specified, go to the 1st designation example. (ðTable5)
If a letter is specified, go to the 2nd designation example. (ðTable7)
Table5: 1st designation example
Position
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38
E T B - 0 4 0 - 0 2 5 - 1 6 0 - G G S A V 6 7 D 2 1 1 0 0 2 - - B P D 2 E M
See name plate and data sheet See data sheet -
Table6: Designation key
Position Code Description
1-4 Pump type
ETB Etabloc

4 Description of the Pump (Set)
16 of 68 Etabloc
1173.87/02-EN
Position Code Description
1-4 ETBF Etabloc bottle rinser variant
5-16 Size [mm], e.g.
040 Nominal suction nozzle diameter
025 Nominal discharge nozzle diameter
160 Nominal impeller diameter
17 Pump casing material
B Bronze CC480K-GS/ B30 C90700
C Stainless steel 1.4408/ A743CF8M
G Cast iron EN-GJL-250/ A48 Cl. 35B
S Nodular cast iron Nodular cast iron EN-GJS-400-15/
A536Gr.60-40-18
18 Impeller material
B Bronze CC480K-DW
C Stainless steel 1.4408/ A743CF8M
G Cast iron EN-GJL-250/ A48 Cl. 35B
19 Design
E European Regulation (EC) No. 1935/2004
F Bottle rinser variant
H Approved for drinking water to ACS
K Approved for drinking water to KSB standard
P Swimming pool variant
R Gohl (special design)
S Standard
U Approved for drinking water to UBA
W Approved for drinking water to WRAS
X Non-standard (BT3D, BT3)
20 Casing cover
A Conical seal chamber
C Cylindrical seal chamber
21 Shaft seal type
D Double mechanical seal in back-to-back arrangement
E Single mechanical seal, external circulation
F Single mechanical seal, external flushing
I Single mechanical seal, internal circulation, conical cover (A-type
cover) only
S Single mechanical seal with vented chamber (A-type cover),
discharge cover with anti-swirl baffles
T Double mechanical seal in tandem arrangement with internal
circulation
V Single mechanical seal with vented chamber (A-type cover)
22-23 Seal code, single mechanical seal
01 Q1Q1VGG 1 (ZN1181) ≥ -20 - ≤ +110 [°C]
06 U3BEGG (shaft units 25, 35) RMG13G606 ≥ -30 - ≤ +140 [°C]
07 Q1Q1EGG 1A (ZN1181) ≥ -30 - ≤ +110 [°C]
08 AQ1VGG M32N69 ≥ -30 - ≤ +110 [°C]
09 U3U3VGG MG13G60 ≥ -20 - ≤ +110 [°C]
10 Q1Q1X4GG 1 (ZN1181) ≥ -20 - ≤ +110 [°C]
11 BQ1EGG-WA (WA = drinking
water)
1 (ZN1181) ≥ -30 - ≤ +110 [°C]
12 Q12Q1M1GG1 M37GN83 ≥ -20 - ≤ +100 [°C]

4 Description of the Pump (Set)
17 of 68
Etabloc
1173.87/02-EN
Position Code Description
22-23 13 BQ1VGG 1 (ZN1181) ≥ -20 - ≤ +110 [°C]
14 Q1Q1KY7G KMB13S2G9 ≥ -20 - ≤ +120 [°C]
15 Q1Q1KGG M7G49 ≥ -20 - ≤ +110 [°C]
16 BVPGG MG1S20 ≥ -20 - ≤ +110 [°C]
17 Q1BVGG M7N ≥ -20 - ≤ +110 [°C]
22 AQ1EGG (shaft unit 55) M32N69 ≥ -30 - ≤ +140 [°C]
66 Q7Q7EGG MG13G6 ≥ -30 - ≤ +120 [°C]
67 Q6Q6X4GG MG13G60 /
MG1G61S6
≥ -20 - ≤ +110 [°C]
Seal code, double mechanical seal in tandem arrangement
18 Q1Q1EGG/G MG12G6-E1 ≥ -30 - ≤ +110 [°C]
Q1Q1EGG-G MG12G6-E1 ≥ -30 - ≤ +110 [°C]
19 Q1Q1M1GG HN400N ≥ -30 - ≤ +110 [°C]
Q1Q1EGG-G MG12G6-E1 ≥ -30 - ≤ +110 [°C]
20 Q12Q1M1GG1 M37GN85 ≥ -20 - ≤ +110 [°C]
Q1Q1EGG-G MG12G6-E1 ≥ -20 - ≤ +110 [°C]
23 Q12Q1M1GG1 M37GN92 ≥ -20 - ≤ +110 [°C]
Q1Q1EGG-G MG12G6-E1 ≥ -20 - ≤ +110 [°C]
Seal code, double mechanical seal in back-to-back arrangement
21 Q1Q1KGG M7G49 ≥ -20 - ≤ +110 [°C]
Q1Q1KGG M7G49 ≥ -20 - ≤ +110 [°C]
24 Q1Q1KGG M7G49 ≥ -20 - ≤ +110 [°C]
Q1BVGG M7N ≥ -20 - ≤ +110 [°C]
Seal code without mechanical seal
99 Shaft seal ring, variant Gohl
24 Scope of supply
A Pump only (Fig.0)
D Pump, motor
G Pump, baseplate
E Pump, back pull-out unit
25 Shaft unit
2 Shaft unit 25
3 Shaft unit 35
5 Shaft unit 55
26-29 Motor rating PN [kW]
0075 7,5
0300 30
1100 110
30 Number of motor poles
2 2 poles
4 4 poles
6 6 poles
31-32 Explosion protection
ex With explosion-proof motor
-- Without explosion-proof motor
33 Product generation
B Etabloc
34-37 Description
- Fixed speed version
PD2 Variable speed version, with PumpDrive2

4 Description of the Pump (Set)
18 of 68 Etabloc
1173.87/02-EN
Position Code Description
34-37 PD2E Variable speed version, with PumpDrive2Eco
IFS MyFlowDrive
38 PumpMeter
M PumpMeter
Table7: 2nd designation example
Position
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
E T B 0 4 0 - 0 2 5 - 1 6 0 - G G S B E 1 1 W S E J B 2 H C B
See name plate and data sheet
Table8: Designation key
Position Code Description
1-4 Pump type
ETB Etabloc
ETBF Etabloc bottle rinser variant
5-16 Size [mm], e.g.
040 Nominal suction nozzle diameter
025 Nominal discharge nozzle diameter
160 Nominal impeller diameter
17 Pump casing material
B Bronze CC480K-GS / B30 C90700
C Stainless steel 1.4408 / A743CF8M
G Cast iron EN-GJL-250 / A48CL35
K Cast iron, electrocoated EN-GJL-250, electrocoated
S Nodular cast iron EN-GJS-400-15 /
A536Gr.60-40-18
18 Impeller material
B Bronze CC480K-GS / B30 C90700
C Stainless steel 1.4408 / A743CF8M
G Cast iron EN-GJL-250 / A48CL35
P Cast iron without protective
coating
EN-GJL-250 without protective
coating
19 Design
E Design as per European Regulation (EC) No. 1935/2004
F Bottle rinser variant
H Approved for drinking water to ACS
K Approved for drinking water to KSB standard
P Swimming pool variant
S Standard
U Approved for drinking water to UBA
W Approved for drinking water to WRAS
20 Casing cover connections
B Conical casing cover with connection for venting
C Conical casing cover with vent
D Conical casing cover with connection for external flushing
E Conical casing cover with connection for external flushing from
discharge nozzle
H Cylindrical casing cover for version with double mechanical seal in
tandem arrangement with connection for quench system

4 Description of the Pump (Set)
19 of 68
Etabloc
1173.87/02-EN
Position Code Description
20 I Cylindrical casing cover for version with double mechanical seal in
back-to-back arrangement with connection for barrier fluid
system
21 Shaft seal type
D Double mechanical seal in back-to-back arrangement
E Single mechanical seal, external circulation, conical casing cover
F Single mechanical seal, external flushing, conical casing cover
T Double mechanical seal in tandem arrangement with internal
circulation
V Single mechanical seal with vented chamber (A-type cover)
22-23 Seal code, single mechanical seal
01 Q1Q1VGG 1 (ZN1181) ≥ -20 - ≤ +110 [°C]
06 U3BEGG RMG13G606 ≥ -30 - ≤ +140 [°C]
07 Q1Q1EGG 1A (ZN1181) ≥ -30 - ≤ +110 [°C]
08 AQ1VGG M32N69 ≥ -30 - ≤ +110 [°C]
09 U3U3VGG MG13G60 ≥ -20 - ≤ +110 [°C]
10 Q1Q1X4GG 1 (ZN1181) ≥ -20 - ≤ +110 [°C]
11 BQ1EGG-WA 1 (ZN1181) ≥ -30 - ≤ +110 [°C]
12 Q12Q1M1GG1 M37GN83 ≥ -20 - ≤ +100 [°C]
13 BQ1VGG 1 (ZN1181) ≥ -20 - ≤ +110 [°C]
14 Q1Q1KY7G KMB13S2G9 ≥ -20 - ≤ +120 [°C]
15 Q1Q1KGG M7G49 ≥ -20 - ≤ +110 [°C]
16 BVPGG MG1S20 ≥ -20 - ≤ +110 [°C]
17 Q1BVGG M7N / 5A ≥ -20 - ≤ +110 [°C]
22 AQ1EGG M32N69 ≥ -30 - ≤ +140 [°C]
45 BQ7E1/Y10GG EMG13G6 ≥ -30 - ≤ +110 [°C]
46 Q7Q7E1/Y10GG EMG13G6 ≥ -30 - ≤ +110 [°C]
51 BQ7V16GG/Y10 EMG13G6 ≥ -14 - ≤ +120 [°C]
52 Q7Q7V16GG/Y10 EMG13G6 ≥ -14 - ≤ +120 [°C]
66 Q7Q7EGG MG13G6 ≥ -30 - ≤ +120 [°C]
67 Q6Q6X4GG MG13G60 /
MG1G61S6
≥ -20 - ≤ +110 [°C]
Seal code, double mechanical seal in tandem arrangement
18 Q1Q1EGG/G MG12G6-E1 ≥ -30 - ≤ +110 [°C]
Q1Q1EGG-G MG12G6-E1 ≥ -30 - ≤ +110 [°C]
20 Q12Q1M1GG1 M37GN85 ≥ -20 - ≤ +110 [°C]
Q1Q1EGG-G MG12G6-E1 ≥ -20 - ≤ +110 [°C]
23 Q12Q1M1GG1 M37GN92 ≥ -20 - ≤ +110 [°C]
Q1Q1EGG-G MG12G6-E1 ≥ -20 - ≤ +110 [°C]
Seal code, double mechanical seal in back-to-back arrangement
21 Q1Q1KGG M7G49 ≥ -20 - ≤ +110 [°C]
Q1Q1KGG M7G49 ≥ -20 - ≤ +110 [°C]
24 Q1Q1KGG M7G49 ≥ -20 - ≤ +110 [°C]
Q1BVGG M7N ≥ -20 - ≤ +110 [°C]
24 Type of lubrication
W None
25 Order type
C Extended standard
S KSB standard
X Special design

4 Description of the Pump (Set)
20 of 68 Etabloc
1173.87/02-EN
Position Code Description
26 Bearing bracket/ Shaft unit
E Shaft unit 25
F Shaft unit 35
H Shaft unit 55
27-28 Motor rating PN [kW]
AJ 0,37
... ...
KP 160
29 Number of motor poles
2 2 poles
4 4 poles
6 6 poles
30 Scope of supply
A Bare-shaft pump
G Back pull-out unit
H Pump, motor
31 Accessories/ Automation
A KSBPumpDrive 2
B KSBPumpMeter
C KSBPumpDrive 2 + KSBPumpMeter
D IFS
E KSBGuard
F Han-Drive10E
G Han-Drive10E + KSBPumpMeter
H None
I Version for potentially explosive atmospheres
J KSBPumpDrive 2 + KSBGuard
K KSBPumpMeter 2 + KSBGuard
L KSBPumpDrive 2 + KSBPumpMeter + KSBGuard
32 Product generation
B Generation B