Kuppersberg FS 603 Installation and maintenance instructions

TECHNICAL PASSPORT
ПАСПОРТ ТЕХНИЧЕСКОГО ИЗДЕЛИЯ
BUILT - IN COOKER
ВСТРАИВАЕМАЯ ВАРОЧНАЯ ПАНЕЛЬ
FS 603, FS 601, FS 63, FG 63

2
TECHNICAL PASSPORT ENGLISH
Gas hob
SECTION 1.
TECHNICALCHARACTERISTICS OF YOUR COOKER...................4
SECTION 2.
INSTALLATION PREPARATIONS OF THE BUILT
-IN COOKER...6
SECTION 3.
THINGS TO BE CONDERED PRIOR TO USE OF YOUR COOKER
AND SAFETY WARNINGS..............................................................9
SECTION 4.
IDENTIFICATION OF THE CONTROL PANEL AND USE OF THE
BURNERS......................................................................................10
SECTION 5.
MAINTENANCE AND CLEANING.................................................11
SECTION 6.
NITIAL PREPARATION AND INSTALLATION OF YOUR TABLE
TOP COOKER.................................................................................12
SECTION 7.
INFORMATION ABOUT THE TRANSPORTATION.......................22

3
ENGLISH TECHNICAL PASSPORT
Gas hob
DEAR CUSTOMER!
«Our aim is to ensure you take most
advantage of your cooker, which is
manufactured in the modem fa-
cilities and passed quality control tests
meticulously.
We, therefore, request you to care-
fully read this manual thoroughly be-
fore use of the cooker an keep it as a
reference».
CUSTOMER SERVICES
Customer Services
Please call the customer services at
the following telephone number for any
failure which you cannot remove.
The customer service will require
you to give the model and serial number
of your equipment. You may nd both
of them in the operating manual and
nameplate.
Dear Customer!
We put into your service our free
toll consumer hotline as a token of
importance we give our valuable
customers. By use of this comprehensive
service, you may get information about
the following subjects and leave
message:
You may get assistance from the
following telephone number to have
access to the telephone numbers of
the Authorized Dealer or Authorized
Service nearest to you and have for
the problems you yourself cannot nd
proper solution.

4
TECHNICAL PASSPORT ENGLISH
Gas hob
SECTION 1.
TECHNICAL CHARACTERISTICS
OF THE TABLE TOP COOKER
Liqueed petroleum gas or naturel
gas fueled built-in cooker, 4+1 -
burner (optional)
1. Cooker grate
2. Spark igniter
3. Normal burner
4. Strong burner (or WOK *)
5. Ancillary burner
6. Gas burning control buttons
7. Cooker upper tray
8. Cooker lower tray
9. Burner lid
*for models with WOK
6
31
4
5
9
2
87

5
ENGLISH TECHNICAL PASSPORT
Gas hob
Model Gas type &
pressure
Heat input and orice size marked (mm)
Surface Auxiliary Semi-rapid Rapid WOK burne
FS 603 G20, G30 enamel 1 kW 2 kW 3,8 kW
FS 601 G20, G30 enamel 1 kW 2 kW 2,9 kW
FG 63 G20, G30 glass 1 kW 2 kW 3,8 kW
FS 63 X G20, G30 glass 1 kW 2 kW 3,8 kW

6
TECHNICAL PASSPORT ENGLISH
Gas hob
SECTION 2.
INSTALLATION PREPARATIONS OF THE BUILT
-IN COOKER
INSTALLATION OF THE COOKER
The cooker has a seal to prevent the liquids from owing from the gaps into
the cabinet. For xing this seal, attach it as shown in the gures ahove. Turn upside
down the cooker and remove the protective band of the rubber seal; both ends of
it should meet perfectly. Install the installation sheets by help of screw as shown
in the gure 5.
And then place the cooker into the clearance of the worktop.
Figure 1
Figure 1
Figure 4
Figure 4
Figure 5
Figure 5
Figure 6
Figure 6
Figure 2
Figure 2
Figure 3
Figure 3
Worktop
Cooker
installation sheet
Fixing points for the installation sheet
screw
Put your cooker upside down in the
styrofoam taken from the package and
apply the silicone.
Installation foot
connection holes
Apply the silicone on
the glass surface.
Apply the supplied silicone around
Glass
Silicone seal
Tray
Connection apparatus
The installed appearance of the
cooker should be as shown in the
PIace the installation
feet as shown in the

7
ENGLISH TECHNICAL PASSPORT
Gas hob
INSTALLATION PREPARATIONS OF THE BUILT
-IN GLASS
COOKER
INSTALLATION OF THE COOKER
The cooker has a seal to prevent the liquids from owing from the gaps into
the cabinet. For xing this seal, attach it as shown in the gures ahove. Turn upside
down the cooker and remove the protective band of the rubber seal; both ends of
it should meet perfectly. Install the installation sheets by help of screw as shown
in the gure 5.
And then place the cooker into the clearance of the worktop.
Figure 1
Figure 1
Figure 4
Figure 4
Figure 5
Figure 5
Figure 6
Figure 6
Figure 2
Figure 2
Figure 3
Figure 3
Worktop
Cooker
installation sheet
Fixing points for the installation sheet
screw
Put your cooker upside down in the
styrofoam taken from the package and
apply the silicone.
Installation foot
connection holes
Apply the silicone on
the glass surface.
Apply the supplied silicone around
Glass
Silicone seal
Tray
Connection apparatus
The installed appearance of the
cooker should be as shown in the
PIace the installation
feet as shown in the

8
TECHNICAL PASSPORT ENGLISH
Gas hob
Figure 3Figure 4
Figure 1Figure 2
UPPER TRAY
SILICONE SEAL
WORKTOP SURFACE
CONNECTION CLIP
SCREW
INSTALLATION OF THE BUILT
-IN COOKER 400 SERIES
Worktop cutting measure is given in Figure 7 for placing the cooker. Into the
worktop cut to these measures, place the cooker of which the initial preparations
were performed.
If you will use the cooker on the built-in oven, then comply with the Figures
8and 9 for proper clearance between the oven and cooker to allow air circulation.
Please place the silicone seal along the edges of the cooker (Figure 1). Finally,
you. should x it on the lower edges of the work surface by means of clamps and
screws (Figure 2).

9
ENGLISH TECHNICAL PASSPORT
Gas hob
Position the product so as to reach
to the power cord. Supply voltage of
your product is 220Y. The earth plug
on the power cord should be denitely
used with an earthed power socket.
ÂOur products are fueled by
liqueed petroleum gas or natural gas
depending on its version (optional).
ÂApply to the authorized service
center to switch your product to
liqueed petroleum gas or Natural Gas.
ÂHave the mains connection and
earthing installation by a qualied
electrician.
ÂOur rm may not be held
responsible for any damages that may
arise from failure to comply with the
instructions given above.
ÂWhen you use your cookers
with liqueed petroleum gas, use
pressurereducing valve TSE 300 mm SS
with outlet pressure of 1.5 kg/h.
Connect your product to liqueed
petroleum gas cylinder by the short
plastic hose in a gas-proof manner.
Connect your product to the Natural
Gas cock by the spiral hose in a gas-roof
manner.
The hose to be used should not
be longer than 125cm for safety
purpose.
When placing your product, take
care that the gas hose or power cord
does not remain under the body. Do not
SECTION 3.
THINGS TO BE CONSIDERED PRIOR TO USE OF THE TABLE
TOP COOKER AND SAFETY WARNINGS
run it near the burners, otherwise cable
insulation may he damaged.
When the power cord is damaged,
replace it by visiting the nearest author-
ized service center.
When gas connection is completed,
do not move your product beyond the
limits that the gas hose allows. Any
forcing may cause gas leakage from the
hose connections.
Do not operate it without
putting pan, etc. on the electric
cooker.
The stainless steel around the elec-
tric cooker may change color due to
heat. It is not problem for use of it.
In order to make your product ready
for use, you should rst prepare the in-
stallation place and complete the elec-
tric installation.
And then call our authorized service
personnel.
Note: Start use after removal
of the protective lm on Inox
surface.

10
TECHNICAL PASSPORT ENGLISH
Gas hob
SECTION 4.
IDENTIFICATION OF THE CONTROL PANEL AND USE OF THE
BURNERS
Gas burning control buttons
The cocks controlling the gas burners of your product have spe-
cial safety equipment. To ensure gas ow through the cocks, you
should slightly push and turn left the buttons. To obtain optimum
efciency from the gas-fueled cookers, be careful about size of the
can you will put on the cooker. Please refer to the following gure
for this purpose.
Ignition System
Your product has two types of ignition system depending on the version of it. If
the ignition system of the version of the product you purchased is controlled by an
external button, then you should slightly push the button for the burner you desire
tooperate and then turn left, turn anti-clockwise, to ensure gas ow. Just after turn-
ing on the button, push the lighter ignition button and hold it till ignition. After
ignition, release the lighter button. You should repeat the procedure in each case.
If your product has gas button with lighter (as shown in the gure above), push the
button slightly and turn left till the symbol of lighter ignition. The lighter will start
to ignite the burners. While the lighter ignites, it also ignites. After ignition, turn the
button to the symbol Big ame or Small ame to determine the burning position.
The lighter ignition will stop and burning will continue. If it does not ignite, then
continue this process until the ignition is performed.
Кнопки управления газовыми горелками
Металлическая
мочалка
Чистящий
порошок
Спрей для
духового
шкафа
Жесткая губка, вызывающая
коррозию
-
Gas burning control buttons
Steel wool Cleaning
powder
Oven
Spray
Corrosive
hard sponge