Kuppersbusch KD 380.1 GE Operation manual

BEDIENUNGSANWEISUNG
mit Montageanweisungen
7;<:=,,287.;-.&;8A-.87<*3.
7;<:=,<287;/8:=;.*7-27;<*55*<287
7;<:=,<287;-U=<252;*<287.*>2;-.687<*0.
7;<:=CD.;-.=;8,8627-2,*CD.; 9*:*687<*0.6
;<:=B2872-2=;8.-2687<*0028
:=4;8,1687<.:270;*7>2;7270*:
.+:=24;**7?23B270.7687<*0.1*7-5.2-270
[p~Qt{tPnz}wQSt|cPrpnQRi{mRQ€R
KD 380.1 GE
(Rev. 0)
_____________________________________________________

ENG
Dear client
Congratulations on your choice. We are sure that
this modern, functional and practical appliance,
made with top quality materials, will fully satisfy
your needs.
Please read every section of this INSTRUCTIONS
MANUAL before using your kitchen hood for the
first time, to ensure maximum performance from
the appliance and to avoid breakdowns, which
may be caused by incorrect use, as well as to
allow any minor problems to be solved.
Store this manual, as it will provide useful
information about your kitchen hood at all times
and will also help other people to use it.
• Please be aware of current local regulations
with reference to domestic electrical fittings and
gas eduction.
• Verify that the tension and frequency of the
network match those indicated on the label
located inside the kitchen hood.
• If the supply cable is damaged it should be
replaced by the manufacturer, the after-sales
service or a suitably qualified person in order to
avoid hazard.
• In case your cooker hood is not provided with a
plug for the mains connection or is not
accessible in normal conditions it is necessary
to install a disconnection switch to the house
installation, according to the local standards for
installations.
• Make sure a good ground connection (this
does not apply to class II appliances, indicated
accordingly on the rate plate with )
• Once the kitchen hood has been installed,
ensure that the mains cable to the network is
not in contact with any live metal edges.
• Avoid connecting the appliance to conductors
used as exits for fumes produced by a non-
electric energy source, e.g.: boilers, chimneys,
etc.
• If the extractor fan is going to be used simulta-
neously with equipment powered by a non-
electric energy source, e.g.: gas cookers, then
the room must have sufficient ventilation.
• Excessive fat accumulation in the kitchen hood
and metal filters is a fire risk and may also
cause dripping, therefore the inside of the
kitchen hood and the metal filters must be
cleaned at least once a month.
• The lower part of the kitchen hood must be
fitted at least 65cm. over gas or mixed hobs.
FOLLOW THE HOBS´ MANUFACTURER'S
MINIMUM RECOMMENDATIONS. This
distance can be reduced if this is indicated by
the manufacturer in the cooker hood instruction
manual.
• Never leave gas hobs lit if not covered by a
container. The fat accumulated in the filters
may drip or catch fire when the temperature
increases.
• Avoid cooking under the kitchen hood if the
metal filters are not fitted, e.g.: while they are
being cleaned in the dishwasher.
• You must not produce flames under the kitchen
hood.
• Do not place anything on top of the cooker
hood.
• Disconnect the appliance before any interior
manipulation, e.g. during cleaning or
maintenance.
• We recommend the use of gloves and to be
extremely careful when cleaning the kitchen
hood's interior.
• Your kitchen hood is designed for domestic use
and only for extraction and purification of fumes
produced during food preparation. It will be
your responsibility if it is used for other
purposes, which may be dangerous. The
manufacturer cannot accept responsibility for
damage caused by improper use of the
appliance.
• For repairs please contact the nearest
KÜPPERSBUSCH Technical Assistance
Service, and always use genuine spare parts.
Repairs or modifications carried out by
unqualified personnel can cause malfunctions
or may damage the appliance, putting your
safety in danger.
• This appliance is marked according to the
European directive 2002/96/EC on “Waste
Electrical and Electronic Equipment” (WEEE).
This guideline is the frame of a European-wide
validity of return and recycling on Waste
Electrical and Electronic Equipment, .
• When the cooker hood is run at the same time
as other than electrical appliance or equipment
with different energy source, the air extraction
(underpressure) must no be higher than 4Pa (4
x 10-5 bar).
• This device is not meant to be used by persons
(including children) whose physical, sensory or
mental capacities are reduced, or who lack
experience/knowledge, except if they have
supervision or received instructions for using
the device by the person responsible for his/her
safety. Keep children away from the device and
never let them play with it.
Safety Instructions
10

ENG
ndex
age
Description of the appliance 11
Instructions for use 11
rogramming timer 11
Cleaning and maintenance 12
roblem solving 12
Sizes and specifications 12
Accessories supplied 13
Installation 13
Active charcoal filters 13
AOn/ Off electronic push button, speed
selector, light and working pilot.
BMetal filters.
CLamp with bulbs - '
D, E Vertically adjustable tubecovers.
FDecorative part.
Switch on the extractor fan a few minutes
before you start to cook in order to ensure that
a steady air flow has been established before
fumes appear.
Allow the extractor fan to run for several
minutes after you have finished cooking
(between 3 to 5 minutes) in order to expel all
the grease from the outlet duct. This prevents
the return of grease, smoke and smells.
Proceed as follows:
1.- Choose the required speed.
2.- Press "timer". The light will begin to flash.
The duration of the “timer” is 10 min.
During the programmed time, fan speed can
be changed.
The intensive speed is autoprogramed and
will change to speed 2 after approximately 10
minutes.
Description of the appliance
Instructions for use
You may control the kitchen hood by
operating the controls as shown in the
diagram.
Programming timer
11

ENG
KÜ ERSBUSCH reserves the right to make changes and corrections to its products as it
deems necessary, without altering their basic characteristics.
During cleaning and maintenance work,
make sure the safety instructions set out
on page 10 are complied with.
• f your kitchen hood is made from stainless
steel, use proprietary cleaners mentioned
in the product instructions.
• Never use metallic scourers, nor abrasive
or corrosive products.
• Dry the kitchen hood using a cloth that
does not produce fibres.
• The use of vapour cleaners is not
recommended.
To remove the filters from their fittings, press
lightly on the locks and then pull them off.
The metal filters can be cleaned by soaking
them in hot water with neutral detergent until
the fat dissolves and then rinsing them under
the tap or using special anti-grease products.
They can also be washed in a dishwasher. n
this case, it is advisable to stack them
vertically to avoid food residues to stick to
them.
Cleaning in a dishwasher may damage the
metallic surface (blackening it), although this
will not affect its fat retention capacity.
Once clean, leave them to dry off and then fit
them onto the kitchen hood.
Fig. 3 (Page 39)
Proceed as follows:
• Remove the metal filters.
• Loosen the screws (A) to dismount the
cover top (B).
• Change the broken/ burnt out lamp.
Maximum lamp power is 9W (E-14).
• Mount the cover top again (B).
• Fit the metal filters.
Cleaning and maintenance
_________________________________________________________
roblem solving
Proceed with the following checks before calling the Technical Service:
Cleaning the hood body
Cleaning the metal filters
Changing light bulbs
Sizes and specifications
See page 38.
12

.
1 150/ 120 mm reduction.
1 Anti-recoil valve.
2 Supports for tubecover.
2 Supports hall.
6 Wall plugs (Ø8 x 40).
6 Long bolts (Ø5 x 45).
4 Wall plugs (Ø6 x 30).
4 Long bolts (Ø4 x 30).
2 Washers (Ø6.4 x Ø18).
2 Washers (Ø6.4 x Ø12).
2 Screws (Ø3.9 x 19).
4 Screws M4 x 12.
2 Clips.
Fig. 1 ( age 39)
On installing the kitchen hood make sure
that the Safety Instructions set out on
page 10 are complied with.
To obtain optimum performance, the external
duct must not be more than FOUR METRES
LONG, have no more than two 90° angles and
its diameter must be at least Ø120.
1) Trace and drill the points for fitting the wall
plugs onto the wall (P) (Ø8 x 40) and (J) (Ø6
x 30). See figure 1.
2) Attach the Supports (O) to the wall using
the long bolts (Q) (Ø5 x 45) and the support
(H) with the long bolts ( ) (Ø4 x 30), as in
figure 1.
3) Fit the body of the hood to the support (O)
and level the hood using the long bolts (L) (M4
x 12).
4) Trace the location of the wall plugs (R) (Ø8
x 40), through the inside of the kitchen hood.
5) Take the kitchen hood off.
6) Drill into the wall and fit the wall plugs (R)
(Ø8 x 40).
7) Hang the kitchen hood; tighten the screws
(M) (M4 x 12) with the washers (A3) (Ø6.4 x
Ø12) and the long bolts (S) (Ø5 x 45) with the
washers (T) (Ø6.4 x Ø18).
8) Mount the tubecovers, attaching the lower
one to the support (H) as per the detail in
figure 1. Lift the upper tubecover up to the
desired height and mark its shape on the wall.
Remove the tubecovers.
9) Fit the clips (F) to the support (C).
10) Centre the support (C) around the shape
marked; trace and drill the fixing points for the
wall plugs (E) (Ø6 x 30). Attach the support
(C) with the long bolts (D) (Ø4 x 30).
11) Fit the part (A) if the inner tube (not
supplied) is Ø150 or (A) + (B) if it is Ø120.
12) Attach the inner tube with a clamp (not
supplied) to (A) or (B) as the case may be.
13) Once the inner tube has been fitted, fit the
lower tubecover around the extractor fan
outlet and attach the upper tubecover with the
screws (G) (Ø3.9 x 19).
When exterior gas extraction is not possible,
then the kitchen hood may be set to purify the
air by recycling it through active charcoal
filters.
The active charcoal filters have an active life
of between three to six months, depending on
the individual conditions of use. These filters
cannot be washed nor regenerated. They
must be replaced once their useful life comes
to an end.
Fig. 2 ( age 39)
1) Remove the metal filters.
2) Put the charcoal filters (A) into the lateral
draught section (B) of the motor.
3) Fit the metal filters.
4) Remove the tubecovers (H). Fit the support
(J) in the diffuser (C). Mount the connector
Ø150 (L) in the diffuser base.
5) Use the wall plugs and the previously
installed upper tubecover's support ( ) long
bolts (D) (Ø4 x 30) to fix diffuser into the wall
(C).
6) Connect the connector base (L) to the
motor exit via the inner tube (not supplied).
Use clamps (Not supplied). Fit the tubecovers
(H) again.
Installation
ENG
Accesories supplied
13
Active charcoal filters (Optional)

38 [vlpySQSrxgOw…lvOgQ~xtu„xiO{OuSr{tRStu„xwlRORSzxO…z{{zTrSm{O
* Zie beschrijving van de eignschappen in het interieur van de afzuigkap.
* Se nformationsbricka inuti fläktkåpan.
* Vedere Placca di Caratterístiche all'interno della cappa.
.1
* Vêr Placa de características no interior do exhaustor.
* Voir Plaque des Caractéristiques à l´intérieur de la hotte.
* Check Characteristics label inside the hood.
* Ver Placa de Características en el interior de la campana.
* Siehe Typenschild im nnern der Dunstabzughauben.
.1.1.1

39