Kubota L3560 User manual

English (U.S.A.)
Code No. TD350-7956-2
L5460·L6060
L3560·L4060·L4760MODELS
OPERATOR'S MANUAL
L
3
5
6
0
·
L
4
0
6
0
·
L
4
7
6
0
·
L
5
4
6
0
·
L
6
0
6
0
© KUBOTA Corporation 2012
PRINTED IN JAPAN
READ AND SAVE THIS MANUAL

KUBOTA Corporation is ···
Since its inception in 1890, KUBOTA Corporation has grown to
rank as one of the major firms in Japan.
To achieve this status, the company has through the years
diversified the range of its products and services to a remarkable
extent, until today, 19 plants and 16,000 employees produce over
1,000 different items, large and small.
All these products and all the services which accompany them,
however, are unified by one central commitment.
KUBOTA makes products which, taken on a national scale, are
basic necessities. Products which are indispensable, products
intended to help individuals and nations fulfill the potential inherent
in their environment. For KUBOTA is the Basic Necessities Giant.
This potential includes water supply, food from the soil and from
the sea, industrial development, architecture and construction,
transportation.
Thousands of people depend on KUBOTA's know-how, technology,
experience and customer service. You too can depend on
KUBOTA.
L3560·L4060·L4760
L5460·L6060
AT . F . 5 - 8 . 12 . AK
Abbreviations Definitions
ABBREVIATION LIST
2 Wheel Drive
4 Wheel Drive
American Petroleum Institute
American Society of Agricultural and Biological Engineers, USA
American Society for Testing and Materials, USA
Deutsches Institut für Normung, GERMANY
Dual Traction [4WD]
Feet Per Minute
Glide Shift Transmission
High Speed-Low Speed
Hydrostatic Transmission
Meters Per Second
Power Take Off
Right-hand and left-hand sides are determined by facing
in the direction of forward travel
Roll-Over Protective Structures
Revolutions Per Minute
Revolutions Per Second
Society of Automotive Engineers, USA
Slow Moving Vehicle
2WD
4WD
API
ASABE
ASTM
DIN
DT
fpm
GST
Hi-Lo
HST
m/s
PTO
RH/LH
ROPS
rpm
r/s
SAE
SMV
California Proposition 65
WARNING
Engine exhaust, some of its constituents,
certain vehicle components and fluids,
contain or emit chemicals known to the
State of California to cause cancer and birth
defects or other reproductive harm.

FOREWORD
3
SAFETY FIRST
IMPORTANT :
NOTE :
3DANGER :
3WARNING :
3CAUTION :
Indicates an imminently hazardous situation which, if not
avoided, will result in death or serious injury.
Indicates a potentially hazardous situation which, if not
avoided, could result in death or serious injury.
Indicates a potentially hazardous situation which, if not
avoided, could result in minor or moderate injury.
Indicates that equipment or property damage could result if
instructions are not followed.
Gives helpful information.
Thank you very much for choosing the L series tractor with CAB.
This operator's manual covers the operation, inspection and preventive
maintenance instructions that are specific to the L series CAB models. For other
information and instructions, refer to the separately issued operator's manual for
their sister models.
Please read this manual carefully along with the tractor operator's manual, to
operate the machine properly and safely.
Proper daily inspection, servicing and lubrication keeps your machine in good
condition.
This symbol, the industry's ''Safety Alert Symbol'', is used throughout this manual
and on labels on the machine itself to warn of the possibility of personal injury.
Read these instructions carefully. It is essential that you read the instructions and
safety regulations before you attempt to assemble or use this unit.

CONTENTS
SAFE OPERATION ............................................................................................ -1
SPECIFICATIONS....................................................................................................... 1
SPECIFICATION TABLE ......................................................................................... 1
CAB OPERATION ....................................................................................................... 3
DOOR AND WINDOW ............................................................................................. 3
Locking and Unlocking the Door.......................................................................................3
Opening the Door ............................................................................................................. 3
Rear Window ....................................................................................................................3
Side Window.....................................................................................................................4
Emergency Exit.................................................................................................................4
DOME LIGHT........................................................................................................... 4
Dome Light ....................................................................................................................... 4
WORK LIGHT .......................................................................................................... 4
Work Light Switch.............................................................................................................4
Front Work Light ...............................................................................................................4
Rear Work Light (if equipped)...........................................................................................5
WIPER ..................................................................................................................... 5
Front Wiper / Washer Switch............................................................................................5
Rear Wiper / Washer Switch (if equipped)........................................................................5
Using the Wipers in Cold Season.....................................................................................5
AIR CONDITIONER ................................................................................................. 5
Airflow ............................................................................................................................... 5
Air Control Vent ................................................................................................................6
Control Panel.................................................................................................................... 7
Operation .......................................................................................................................... 8
REAR / SIDE DEFOGGER WITH TIMER (if equipped)......................................... 10
ELECTRICAL OUTLET.......................................................................................... 10
Electrical Outlet...............................................................................................................10
MAINTENANCE......................................................................................................... 11
SERVICE INTERVALS .......................................................................................... 11
PERIODIC SERVICE................................................................................................. 12
DAILY CHECK ....................................................................................................... 12
Cleaning Air Conditioner Condenser Screen.................................................................. 12
EVERY 200 HOURS .............................................................................................. 12
Cleaning Inner Air Filter..................................................................................................12
Cleaning Fresh Air Filter.................................................................................................12
Checking Air Conditioner Condenser .............................................................................13
Adjusting Air-Conditioner Belt Tension...........................................................................13
EVERY 1 YEAR ..................................................................................................... 13
Checking Air-Conditioner Pipe and Hose .......................................................................13
Checking CAB Isolation Cushion....................................................................................13
EVERY 4 YEARS................................................................................................... 13
Replacing Air Conditioner Hose......................................................................................13
SERVICE AS REQUIRED...................................................................................... 14
Lubricating Points ........................................................................................................... 14

CONTENTS
Adding Washer Liquid..................................................................................................... 14
Checking the Amount of Refrigerant (gas) .....................................................................14
APPENDICES............................................................................................................ 15
INDEX .................................................................................................................... 15

-1SAFE OPERATION
SAFE OPERATION
Careful operation is your best insurance against an accident.
Read and understand carefully this section of the separately issued operator's manual before operating the
tractor.
BDANGER, WARNING AND CAUTION LABELS

SAFE OPERATION-2
BCARE OF DANGER, WARNING AND CAUTION LABELS
1. Keep danger, warning and caution labels clean and free from obstructing material.
2. Clean danger, warning and caution labels with soap and water, dry with a soft cloth.
3. Replace damaged or missing danger, warning and caution labels with new labels from your local KUBOTA Dealer.
4. If a component with danger, warning and caution label (s) affixed is replaced with new part, make sure new label (s) is
(are) attached in the same location (s) as the replaced component.
5. Mount new danger, warning and caution labels by applying on a clean dry surface and pressing any bubbles to outside
edge.

1SPECIFICATIONS
SPECIFICATIONS
SPECIFICATION TABLE
Model
L3560 L4060 L4760 L5460 L6060
4WD
Engine
Model D1803-CR-E4 V2403-CR-E4 V2403-CR-TE4
Type Direct injection vertical, water-cooled, 4-cycle diesel
Number of cylinders 3 4
Total displacement L (cu. in.) 1.826 (111.4) 2.434 (148.5)
Bore and stroke mm (in.) 87 x 102.4 (3.4 x 4.0)
Rated revolution rpm 2600
Low idling revolution rpm 800
Net power* kW (HP) 26.1 (35.0) 29.8 (40.0) 35.1 (47.0) 40.3 (54.0) 44.8 (60.0)
PTO power*
(factory observed)
kW (HP)/
rpm
20.9 (28.0)/
2600
24.2 (32.5)/
2600
29.5 (39.5)/
2600
34.7 (46.5)/
2600
39.5 (53.0)/
2600
Maximum torque N-m
(ft-lbs.) 114.1 (84.2) 133.5 (98.5) 157.4 (116.1) 182.6 (134.7) 195.6 (144.3)
Battery capacity 12V, RC: 133 min, CCA: 582A
Capacities
Fuel tank L
(U.S.gals.) 51 (13.5)
Engine crankcase
(with filter)
L
(U.S.qts.) 6.7 (7.1) 8.2 (8.7) 9.4 (9.9)
Engine coolant L
(U.S.qts.) 7.5 (7.9) 8.2 (8.7)
Transmission case L
(U.S.gals.) 42 (11.1) 43 (11.4) 45 (11.9)
Dimensions
Overall length
(without 3p) mm (in.) 2920 (115.0) 3085 (121.5) 3210 (126.4)
Overall width
(min. tread) mm (in.) 1520 (59.8) 1690 (66.5) 1710 (67.3)
Overall height mm (in.) 2300 (90.6) 2315 (91.1) 2350 (92.5)
Wheel base mm (in.) 1805 (71.1) 1895 (74.6) 1915 (75.4)
Min. ground clearance mm (in.) 342 (13.5) 360 (14.2) 392 (15.4)
Tread
Front mm (in.) 1155 (45.5) 1300 (51.2) 1340 (52.8)
Rear mm (in.)
1200 (47.2)
1300 (51.2)
1385 (54.5)
1480 (58.3)
1285 (50.6)
1435 (56.5)
1530 (60.2)
1325 (52.2)
1430 (56.3)
Weight (with CAB) kg (lbs.) 1760 (3880) 1875 (4134) 1915 (4222) 1980 (4365)

2 SPECIFICATIONS
NOTE : *Manufacturer's estimate
The company reserve the right to change the specifications without notice.
Traveling
system
Standard
tire size
Front 7-16 8.3-16 9.5-16
Rear 12.4-24 14.9-24 14.9-26
Clutch ---
Steering Hydrostatic power steering
Transmission Hydrostatic transmission (3 speeds)
Braking system Wet disk type
Min. turning radius
(with brake) m (feet) 2.7 (8.9) 2.8 (9.2)
Hydraulic
unit
Hydraulic control system Position control
Pump capacity
L
(U.S.gals)/
min.
30.4 (8.0) 35.6 (9.4)
3-point hitch SAE category 1 SAE category 1, 2
Max. lift
force
At lift
points kg (lbs.) 1700 (3750) 1750 (3860)
24 in.
behind
lift
points
kg (lbs.) 1200 (2650) 1250 (2760) 1350 (2980)
System pressure MPa
(kgf/cm ) 17.7 (180)
PTO
Rear PTO
SAE 1-3/8, 6 splines
PTO/
Engine
speed
rpm 540/2426 540/2476 540/2403
MID-PTO
(if equipped)
USA No.5 (KUBOTA 10-tooth) involute spline
PTO/
Engine
speed
rpm 2000/2451 2000/2502 2000/2429
Model
L3560 L4060 L4760 L5460 L6060
4WD

3CAB OPERATION
CAB OPERATION
DOOR AND WINDOW
BLocking and Unlocking the Door
BOpening the Door
BRear Window
Turn the rear window handle clockwise to the vertical
position and push the handle. The rear window is opened
by the gas spring cylinder.
From the outside ...... Insert the key into the door lock.
Turn the key clockwise to unlock
the door. To lock the door, turn
the key in the opposite direction.
The key can be removed when it
is in the vertical direction.
From the inside ....... Push down the lock knob to lock
the door.
Pull up the lock knob to unlock
the door.
From the outside ...... Unlock the door, and pull the
outer door handle.
(1) Outer door handle
(2) Door lock
(A) "PULL"
From the inside ........ Unlock the door and pull the
inner door handle.
(1) Inner door handle
(2) Lock knob
(A) "PULL"
(B) "PUSH" (Lock)
(C) "PULL" (Unlock)
(1) Rear window handle (A) "OPEN"
(B) "CLOSE"

CAB OPERATION4
BSide Window
Pull the side window handle and push the side window to
open the window.
BEmergency Exit
1. Open the right door of the cab if the left door is
blocked, and vice versa in an emergency situation.
2. Exit through rear window if CAB doors are blocked in
an emergency situation.
DOME LIGHT
BDome Light
Sliding the dome light switch will give the following light
condition:
WORK LIGHT
BWork Light Switch
Turn on the key switch and press the top half of the work
light switch. The work light and the switch's indicator light
up. Press the bottom half of the work light switch to turn
off the light and indicator.
BFront Work Light
(1) Side window handle
OFF ............... The light does not turn on when the
door is opened.
ON ................ The light remains on regardless of the
door position.
(1) Dome light
(2) Dome light switch
(A) "OFF"
(B) "ON"
(1) Front work light switch
(2) Rear work light switch
(if equipped)
(A) Indicator for work lights
(1) Front work light

5CAB OPERATION
BRear Work Light (if equipped)
WIPER
BFront Wiper / Washer Switch
1. Turn on the key switch and press the top half of the
wiper switch to the first step, and the wiper is activated.
When the switch is pressed further to the second step,
washer liquid jets out.
The jetting continues while the switch is pressed and
the wiper is activated continuously.
2. Press the bottom half of the wiper / washer switch,
washer liquid only jets out.
BRear Wiper / Washer Switch (if equipped)
See "Front wiper / Washer switch" section, for instructions
to use this switch.
ADo not activate the wipers when the windows are dry,
they may be scratched.
Be sure to jet washer liquid first and then activate the
wipers.
BUsing the Wipers in Cold Season
1. While not used in cold season, keep the wiper blades
off the windshield to prevent them from being stuck
with ice.
2. If the windshield is covered with snow, scrape it off the
windshield before using the wipers.
3. If the wiper blades are stuck on the windshield with ice
and fail to move, be sure to turn the main key switch to
"OFF" and remove the ice off the blades. Then place
the main key switch back to "ON".
4. When commercially available cold-season wiper
blades are used, make sure their size is the same as
or smaller than that of the standard ones.
AIn cold season, the wiper blades and the wiper motor
might get overloaded causing damage. To avoid this,
be sure to take the above precautions.
AIR CONDITIONER
BAirflow
Air in the CAB and fresh air introduced into the CAB flow
as shown below. Adjust the eight air ports to obtain the
desired condition.
(1) Rear work light
(1) Front wiper / washer switch
(2) Rear wiper / washer switch
(1) Control panel
(2) Side air outlet (face area)
(3) Front air outlet
(4) Door air outlet
(A) Inner air recirculation

CAB OPERATION6
BAir Control Vent
CFront air outlet
The front air outlets can be independently adjusted as
required. To defrost the windshield, rotate the outlets
toward the windshield.
CSide air outlet and door air outlet
The side and door air outlets can be adjusted to direct air
on to the operator, door window or the rear of the CAB.
AIf the airflow rate at the face is too low, close the door
air outlet.
To avoid personal injury;
AReplace the water hoses every 2 years.
ADaily inspection
Have the tractor repaired immediately if any of
the following defects are discovered.
(Such defects may cause burns or injury. They
may also cause engine seizure or other serious
failure.)
AScratches, cracks or swelling in water
hoses.
AWater leakage at water hose joints.
AMissing or damaged water hose protective
wrap or grommets.
ALoose mounting bolts, damaged brackets.
ADo not touch the water hoses and the heater
with your hand. You may get burned.
AIf the window fails to defrost in extreme
conditions or becomes cloudy when
dehumidifying the CAB, wipe off moisture with
a soft cloth.
ADo not block all the air outlets of the air
conditioner. A problem could occur.
(A) Fresh air inlet
(1) Front air outlet (A) "OPEN"
(B) "CLOSED"
(C) "WINDSHIELD"
(1) Side air outlet
(2) Door air outlet

7CAB OPERATION
BControl Panel
CTemperature Control Dial
Set this dial at the desired position to obtain the optimum
air temperature. Turn the dial in the "WARM" direction to
obtain warmer air. Turn it in the "COOL" direction to obtain
cooler air.
CBlower Switch
Air volume can be changed in 4 steps. At the "4" position,
the largest air volume is obtained.
CAir Conditioner Switch
Push this switch to activate the air conditioner. An
indicator light will light up when the switch is set to "ON".
Push the switch again to turn the air conditioner off, in
which case the indicator light will be off.
AWith the blower switch at the "OFF" position, the
indicator light will not light up even when the air
conditioner switch is set to "ON".
ATo operate the air conditioner after the tractor has not
been used for one week or longer, run the engine at
idling speed first and then set the air conditioner switch
to "ON". Keep this for one minute or so.
If the air conditioner switch is set to "ON" with the
engine running at high rpm, the compressor may get in
trouble.
CRecirculation / fresh air selection switch
Each time the switch is pressed, the air flow position
changes for "RECIRCULATION" or "FRESH AIR". An
indicator light will light up when the switch is set to
"RECIRCULATION". And the indicator light will be off
when the switch is set to "FRESH AIR".
AWhen heating, do not keep the switch at the
"RECIRCULATION" position for a long time. The
windshield easily gets foggy.
AWhile working in a dusty conditions, keep the switch at
the "FRESH AIR" position. This increases the
pressure in the CAB, which helps prevent dust from
coming into the CAB.
(1) Temperature control dial
(2) Recirculation / fresh air selection switch
with indicator light
(3) Air conditioner switch with indicator light
(4) Blower switch
(A) "WARM"
(B) "COOL"
FRESH AIR:
(Indicator: OFF)
Fresh air will flow into the CAB.
This is helpful when you work in
dusty conditions or if the glass
windows get foggy.
RECIRCULATION:
(Indicator: ON)
In-CAB air will be recirculated.
This is useful for cooling or heating
the CAB quickly or keeping it extra
cool or warm.
(1) Recirculation / fresh air
selection switch with
indicator light
(A) "RECIRCULATION"
(B) "FRESH AIR"

CAB OPERATION8
BOperation
CHeating
1. Set the recirculation / fresh air selection switch to the
"FRESH AIR" position. To raise the temperature in the
CAB quickly, set this switch to the "RECIRCULATION"
position.
2. Adjust the blower switch and the temperature control
dial to achieve a comfortable temperature level.
CCooling or dehumidifying-heating
1. Set the recirculation / fresh air selection switch to the
"FRESH AIR" position. To lower the temperature in the
CAB quickly, set this switch to the "RECIRCULATION"
position.
2. Press and turn on the air-conditioner switch with
indicator.
3. Turn on the blower switch.
4. Adjust the temperature control dial to the "COOL" or
an intermediate position to achieve a comfortable
temperature level.
AIn summer when the heater is not used, keep the
temperature control dial at the max "COOL" (end of
counterclockwise) position. Otherwise, hot air will
raise the temperature in the CAB.
(1) Temperature control dial
(2) Recirculation / fresh air selection switch with indicator light
(3) Blower switch
(1) Temperature control dial
(2) Recirculation / fresh air selection switch
with indicator light
(3) Air conditioner switch with indicator light
(4) Blower switch
(A) "WARM"
(B) "COOL"

9CAB OPERATION
CFoot warming and head cooling
1. In the cooling or dehumidifying-heating mode, set the
temperature control dial at the center position area.
2. Open the front air outlet and the door air outlet direct it
to your feet. Close the side air outlet.
3. You can feel your head cool and your feet warm.
CDefrosting or demisting
To defrost or demist the windshield, take the following
steps.
1. Open the front air outlet and the door air outlet direct it
to the windshield. Close the side air outlet.
2. Set the recirculation / fresh air selection switch to the
"FRESH AIR" position.
3. Set the blower switch and the temperature control dial
to the "4" and max "WARM" (end of clockwise)
positions, respectively.
(1) Temperature control dial (A) Center position area
(A) "OPEN"
(B) "CLOSED"
(1) Temperature control dial
(2) Recirculation / fresh air selection switch
with indicator light
(A) "WARM"
(A) "OPEN"
(B) "CLOSED"

CAB OPERATION10
REAR / SIDE DEFOGGER WITH TIMER (if
equipped)
To activate the rear / side window defoggers, press the
switch marked while the key switch is in the "ON"
position. Then, the yellow light on the switch turns on.
After about 15 minutes, the defoggers automatically turn
off as well as the yellow light. To turn the defogger off,
press the switch once more.
AThe battery will discharge if the defogger and the key
switch remain in the "ON" or "ACC" positions with the
engine stopped.
Always use the defogger with the engine running.
ELECTRICAL OUTLET
BElectrical Outlet
A electrical outlet is supplied for use with implement.
(1) Defogger switch
(2) Yellow light
(1) Accessory electrical outlet (Total 20 A)

11MAINTENANCE
MAINTENANCE
SERVICE INTERVALS
(Only the Check Points for Tractors with CAB)
No. Items Daily
Indication on hour meter
Interval Ref.
page
100 200 300 400 500 600 700 800
1Clogging of air conditioner condenser
screen Clean 12
2 Tension of air conditioner drive belt Adjust every 200 Hr 13
3 Clogging of inner air filter Clean every 200 Hr 12
4 Clogging of fresh air filter Clean every 200 Hr 12
5 Clogging of air conditioner condenser Check every 200 Hr 13
6 Air conditioner pipes and hoses
Check every 1 year 13
Replace every 4 years 13
7 CAB isolation cushion Check every 1 year 13
8 Washer liquid Check service as required 14
9 Amount of refrigerant (gas) Check service as required 14

12 PERIODIC SERVICE
PERIODIC SERVICE
DAILY CHECK
BCleaning Air Conditioner Condenser
Screen
To avoid personal injury or death:
ABe sure to stop the engine before removing the
screen.
AThe condenser and receiver become hot while
the air conditioner is running. Before checking
or cleaning them, wait enough until they cool
down.
1. Detach the air conditioner condenser screen and
remove all foreign materials.
AGrill and screen must be clean from debris to prevent
engine from overheating and to allow good air intake
for air cleaner.
EVERY 200 HOURS
BCleaning Inner Air Filter
Press the inner air filter in the arrow-marked directions to
unlock it and remove the inner filter, and blow air from the
direction opposite to the filter's normal air flow.
Pressure of compressed air must be under 205 kPa (2.1
kgf/cm , 30 psi).
BCleaning Fresh Air Filter
Remove the knob bolts and pull out filter.
AAttach the filter and cover as the illustration above.
(1) Air conditioner condenser screen
(1) Inner air filter (A) "PUSH"
(1) Fresh air filter
(2) Cover
(3) Knob bolt
(A) Air inlet port

13PERIODIC SERVICE
CCleaning the air filter
ANormal use
Blow air from the opposite direction to the filter's
normal air flow.
Pressure of compressed air must be under 205 kPa
(2.1 kgf/cm , 30 psi).
ADo not hit the filter. If the filter becomes deformed, dust
may enter into the air-conditioner, which may cause
damage and malfunction.
AIf the filter is very dirty:
Dip the filter in lukewarm water with mild dish washing
detergent.
Move it up and down as well as left and right to loosen
dirt. Rinse the filter with clean water and let it air-dry.
ADo not use gasoline, thinner or similar chemicals to
clean the filter as damage to the filter may occur.
AIt may also cause an unpleasant odor in the CAB when
the system is used next.
BChecking Air Conditioner Condenser
Check air conditioner condenser to be sure it is clean of
debris.
BAdjusting Air-Conditioner Belt Tension
To avoid personal injury or death:
ABe sure to stop the engine before checking belt
tension.
1. Stop the engine and remove the key.
2. Apply moderate thumb pressure to belt between
pulleys.
3. If tension is incorrect, loosen the tension pulley
mounting nut and turn the adjusting bolt to adjust the
belt tension within acceptable limits.
4. Replace air-conditioner belt if it is damaged.
EVERY 1 YEAR
BChecking Air-Conditioner Pipe and Hose
1. Check to see that all lines and hose clamps are tight
and not damaged.
2. If hoses and clamps are found worn or damaged,
consult your local KUBOTA Dealer for this service.
BChecking CAB Isolation Cushion
Check the cushion for any breakage or fatigue. Replace
them if they are deteriorated.
EVERY 4 YEARS
BReplacing Air Conditioner Hose
Consult your local KUBOTA Dealer for this service.
(A) "AIR CONDITIONER AIRFLOW"
(1) Air conditioner condenser
Proper air-
conditioner
belt tension
A deflection of between 10 to 12 mm
(0.4 to 0.48 in.) when the belt is pressed
(98 N [10 kgf, 22.1 lbs.]) in the middle of
the span.
(1) Adjusting bolt
(2) Tension pulley mounting nut
(A) Check the belt tension