KWIK GOAL 2F501 User manual

NZ261 Rev. 09/26/18
ASSEMBLY INSTRUCTIONS FOR 2F501 FIELD HOCKEY GOAL
1. Unpack all parts and check for damage that may have occurred during shipping. If damage has occurred,
notify Kwik Goal immediately. Lay out all parts. Remove all cardboard and packaging immediately. Wet or
damp packaging may damage contents.
2. Read through entire instruction before beginning assembly and installation.
3. A minimum of two qualified persons are required to assemble this goal.
NOTE: Components may be packaged in one or more additional boxes.
140 Pacific Drive Quakertown, PA 18951
(P) 215-536-2200 / (P) 800-531-4252 / (F) 215-536-4309 / (F) 800-778-8869
Visit our website @ kwikgoal.com
2011 Rev 2018 Kwik Goal Ltd.
Right Arm (1)
2F501(Part# UZ733)
Left Arm (1)
2F501(Part# UZ738)
End
View
Crossbar (1)
2F501(Part# UZ734)
***CAUTION***
This equipment has been designed to be used for the game of field hockey only. Field equipment
must be anchored AT ALL TIMES and shall be secured against overturning. Do not climb on the net
or equipment framework at anytime! All fastenings must be checked to insure they are fully
tightened before and after each use of this product. Equipment not in use must be disassembled
and properly stored in a safe, secure area. Assembled field equipment should not be left
unattended. Remove nets when equipment is not in use. Do not use this equipment during the
threat of high winds. Field equipment must be checked for safety before and after each use. All
warning and safety labels included with this product must be visible at all times. Any modifications
to this or any Kwik Goal product will void any and all warranties.
136”
Side Board (2)
(Part# WZ1176-03)

NZ261 Rev. 09/26/18
140 Pacific Drive Quakertown, PA 18951
(P) 215-536-2200 / (P) 800-531-4252 / (F) 215-536-4309 / (F) 800-778-8869
Visit our website @ kwikgoal.com
2018 Kwik Goal Ltd.
IMPORTANT GOAL SAFETY INSTRUCTIONS
READ CAREFULLY
1. Check for structural integrity and proper connecting hardware before every
use. Replace damaged or missing parts or fasteners immediately.
2. Safety/Warning labels must be clearly visible.
3. Securely anchor moveable goals at ALL times.
4. Always instruct players, managers, coaches, trainers, teachers, maintenance
workers and all other personnel who might come in contact with the goal,
on the safe handling of and potential dangers associated with moveable
goals.
5. Always exercise extreme caution when moving goals and provide adequate
manpower to move goals of varied sizes and weights. Moveable goals
should only be moved by authorized personnel.
6. NEVER allow anyone to climb on the net or goal framework.
7. Moveable goals should only be used on LEVEL fields, NEVER on a slope or
hill area.
8. Remove nets when goals are not in use.
9. Most of the tip-over injuries occurred when goals were unattended. Anchor
or chain one goal to another or to nearby fence posts, dugouts, or any other
similar sturdy fixture when not in use. If this is not practical, store moveable
goals in a place where children cannot have access to them.
10. Fully disassemble goals for seasonal storage.
WARNING

Hardware
Note: Hardware may be packaged separately
in one or more boxes. Open all packages
before beginning assembly.
1/4” x 2” Eye Bolt (Part# TZ23) (2)
1/4” Lock Nut (Part# TZ19) (2)
1/4“ Flat Washer (Part# TZ147) (2)
3/8” X 1-1/4” Hex Bolt (Part# TZ59) (4)
3/8” X 2-1/2” Hex Bolt (Part# TZ165) (4)
3/8” Lock Nut (Part# TZ197) (4)
3/8” Flat Washer (Part# TZ60) (12)
3/8” Lock Washer (Part# TZ65) (4)
7/16” X 3-1/2”Bolt Carriage (Part# TZ230)(4)
7/16” Hex Nut (Part# TZ211) (4)
7/16” Lock Washer (Part# TZ210) (4)
7/16” Flat Washer (Part# TZ171) (4)
Assembly Tools
9/16
7/16”, 9/16”, 5/8” & 3/4”
Wrenches
Ratchet with
7/16”, 9/16”, 11/16” & 3/4”
Sockets
AND
Secure Net Clip
Driver (1)
(Part# VZ140)
Back Board (1)
2F501(Part# UZ735)
Net (1)
2F501(Part# 3F501)
Ground Anchor (4)
Includes Hex Bolt
and Flat Washer
(Part# 10B103 Set of 4)
16”
Ground
Anchor Peg (4)
(Part# 10B1404 Pack of 4)
Anchor Plate (4)
(Part# UZ736)
Anchor Bag (2)
(Part# 10B1605)
Channel Spacer (2)
(Plastic)
(Part# UZ812)
Secure Net Clip (50)
(Part# 10B3401 Pack of 100)
NZ261 Rev. 09/26/18
***CAUTION***
This equipment has been designed to be used for the game of field hockey only. Field equipment
must be anchored AT ALL TIMES and shall be secured against overturning. Do not climb on the net
or equipment framework at anytime! All fastenings must be checked to insure they are fully
tightened before and after each use of this product. Equipment not in use must be disassembled
and properly stored in a safe, secure area. Assembled field equipment should not be left
unattended. Remove nets when equipment is not in use. Do not use this equipment during the
threat of high winds. Field equipment must be checked for safety before and after each use. All
warning and safety labels included with this product must be visible at all times. Any modifications
to this or any Kwik Goal product will void any and all warranties.
Back Board (2)
(Part# WZ1176-02)

4. Lay out right arm assembly and left arm assembly face down on turf as shown. Insert channel spacers into
channel on each side of crossbar. Insert sleeve of left and right arm assemblies into crossbar. Line up all
holes. Connect crossbar with hex bolts as shown. Press joints together firmly before tightening bolts.
CAUTION: DO NOT OVER TIGHTEN BOLTS.
3/8” Flat Washer
Right Arm
Assembly
3/8” X 1-1/4” Hex Bolt
3/8” Lock Washer
Channel
Spacer
Crossbar
Left Arm Assembly
Right Arm Assembly
Crossbar
NZ261 Rev. 09/26/18
***CAUTION***
This equipment has been designed to be used for the game of field hockey only. Field equipment
must be anchored AT ALL TIMES and shall be secured against overturning. Do not climb on the net
or equipment framework at anytime! All fastenings must be checked to insure they are fully
tightened before and after each use of this product. Equipment not in use must be disassembled
and properly stored in a safe, secure area. Assembled field equipment should not be left
unattended. Remove nets when equipment is not in use. Do not use this equipment during the
threat of high winds. Field equipment must be checked for safety before and after each use. All
warning and safety labels included with this product must be visible at all times. Any modifications
to this or any Kwik Goal product will void any and all warranties.

5. Attach back board and fasten eye bolt to back drop on left and right arm assemblies as shown.
IMPORTANT: FIELD HOCKEY BOARDS HAVE BEEN DESIGNED FOR GAME USE ONLY. CLOSE-RANGE
SCORING PRACTICE WILL CAUSE PERMANENT DAMAGE TO BOARDS.
3/8” Flat Washer
3/8” Flat Washer
3/8” Lock Nut
3/8” X 2-1/2”Hex Bolt
Back Board
Note: You can use secure net clip
driver to hold eye bolt while
installing lock nut.
Secure Net Clip Driver
1/4” X 2” Eye Bolt
Back Board
Back Drop
1/4” Lock Nut
1/4” Flat Washer
1/4” X 2” Eye Bolt
NZ261 Rev. 09/26/18
***CAUTION***
This equipment has been designed to be used for the game of field hockey only. Field equipment
must be anchored AT ALL TIMES and shall be secured against overturning. Do not climb on the net
or equipment framework at anytime! All fastenings must be checked to insure they are fully
tightened before and after each use of this product. Equipment not in use must be disassembled
and properly stored in a safe, secure area. Assembled field equipment should not be left
unattended. Remove nets when equipment is not in use. Do not use this equipment during the
threat of high winds. Field equipment must be checked for safety before and after each use. All
warning and safety labels included with this product must be visible at all times. Any modifications
to this or any Kwik Goal product will void any and all warranties.

Ground Anchor
1/2" x 4" Hex Bolt
1/2" Flat Washer
Right Arm
Assembly
6. For ground anchor use, mark ground anchor hole location, move goal and dig holes a minimum of 24“ in
diameter and 20” deep as shown. Areas subject to heavy ground frost may go as deep as 36”. Attach ground
anchors to assembled goal and secure with coated bolts. Set goal in desired installation location with anchors
in holes. Fill area surrounding the anchor with concrete.
NOTE: When removing goal from field location,
be sure to disassemble and store in a safe place
to prevent injury. (If ground anchors are used,
insert red ground anchor caps into exposed
ground anchor holes to prevent damage to
threads.)
IMPORTANT
Ground anchors are the recommended and
safest method of anchoring your goal.
For anchoring options see steps 7 or 10.
Anchor Hole Detail
(4 places per goal)
Ground Anchor
Field Surface
20”
Min
12-3/4”
24” Min
Concrete Concrete
Stone
60°
Approx.
NZ261 Rev. 09/26/18
***CAUTION***
This equipment has been designed to be used for the game of field hockey only. Field equipment
must be anchored AT ALL TIMES and shall be secured against overturning. Do not climb on the net
or equipment framework at anytime! All fastenings must be checked to insure they are fully
tightened before and after each use of this product. Equipment not in use must be disassembled
and properly stored in a safe, secure area. Assembled field equipment should not be left
unattended. Remove nets when equipment is not in use. Do not use this equipment during the
threat of high winds. Field equipment must be checked for safety before and after each use. All
warning and safety labels included with this product must be visible at all times. Any modifications
to this or any Kwik Goal product will void any and all warranties.

7. For ground anchor peg use only, attach anchor plate.
Ground Anchor Peg
Anchor Plate
7/16” Hex Nut
7/16” Lock Washer
7/16” Flat Washer
Anchor Plate
7/16” X 3-1/2”
Carriage Bolt
NZ261 Rev. 09/26/18
***CAUTION***
This equipment has been designed to be used for the game of field hockey only. Field equipment
must be anchored AT ALL TIMES and shall be secured against overturning. Do not climb on the net
or equipment framework at anytime! All fastenings must be checked to insure they are fully
tightened before and after each use of this product. Equipment not in use must be disassembled
and properly stored in a safe, secure area. Assembled field equipment should not be left
unattended. Remove nets when equipment is not in use. Do not use this equipment during the
threat of high winds. Field equipment must be checked for safety before and after each use. All
warning and safety labels included with this product must be visible at all times. Any modifications
to this or any Kwik Goal product will void any and all warranties.

8. Remove net rope from net and attach to the top back of goal as shown.
Note: Make net rope taut so net will look and perform as designed.
Eye Bolt
Net Rope
Net Rope
Eye Bolt
NZ261 Rev. 09/26/18
***CAUTION***
This equipment has been designed to be used for the game of field hockey only. Field equipment
must be anchored AT ALL TIMES and shall be secured against overturning. Do not climb on the net
or equipment framework at anytime! All fastenings must be checked to insure they are fully
tightened before and after each use of this product. Equipment not in use must be disassembled
and properly stored in a safe, secure area. Assembled field equipment should not be left
unattended. Remove nets when equipment is not in use. Do not use this equipment during the
threat of high winds. Field equipment must be checked for safety before and after each use. All
warning and safety labels included with this product must be visible at all times. Any modifications
to this or any Kwik Goal product will void any and all warranties.

9. Put net over goal frame and attach with secure net clips using net clip driver as shown.
Place base of secure net clip into channel and turn 90 degrees to lock into place.
CAUTION: DO NOT ATTEMPT TO CLIMB ON GOAL WHILE ATTACHING NET.
Secure Net Clip
Secure Net Clip Driver
Secure Net Clip
Secure Net Clip Driver
NZ261 Rev. 09/26/18
***CAUTION***
This equipment has been designed to be used for the game of field hockey only. Field equipment
must be anchored AT ALL TIMES and shall be secured against overturning. Do not climb on the net
or equipment framework at anytime! All fastenings must be checked to insure they are fully
tightened before and after each use of this product. Equipment not in use must be disassembled
and properly stored in a safe, secure area. Assembled field equipment should not be left
unattended. Remove nets when equipment is not in use. Do not use this equipment during the
threat of high winds. Field equipment must be checked for safety before and after each use. All
warning and safety labels included with this product must be visible at all times. Any modifications
to this or any Kwik Goal product will void any and all warranties.

10. Counterbalance weight may be used as a temporary anchoring system. To ensure counterbalance weight
remains on the base of your goal you must attach counterbalance weight as shown in figure below.
NOTE: See steps 8 & 9 to attach net before using counterbalance weight.
NZ261 Rev. 09/26/18
***CAUTION***
This equipment has been designed to be used for the game of field hockey only. Field equipment
must be anchored AT ALL TIMES and shall be secured against overturning. Do not climb on the net
or equipment framework at anytime! All fastenings must be checked to insure they are fully
tightened before and after each use of this product. Equipment not in use must be disassembled
and properly stored in a safe, secure area. Assembled field equipment should not be left
unattended. Remove nets when equipment is not in use. Do not use this equipment during the
threat of high winds. Field equipment must be checked for safety before and after each use. All
warning and safety labels included with this product must be visible at all times. Any modifications
to this or any Kwik Goal product will void any and all warranties.
Go to kwikgoal.com for additional product information.

Mounting Bracket (2)
(Part# UZ690)
NZ416 Rev. 02/23/17
ASSEMBLY INSTRUCTIONS FOR 2F501 WHEELS
1. Unpack all parts and check for damage that may have occurred during shipping. If damage has occurred,
notify trucking company immediately. Lay out all parts. Remove all cardboard and packaging immediately.
Wet or damp packaging may damage contents.
2. Read through entire instruction before beginning assembly and installation.
140 Pacific Drive Quakertown, PA 18951
(P) 215-536-2200 / (P) 800-531-4252 / (F) 215-536-4309 / (F) 800-778-8869
Visit our website @ kwikgoal.com
2017 Kwik Goal Ltd.
Tire and Wheel Assembly (2)
(Part# VZ349)
Stop Plate (2)
(Part# UZ1254)
Hardware
Note: Hardware may be packaged separately
in one or more boxes. Open all packages
before beginning assembly.
3/8” x 1” Hex Bolt (Part# TZ1) (4)
3/8" x 3/4" Socket Hd Capscrew (Part# TZ208) (2)
3/8“ Lock Washer(Part# TZ65) (4)
3/8“ Flat Washer (Part# TZ60) (4)
3/8” Lock Nut (Part# TZ370) (2)
1/2” Flat Washer (Part# TZ297) (2)
1/2" Lock Nut (Part# TZ28) (2)
5/8" x 3 1/2” Hex Bolt (Part# TZ369) (2)
5/8” Lock Nut (Part# TZ294) (2)
5/8” Jam Nut (Part# TZ108) (2)
Large Nylon Washer (Part# TZ204) (2)
Assembly Tools
9/16
9/16”, 3/4” & 15/16”
Wrenches
Ratchet with
9/16”, 3/4” & 15/16”
Sockets
5/16” Hex
Wrench
Threaded Channel Spacer (2)
(Part# UZ691)
***CAUTION***
This equipment has been designed to be used for the game of field hockey only. Field equipment
must be anchored AT ALL TIMES and shall be secured against overturning. Do not climb on the net
or equipment framework at anytime! All fastenings must be checked to insure they are fully
tightened before and after each use of this product. Equipment not in use must be disassembled
and properly stored in a safe, secure area. Assembled field equipment should not be left
unattended. Remove nets when equipment is not in use. Do not use this equipment during the
threat of high winds. Field equipment must be checked for safety before and after each use. All
warning and safety labels included with this product must be visible at all times. Any modifications
to this or any Kwik Goal product will void any and all warranties.

1/2" Lock Nut
1/2" Flat Washer
Mounting
Bracket
5/8" X 3 1/2"
Hex Bolt
5/8" Jam Nut
Stop Plate
Large Nylon Washer
Apply two small (1/4” max) drops of
anti-seize to each side of washer.
Keep anti-seize close to center hole.
Left Side Wheel
3. Assemble left and right wheel assemblies.
NZ416 Rev. 02/23/17
***CAUTION***
This equipment has been designed to be used for the game of field hockey only. Field equipment
must be anchored AT ALL TIMES and shall be secured against overturning. Do not climb on the net
or equipment framework at anytime! All fastenings must be checked to insure they are fully
tightened before and after each use of this product. Equipment not in use must be disassembled
and properly stored in a safe, secure area. Assembled field equipment should not be left
unattended. Remove nets when equipment is not in use. Do not use this equipment during the
threat of high winds. Field equipment must be checked for safety before and after each use. All
warning and safety labels included with this product must be visible at all times. Any modifications
to this or any Kwik Goal product will void any and all warranties.
3/8" X 3/4" Socket Head Capscrew
3/8" Lock Nut
Tire and Wheel
Assembly
5/8" Lock Nut
Tighten nut snug,
then loosen until
Mounting Bracket can
rotate on Stop Plate.
Stop Plate
Mounting
Bracket

Right Side Wheel
4. Assemble right wheel assembly.
NZ416 Rev. 02/23/17
***CAUTION***
This equipment has been designed to be used for the game of field hockey only. Field equipment
must be anchored AT ALL TIMES and shall be secured against overturning. Do not climb on the net
or equipment framework at anytime! All fastenings must be checked to insure they are fully
tightened before and after each use of this product. Equipment not in use must be disassembled
and properly stored in a safe, secure area. Assembled field equipment should not be left
unattended. Remove nets when equipment is not in use. Do not use this equipment during the
threat of high winds. Field equipment must be checked for safety before and after each use. All
warning and safety labels included with this product must be visible at all times. Any modifications
to this or any Kwik Goal product will void any and all warranties.
1/2" Lock Nut
1/2" Flat Washer
Mounting
Bracket
5/8" X 3 1/2"
Hex Bolt
5/8" Jam Nut
Stop Plate
Large Nylon Washer
Apply two small (1/4” max) drops of
anti-seize to each side of washer.
Keep anti-seize close to center hole.
3/8" X 3/4" Socket Head Capscrew
3/8" Lock Nut
Tire and Wheel
Assembly
5/8" Lock Nut
Mounting
Bracket
Stop Plate
Tighten nut snug,
then loosen until
Mounting Bracket can
rotate on Stop Plate.

5. Attach left and right wheel assemblies to bases using threaded channel spacers as shown below.
NOTE:
If using wheel as back wheel move
wheel as far back as possible.
Mount wheels on outside of goal.
NOTE:
If using wheel as front wheel mount
wheel as far forward as possible.
Mount wheels on outside of goal.
NZ416 Rev. 02/23/17
***CAUTION***
This equipment has been designed to be used for the game of field hockey only. Field equipment
must be anchored AT ALL TIMES and shall be secured against overturning. Do not climb on the net
or equipment framework at anytime! All fastenings must be checked to insure they are fully
tightened before and after each use of this product. Equipment not in use must be disassembled
and properly stored in a safe, secure area. Assembled field equipment should not be left
unattended. Remove nets when equipment is not in use. Do not use this equipment during the
threat of high winds. Field equipment must be checked for safety before and after each use. All
warning and safety labels included with this product must be visible at all times. Any modifications
to this or any Kwik Goal product will void any and all warranties.
Right Tire & Wheel
Assembly
Threaded Channel Spacer
3/8” x 1” Hex Bolt
3/8" Lock Washer
3/8" Flat Washer
Right Tire & Wheel
Assembly
3/8” x 1” Hex Bolt
3/8" Lock Washer
3/8" Flat Washer
Threaded Channel Spacer

Right Arm Assembly Right Arm Assembly
Left Arm Assembly Left Arm Assembly
Lift
Front Post
Rotate
Stop
Stop
Lift
Front Post
Rotate
Stop
Stop
NZ416 Rev. 02/23/17
***CAUTION***
This equipment has been designed to be used for the game of field hockey only. Field equipment
must be anchored AT ALL TIMES and shall be secured against overturning. Do not climb on the net
or equipment framework at anytime! All fastenings must be checked to insure they are fully
tightened before and after each use of this product. Equipment not in use must be disassembled
and properly stored in a safe, secure area. Assembled field equipment should not be left
unattended. Remove nets when equipment is not in use. Do not use this equipment during the
threat of high winds. Field equipment must be checked for safety before and after each use. All
warning and safety labels included with this product must be visible at all times. Any modifications
to this or any Kwik Goal product will void any and all warranties.
Go to kwikgoal.com for additional product information.