Kubota V3300-E2B Instruction manual

WORKSHOP MANUAL
DIESEL ENGINE
V3300-E2B,V3300-T-E2B
KiSC issued 06, 2006 A

TO THE READER
This Workshop Manual has been prepared to provide servicing personnel with
information on the mechanism, service and maintenance of V3300-E2B, V3300-T-E2B.
It is divided into three parts, “General”, “Mechanism” and “Servicing”.
■General
Information on the engine identification, the general precautions, maintenance check
list, check and maintenance and special tools are described.
■Mechanism
Information on the construction and function are included. This part should be
understood before proceeding with troubleshooting, disassembling and servicing.
Refer to Diesel Engine Mechanism Workshop Manual (Code No. 9Y021-01870) for
the one which has not been described to this workshop manual.
■Servicing
Information on the troubleshooting, servicing specification lists, tightening torque,
checking and adjusting, disassembling and assembling, and servicing which cover
procedures, precautions, factory specifications and allowable limits.
All information illustrations and specifications contained in this manual are based on
the latest product information available at the time of publication.
The right is reserved to make changes in all information at any time without notice.
Due to covering many models of this manual, information or picture being used have
not been specified as one model.
March 2004
© KUBOTA Corporation 2004
KiSC issued 06, 2006 A

1
V3300-E2B, V3300-T-E2B, WSM SAFETY INSTRUCTIONS
SAFETY INSTRUCTIONS
BEFORE SERVICING AND REPAIRING
• Read all instructions and safety instructions in this
manual and on your engine safety decals.
• Clean the work area and engine.
• Park the machine on a firm and level ground.
• Allow the engine to cool before proceeding.
• Stop the engine, and remove the key.
• Disconnect the battery negative cable.
• Hang a “DO NOT OPERATE” tag in operator
station.
SAFETY FIRST
This symbol, the industry’s “Safety Alert Symbol”, is used throughout this manual and on labels on
the machine itself to warn of the possibility of personal injury. Read these instructions carefully.
It is essential that you read the instructions and safety regulations before you attempt to repair or use
this unit.
DANGER : Indicates an imminently hazardous situation which, if not avoided, will result in
death or serious injury.
WARNING : Indicates a potentially hazardous situation which, if not avoided, could result in
death or serious injury.
CAUTION : Indicates a potentially hazardous situation which, if not avoided, may result in
minor or moderate injury.
■IMPORTANT : Indicates that equipment or property damage could result if instructions are not
followed.
■NOTE : Gives helpful information.
KiSC issued 06, 2006 A

2
V3300-E2B, V3300-T-E2B, WSM SAFETY INSTRUCTIONS
SAFETY STARTING
• Do not start the engine by shorting across starter
terminals or bypassing the safety start switch.
• Unauthorized modifications to the engine may impair
the function and / or safety and affect engine life.
SAFETY WORKING
• Do not work on the machine while under the influence
of alcohol, medication, or other substances or while
fatigued.
• Wear close fitting clothing and safety equipment
appropriate to the job.
• Use tools appropriate to the work. Makeshift tools,
parts, and procedures are not recommended.
• When servicing is performed together by two or more
persons, take care to perform all work safely.
• Do not touch the rotating or hot parts while the engine
is running.
• Never remove the radiator cap while the engine is
running, or immediately after stopping. Otherwise, hot
water will spout out from radiator. Only remove
radiator cap when cool enough to touch with bare
hands. Slowly loosen the cap to first stop to relieve
pressure before removing completely.
• Escaping fluid (fuel or hydraulic oil) under pressure
can penetrate the skin causing serious injury. Relieve
pressure before disconnecting hydraulic or fuel lines.
Tighten all connections before applying pressure.
• Wear a suitable hearing protective device such as
earmuffs or earplugs to protect against objectionable
or uncomfortable loud noises.
AVOID FIRES
• Fuel is extremely flammable and explosive under
certain conditions. Do not smoke or allow flames or
sparks in your working area.
• To avoid sparks from an accidental short circuit,
always disconnect the battery negative cable first and
connect it last.
• Battery gas can explode. Keep sparks and open
flame away from the top of battery, especially when
charging the battery.
• Make sure that no fuel has been spilled on the engine.
KiSC issued 06, 2006 A

3
V3300-E2B, V3300-T-E2B, WSM SAFETY INSTRUCTIONS
VENTILATE WORK AREA
• If the engine must be running to do some work, make
sure the area is well ventilated. Never run the engine
in a closed area. The exhaust gas contains poisonous
carbon monoxide.
DISPOSE OF FLUIDS PROPERLY
• Do not pour fluids into the ground, down a drain, or
into a stream, pond, or lake. Observe relevant
environmental protection regulations when disposing
of oil, fuel, coolant, electrolyte and other harmful
waste.
PREVENT ACID BURNS
• Sulfuric acid in battery electrolyte is poisonous. It is
strong enough to burn skin, clothing and cause
blindness if splashed into eyes. Keep electrolyte
away from eyes, hands and clothing. If you spill
electrolyte on yourself, flush with water, and get
medical attention immediately.
PREPARE FOR EMERGENCIES
• Keep a first aid kit and fire extinguisher handy at all
times.
• Keep emergency numbers for doctors, ambulance
service, hospital and fire department near your
telephone.
KiSC issued 06, 2006 A

4
V3300-E2B, V3300-T-E2B, WSM SPECIFICATIONS
SPECIFICATIONS
* The specification described above is of the standard engine of each model.
* Conversion Formula : HP = 0.746 kW, PS = 0.7355 kW W1028103
Model V3300-E2B V3300-T-E2B
Number of Cylinder 4
Type Vertical, water-cooled, 4-cycle diesel engine
Bore ×Stroke 98 ×110 mm (3.86 ×4.33 in.)
Total Displacement 3318 cm3(202.48 cu.in.)
ISO Net Continuous 44.1 kW / 2600 min-1 (rpm)
(59.1 HP / 2600 min-1 (rpm)) 53.8 kW / 2600 min-1 (rpm) (72.1 HP / 2600 min-1 (rpm))
ISO / SAE Net Intermittent 50.7 kW / 2600 min-1 (rpm)
(68.0 HP / 2600 min-1 (rpm)) 61.9 kW / 2600 min-1 (rpm) (83.0 HP / 2600 min-1 (rpm))
SAE Gross Intermittent 54.5 kW / 2600 min-1 (rpm)
(73.0 HP / 2600 min-1 (rpm)) 65.2 kW / 2600 min-1 (rpm) (87.4 HP / 2600 min-1 (rpm))
DIN6271-NA 44.6 kW / 2600 min-1 (rpm)
(59.8 ps / 2600 min-1 (rpm)) 53.8 kW / 2600 min-1 (rpm) (73.1 ps / 2600 min-1 (rpm))
DIN6271-NB 48.9 kW / 2600 min-1 (rpm)
(66.5 ps / 2600 min-1 (rpm)) 59.7 kW / 2600 min-1 (rpm) (81.2 ps / 2600 min-1 (rpm))
DIN70020 52.7 kW / 2600 min-1 (rpm)
(71.7 ps / 2600 min-1 (rpm)) 64.4 kW / 2600 min-1 (rpm) (87.6 ps / 2600 min-1 (rpm))
Maximum Bare Speed 2800 min-1 (rpm)
Minimum Bare Idling Speed 700 to 750 min-1 (rpm)
Combustion Chamber Spherical Type (E-TVCS)
Fuel Injection Pump Bosch Type Mini Pump
Governor All speed mechanical governor
Direction of Rotation Counter-clockwise (Viewed from flywheel side)
Injection Nozzle BOSCH Throttle-Type
Injection Timing 0.21 rad. (12 °) before T.D.C. 0.12 rad. (7 °) before T.D.C.
Firing Order 1-3-4-2
Injection Pressure 13.73 MPa (140 kgf/cm2, 1991 psi)
Compression Ratio 22.6 21.8
Lubricating System Forced lubrication by trochoid pump
Oil Pressure Indicating Electrical Type Switch
Lubricating Filter Full Flow Paper Filter (Cartridge Type)
Cooling System Pressurized radiator, forced circulation with water pump
Starting System Electric Starting with Starter
Starting Motor 12 V, 2.5 kW
Starting Support Device By Glow Plug in Combustion Chamber
Battery 12 V, 112 AH equivalent
Charging Alternator 12 V, 540 W
Fuel Diesel Fuel No. 2-D (ASTM D975)
Lubricating Oil Class CF lubricating oil as per API classification is recommended. If this class of lubricating oil is not available, preferably use Class CD or CE lubricating oil.
For details on recommended lubricating oils, see page G-5, 11.
Lubricating Oil Capacity 13.2 L (3.49 U.S.gals)
Weight (Dry) 241 kg (531 lbs) 250 kg (551 lbs)
KiSC issued 06, 2006 A

5
V3300-E2B, V3300-T-E2B, WSM PERFORMANCE CURVES
PERFORMANCE CURVES
(1) Brake Horsepower
(2) Engine Speed
(3) B.S.F.C.
(4) Torque
(5) Gross Intermittent Torque
(6) Net Intermittent Torque
(7) Net Continuous Torque
(8) Gross Intermittent B.H.P.
(9) Net Intermittent B.H.P.
(10) Net Continuous B.H.P.
(11) B.S.F.C. (Net Intermittent)
KiSC issued 06, 2006 A

6
V3300-E2B, V3300-T-E2B, WSM PERFORMANCE CURVES
(1) Brake Horsepower
(2) Engine Speed
(3) B.S.F.C.
(4) Torque
(5) Gross Intermittent Torque
(6) Net Intermittent Torque
(7) Net Continuous Torque
(8) Gross Intermittent B.H.P.
(9) Net Intermittent B.H.P.
(10) Net Continuous B.H.P.
(11) B.S.F.C. (Net Intermittent)
KiSC issued 06, 2006 A

7
V3300-E2B, V3300-T-E2B, WSM DIMENSIONS
DIMENSIONS
KiSC issued 06, 2006 A

CONTENTS
GENERAL
1. ENGINE IDENTIFICATION............................................................................. G-1
[1] MODEL NAME AND ENGINE SERIAL NUMBER................................ G-1
[2] E2B ENGINE............................................................................................. G-1
[3] CYLINDER NUMBER ............................................................................... G-2
2. GENERAL PRECAUTIONS............................................................................ G-3
3. MAINTENANCE CHECK LIST....................................................................... G-4
4. CHECK AND MAINTENANCE....................................................................... G-6
[1] DAILY CHECK POINTS........................................................................... G-6
[2] CHECK POINTS OF INITIAL 50 HOURS............................................. G-8
[3] CHECK POINT OF EVERY 50 HOURS ............................................... G-9
[4] CHECK POINTS OF EVERY 250 HOURS......................................... G-10
[5] CHECK POINTS OF EVERY 500 HOURS......................................... G-12
[6] CHECK POINT OF EVERY 1000 HOURS ......................................... G-15
[7] CHECK POINTS OF EVERY 1 OR 2 MONTHS............................... G-16
[8] CHECK POINTS OF EVERY 1500 HOURS....................................... G-18
[9] CHECK POINTS OF EVERY 3000 HOURS....................................... G-20
[10]CHECK POINTS OF EVERY 1 YEAR................................................ G-23
[11]CHECK POINTS OF EVERY 2 YEARS.............................................. G-24
5. SPECIAL TOOLS.......................................................................................... G-27
KiSC issued 06, 2006 A

G-1
V3300-E2B, V3300-T-E2B, WSM G GENERAL
1. ENGINE IDENTIFICATION
[1] MODEL NAME AND ENGINE SERIAL NUMBER
When contacting the manufacture, always specify your engine
model name and serial number.
The engine model and its serial number need to be identified
before the engine can be serviced or parts replaced.
■Engine Serial Number
The engine serial number is an identified number for the engine.
It is marked after the engine model number.
It indicates month and year of manufacture as follows.
•Year of manufacture
W1010477
Alphabet or
Number Year Alphabet or
Number Year
1 2001 F 2015
2 2002 G 2016
3 2003 H 2017
4 2004 J 2018
5 2005 K 2019
6 2006 L 2020
7 2007 M 2021
8 2008 N 2022
9 2009 P 2023
A 2010 R 2024
B 2011 S 2025
C 2012 T 2026
D 2013 V 2027
E 2014
(1) Engine Model Name and Serial
Number
KiSC issued 06, 2006 A

G-2
V3300-E2B, V3300-T-E2B, WSM G GENERAL
•Month of manufacture
e.g. V3300-3A0001
“3” indicates 2003 and “A” indicates January.
So, 3A indicates that the engine was manufactured in January,
2003.
W1011076
[2] E2B ENGINE
[ex. Model Name V3300-E2B-XXXX]
The emission controls that have been put into effect in various countries to prevent air pollution will be stepped up.
The time to enforce the regulations differs depending on the engine output classifications.
Kubota has been supplying the diesel engines conforming to the emission regulations in respective countries.
Exhaust emissions regulations shift to the second stage. Kubota executed the improvement of the engine according
to this regulation.
In order to discriminate the engines conforming to Tier 1 / Phase 1 requirements and those conforming to Tier 2 /
Phase 2 requirements, we have adopted E2B as a new model name for the engines conforming Tier 2 / Phase 2
regulations.
In the after-sale services for V3300-E2B and V3300-T-E2B series engines, only use the dedicated parts for E2B
models and carry out the maintenance services accordingly.
[3] CYLINDER NUMBER
The cylinder numbers of kubota diesel engine are designated as
shown in the figure.
The sequence of cylinder numbers is given as No.1, No.2, No.3
and No.4 starting from the gear case side.
W1011077
Month Engine Serial Number
0001 ~ 9999 10000 ~
January A0001 ~ A9999 B0001 ~
February C0001 ~ C9999 D0001 ~
March E0001 ~ E9999 F0001 ~
April G0001 ~ G9999 H0001 ~
May J0001 ~ J9999 K0001 ~
June L0001 ~ L9999 M0001 ~
July N0001 ~ N9999 P0001 ~
August Q0001 ~ Q9999 R0001 ~
September S0001 ~ S9999 T0001 ~
October U0001 ~ U9999 V0001 ~
November W0001 ~ W9999 X0001 ~
December Y0001 ~ Y9999 Z0001 ~
KiSC issued 06, 2006 A

G-3
V3300-E2B, V3300-T-E2B, WSM G GENERAL
2. GENERAL PRECAUTIONS
• During disassembly, carefully arrange removed parts in a clean
area to prevent confusion later. Screws, bolts and nuts should be
replaced in their original position to prevent reassembly errors.
• When special tools are required, use KUBOTA genuine special
tools. Special tools which are not frequently used should be
made according to the drawings provided.
• Before disassembling or servicing live wires, make sure to
always disconnect the grounding cable from the battery first.
• Remove oil and dirt from parts before measuring.
• Use only KUBOTA genuine parts for parts replacement to
maintain engine performance and to ensure safety.
• Gaskets and O-rings must be replaced during reassembly.
Apply grease to new O-rings or oil seals before assembling.
• When reassembling external or internal snap rings, position them
so that the sharp edge faces against the direction from which
force is applied.
• Be sure to perform run-in the serviced or reassembled engine.
Do not attempt to give heavy load at once, or serious damage
may result to the engine.
W1011734
(1) Grease
(2) Force
(3) Place the Sharp Edge against the
Direction of Force
(A) External Snap Ring
(B) Internal Snap Ring
KiSC issued 06, 2006 A

G-4
V3300-E2B, V3300-T-E2B, WSM G GENERAL
3. MAINTENANCE CHECK LIST
To maintain long-lasting and safe engine performance, make it a rule to carry out regular inspections by following
the table below.
* The items listed above (* marked) are registered as emission related critical parts by KUBOTA in the U.S.EPA
nonroad emission regulation.
As the engine owner, you are responsible for the performance of the required maintenance on the engine according
to the above instruction. W1029462
Item
Service Interval
Initial
50 hrs Every 50 hrs Every
250
hrs
Every
500
hrs
Every
1000
hrs
Every 1
or 2
months
Every
1500
hrs
Every
3000
hrs Every
1 year Every
2
years
Changing engine oil ✩✩ ✩
Replacing oil filter cartridge ✩✩
*Checking fuel hoses and clamps ✩
*Cleaning air filter element
(Replace the element after 6 times cleanings) ✩
*Cleaning fuel filter ✩
Checking battery electrolyte level ✩
Checking radiator hoses and clamps ✩
*Checking intake air line ✩
Checking fan belt tension and damage ✩✩
*Replacing fuel filter cartridge ✩
Replacing fan belt ✩✩
Cleaning radiator interior ✩
Checking valve clearance ✩
Recharging battery ✩
*Checking injection nozzle condition ✩
*Checking turbocharger ✩
Checking fuel injection pump ✩
*Checking injection timing (spill timing) ✩
*Replacing air filter element ✩
Changing radiator coolant (L.L.C.) ✩
Replacing radiator hoses and clamps ✩
*Replacing fuel hoses and clamps ✩
*Replacing intake air line ✩
Replacing battery ✩
KiSC issued 06, 2006 A

G-5
V3300-E2B, V3300-T-E2B, WSM G GENERAL
CAUTION
• When changing or inspecting, be sure to level and stop the engine.
■NOTE
Lubricating Oil
With the emission control now in effect, the CF-4 and CG-4 lubricating oils have been developed for use of a low-
sulfur fuel on-road vehicle engines. When an off-road vehicle engine runs on a high-sulfur fuel, it is advisable to
employ the CF, CD or CE lubricating oil with a high total base number. If the CF-4 or CG-4 lubricating oil is used with
a high-sulfur fuel, change the lubricating oil at shorter intervals.
•Lubricating oil recommended when a low-sulfur or high-sulfur fuel is employed.
❍: Recommendable X : Not recommendable W1035555
Fuel
Lubricating
oil class
Low sulfur
(0.5 % ≥)High sulfur Remarks
CF ❍❍TBN ≥10
CF-4 ❍X
CG-4 ❍X
KiSC issued 06, 2006 A

G-6
V3300-E2B, V3300-T-E2B, WSM G GENERAL
4. CHECK AND MAINTENANCE
[1] DAILY CHECK POINTS
Checking Engine Oil Level
1. Level the engine.
2. To check the oil level, draw out the dipstick (1), wipe it clean,
reinsert it, and draw it out again.
Check to see that the oil level lies between the two notches.
3. If the level is too low, add new oil to the specified level.
IMPORTANT■
• When using an oil of different maker or viscosity from the
previous one, drain old oil. Never mix two different types of
oil.
NOTE■
• Be sure to inspect the engine, locating it on a horizontal
place. If placed on gradients, accurately, oil quantity may
not be measured.
• Be sure to keep the oil level between upper and lower limits
of the dipstick. Too much oil may cause a drop in output or
excessive blow-by gas. On the closed breather type engine
in which mist is sucked through port, too much oil may
caused oil hammer. While too little oil, may seize the
engine’s rotating and sliding parts.
W1035676
(1) Dipstick (a) Maximum
(b) Minimum
KiSC issued 06, 2006 A

G-7
V3300-E2B, V3300-T-E2B, WSM G GENERAL
Checking and Replenish Coolant
1. Without recovery tank :
Remove the radiator cap (1) and check to see that the coolant
level is just below the port.
With recovery tank (2) :
Check to see that the coolant level lies between FULL (A) and
LOW (B).
2. If coolant level is too low, check the reason for decreasing
coolant.
(Case 1)
If coolant is decreasing by evaporation, replenish only fresh, soft
water.
(Case 2)
If coolant is decreasing by leak, replenish coolant of the same
manufacture and type in the specified mixture ratio (fresh, soft
water and L.L.C.). If the coolant brand cannot be identified, drain
out all of the remaining coolant and refill with a totally new brand
of coolant mix.
CAUTION
• Do not remove the radiator cap until coolant temperature is
below its boiling point. Then loosen the cap slightly to
relieve any excess pressure before removing the cap
completely.
IMPORTANT
■
• During filling the coolant, air must be vented from the engine
coolant passages. The air vents by jiggling the radiator
upper and lower hoses.
• Be sure to close the radiator cap securely. If the cap is loose
or improperly closed, coolant may leak out and the engine
could overheat.
• Do not use an antifreeze and scale inhibitor at the same time.
• Never mix the different type or brand of L.L.C..
W1035779
(1) Radiator Cap
(2) Recovery Tank A: FULL B: LOW
KiSC issued 06, 2006 A

G-8
V3300-E2B, V3300-T-E2B, WSM G GENERAL
[2] CHECK POINTS OF INITIAL 50 HOURS
Changing Engine Oil
CAUTION
• Be sure to stop engine before changing engine oil.
1. Start and warm up the engine for approx. 5 minutes.
2. Place an oil pan underneath the engine.
3. To drain the used oil, remove the drain plug (1) at the bottom of
the engine and drain the oil completely.
4. Screw the drain plug (1).
5. Fill new oil up to upper line on the dipstick (2).
IMPORTANT
■
• When using an oil of different maker or viscosity from the
previous one, remove all of the old oil.
• Never mix two different types of oil.
• Engine oil should have properties of API classification CD/
CE/CF/CF-4/CG-4.
• Use the proper SAE Engine Oil according to ambient
temperature.
W1016604
Replacing Oil Filter Cartridge
CAUTION
• Be sure to stop the engine before changing filter cartridge.
1. Remove the oil filter cartridge (1) with the filter wrench.
2. Apply a slight coat of oil onto the new cartridge gasket.
3. To install the new cartridge, screw it in by hand. Over tightening
may cause deformation of rubber gasket.
4. After the new cartridge has been replaced, the engine oil
normally decrease a little. Thus see that the engine oil does not
leak through the seal and be sure to read the oil level on the
dipstick. Then, replenish the engine oil up to the specified level.
IMPORTANT■
• To prevent serious damage to the engine, replacement
element must be highly efficient. Use only a KUBOTA
genuine filter or its equivalent.
W1017137
Above 25 °C (77 °F) SAE 30 or SAE 10W-30
SAE 10W-40
0 °C to 25 °C (32 °F to 77 °F) SAE 20 or SAE 10W-30
SAE 10W-40
Below 0 °C (32 °F) SAE 10W or SAE 10W-30
SAE 10W-40
Engine oil capacity 13.2 L
3.49 U.S.gals
(1) Drain Plug (2) Dipstick
(1) Engine Oil Filter Cartridge
KiSC issued 06, 2006 A

G-9
V3300-E2B, V3300-T-E2B, WSM G GENERAL
Fan Belt Tension
1. Measure the deflection (A), depressing the belt halfway between
the fan drive pulley and alternator pulley at specified force 98 N
(10 kgf, 22 lbs).
2. If the measurement is not within the factory specifications, loosen
the alternator mounting screws and relocate the alternator to
adjust.
W1208957
[3] CHECK POINT OF EVERY 50 HOURS
Checking Fuel Hose and Clamp Bands
1. If the clamp (2) is loose, apply oil to the threads and securely
retighten it.
2. The fuel hose (3) is made of rubber and ages regardless of the
period service.
Change the fuel pipe together with the clamp every two years.
3. However, if the fuel hose and clamps are found to be damaged
or deteriorate earlier than two years, then change or remedy.
4. After the fuel hose and the clamps have been changed, bleed the
fuel system.
CAUTION
• Stop the engine when attempting the check and change
prescribed above.
(When bleeding fuel system)
1. Fill the tank with fuel and open the cock.
2. Loosen the air vent coupling bolt of fuel filter a few turns.
3. When there is no more air bubbles in the fuel coming out of this
coupling bolt, tighten the coupling bolt.
4. Open the air vent cock (1) on the top of fuel injection pump.
5. If equipped electrical fuel feed pump, turn the key on AC position
and pump the fuel up for 10 to 15 seconds.
If equipped mechanical fuel feed pump, set the stop lever on stop
position and crank the engine for 10 to 15 seconds.
6. Close securely the air vent cock (1) after air bleeding.
IMPORTANT■
• Except when venting the air, be sure to keep closed the air
vent coupling bolt of the fuel injection pump. Otherwise, the
engine may stall.
W1035921
Deflection (A) Factory spec. 10 to 12 mm
0.394 to 0.472 in.
(A) Deflection
(1) Air Vent Cock
(2) Clamp (3) Fuel Hose
KiSC issued 06, 2006 A

G-10
V3300-E2B, V3300-T-E2B, WSM G GENERAL
[4] CHECK POINTS OF EVERY 250 HOURS
Fan Belt Tension
1. Measure the deflection (A), depressing the belt halfway between
the fan drive pulley and alternator pulley at specified force 98 N
(10 kgf, 22 lbs).
2. If the measurement is not within the factory specifications, loosen
the alternator mounting screws and relocate the alternator to
adjust.
W1014131
Fan Belt Damage and Wear
1. Check the fan belt for damage.
2. If the fan belt is damaged, replace it.
3. Check if the fan belt is worn and sunk in the pulley groove.
4. If the fan belt is nearly worn out and deeply sunk in the pulley
groove, replace it.
W1209480
Cleaning Air Cleaner Element
1. Remove the air cleaner element.
2. Use clean dry compressed air on the inside of the element.
Pressure of compressed air must be under 205 kPa (2.1 kgf/cm2,
30 psi).
Maintain reasonable distance between the nozzle and the filter.
NOTE■
• The air cleaner uses a dry element. Never apply oil to it.
• Do not run the engine with filter element removed.
• Change the element once a year or every 6th cleaning.
W1045746
Deflection (A) Factory spec. 10 to 12 mm
0.394 to 0.472 in.
(A) Deflection
(A) Good (B) Bad
KiSC issued 06, 2006 A