Kurzweil K2500 User manual

Effects
List of Factory Preset Global Effects and Their Configurations
3-1
Chapter 3
Effects
List of Factory Preset Global Effects andTheir Configurations
ID# Name Configuration
1Sweet Hall Ultimate Reverb
2Small Hall Room Simulator
3Medium Hall Ultimate Reverb
4Large Hall Ultimate Reverb
5Big Gym Room Simulator
6Bright Plate 1 Ultimate Reverb
7Opera House Ultimate Reverb
8Live Chamber Room Simulator
9Bathroom Ultimate Reverb
10 Med Large Room Room Simulator
11 Real Room Ultimate Reverb
12 Drum Room Room Simulator
13 Small Dark Room Room Simulator
14 Small Closet Ultimate Reverb
15 Add Ambience Room Simulator
16 Gated Reverb Gated Reverb
17 Reverse Reverb Reverse Reverb
18 Non-Linear Ultimate Reverb
19 Slapverb Room Simulator
20 Full Bass Chorus+Delay+Room+Mixer
21 Room & Delay Delay+Room+Mixer
22 Delay Big Hall Delay+Hall+Mixer
23 Chorus Room Chorus+Room+Mix
24 Chorus Smallhall Chorus+Hall+Mix
25 Chorus Med Hall Chorus+Hall+Mix
26 Chorus Big Hall Chorus+Hall+Mix
27 Chor-Delay Room Chorus+Delay+Room+Mixer
28 Chor-Dly Hall Chorus+Delay+Hall+Mixer
29 Flange-Dly Room Flange+Delay+Room+Mixer
30 Flange-Dly Hall Flange+Delay+Hall+Mixer
31 Stereo Chorus Stereo Chorus
32 Stereo Flanger Stereo Flange
33 Stereo Delay 4-Tap Delay
34 4 Tap Delay 4-Tap Delay
35 Chorus Delay Parametric EQ+Chorus+Delay+Mixer
36 Flange Delay Parametric EQ+Flange+Delay+Mixer
37 Chorus 4 Tap EQ+Chorus+4 Tap Delay+Mixer
100 Flange 4 Tap EQ+Flange+4 Tap Delay+Mixer
101 Chorus Echo EQ+Chorus+4 Tap Delay+Mixer
102 Chorus Echoverb EQ+Chorus+4 Tap Delay+Mixer
103 Fast Flange Stereo Flange
104 Wash Chorus+Delay+Hall+Mixer
105 Into the Abyss Chorus+Delay+Hall+Mixer
106 Space Flanger EQ+Flange+4 Tap Delay+Mixer
107 Flange Room Flange+Delay+Hall+Mixer
108 Predelay Hall Delay+Hall+Mixer
109 Flange Echo EQ+Flange+4 Tap Delay+Mixer

Effects
Effects Controller Numbers
3-2
Effects Controller Numbers
The K2500 uses the Digitech 256 chip for its effects processor. When in Program Mode, the
operating system allows you to assign any MIDI controller to Wet/Dry Mix plus two additional
parameters related to the effect. (The choice of controllable parameters changes depending on
the effect configuration. They are the parameters you see when you go to edit the effect.)
But if the FX Mode parameter on the Effects page is set to Master, then the remapping that takes
place within the program is not applied. Instead, you use a predefined set of controller
numbers. So to control the effects processor in real time when FX Mode is set to Master, you
must use the following controller numbers.
To control the effects processor in this manner, press the EFFECTS button. Change FX Mode to
Master, and set FX Chan to the channel you will use to send the controller info. (You can also
send program changes on this channel to switch effects, so it is usually best to pick a channel
that is not being used for notes.) These settings are remembered as long as the Power Mode
parameter on the MIDI receive page is set to User. Otherwise, you will have to re-enter the
settings each time you power up.
In the following chart, the parameters are grouped by Configuration. Multi FX will contain
parameters found in more than one configuration.
Ultimate Reverb
Decay time 77
Room volume 78
HF damping 14
Envelopment 32
Early Delay 29
Early Diffusion 30
Later Delay n/a
Later Diffusion 93
Dry Level 28
Early Level 31
Later Level 92
Room Simulation
Gross Size 90
Decay Time 15
Listening Position 79
HF Damping 14
Dry Level 28
Reverb Level 88
Reverb in Multi FX
RevPre-Delay 80
Hi-Freq Damp 83
Reverb Decay 82
Revin dry 86
Revin flange 87
Revin Delay 85

Effects
Effects Controller Numbers
3-3
Gated Reverb
Pre-Delay 80
Decay Time 38
Envelope 39
Accent Dly 01
Dry Level 57
Accent Level 02
Right Level 62
Left Level 94
Reverse Reverb
Pre-Delay 80
Reverse Time 89
Accent Delay 01
Accent Level 02
Dry Level 57
Right Level 66
Left Level 65
Accent Lvl L 50
Accent Lvl R 51
Parametric EQ
Band 1 Freq 03
Band 1 level 04
Band 2 Freq 05
Band 2 level 06
Band 3 Freq 07
Band 3 level 08
EQ level 58
Graphic EQ
63 Hz 41
125 Hz 43
250 Hz 45
500 Hz 47
1.0 Khz 42
2.0 Khz 44
4.0 Khz 46
8.0 Khz 48
Stereo Chorus
Chorus Delay 10
LFO Speed 13
LFO Depth 12
Dry Level 57
Right Level 54
Left Level 52
Chorus Level 53

Effects
Effects Controller Numbers
3-4
Stereo Flange
Flange Delay 33
LFO Speed 37
LFO Depth 36
Feedback 35
Dry Level 57
Right Level 61
Left Level 59
Flange Level 60
Stereo Delay
Delay Time 22
Feedback 17
Dry Level 57
Right Level 56
Left Level 55
DelayDry In 19
Delay Chr In 18
Delay Flg In 21
Delay EQ In 20
Delay EQ Src 16
4Tap Delay
Tap 1 Delay 24
Tap 2 Delay 25
Tap 3 Delay 26
Tap 4 Delay 27
Feed Delay 23
Feedback 17
Dry Level 57
Tap 1 Level L,R 67, 68
Tap 2 Level L,R 69, 71
Tap 3 Level L,R 72, 74
Tap 4 Level L,R 75, 76
Tap 2 Level 70
Tap 4 Level 73
Other
Wet/Dry Mix 91
Bypass 09
LowPass Filter 49
NOTES:
In the interest of signal to noise performance, the effects dry level parameter should be left at 0
and the Wet/Dry mix (91) should be used instead.
Some of the above parameters may only be found in a Multi FX patch.