KWIK GOAL 7E201 User manual

NZ328 Rev. 9/18/18
ASSEMBLY INSTRUCTIONS FOR 7E201 PORTABLE BACKSTOP
1. Unpack all parts and check for damage that may have occurred during shipping. If damage has occurred,
notify Kwik Goal immediately. Lay out all parts. Remove all cardboard and packaging immediately. Wet or
damp packaging may damage contents.
2. Read through entire instruction before beginning assembly and installation.
NOTE: Components may be packaged in one or more additional boxes.
140 Pacific Drive Quakertown, PA 18951
(P) 215-536-2200 / (P) 800-531-4252 / (F) 215-536-4309 / (F) 800-778-8869
Visit our website @ kwikgoal.com
2011 Rev 2018 Kwik Goal Ltd.
Parts
WARNING
THIS EQUIPMENT MUST BE STORED IN A SECURED, SHELTERED AREA WHEN NOT IN USE OR IN THE
THREAT OF HIGH WINDS. ANY WEATHER DAMAGE TO THIS EQUIPMENT WILL NOT BE COVERED
UNDER KWIK GOAL’S LIFETIME GUARANTEE. DO NOT LEAVE THIS EQUIPMENT UNATTENDED.
Brace (2)
(Part# UZ1295)
Heavy Duty
Anchor Bag (16)
(Part# 10B7011)
Base (4)
(Part# UZ1279)
Bottom Bar (3)
(Part# UZ1280)
234-1/2”
Upright (4)
(Part# UZ1278)
186”

Phillips Screw Driver
Assembly Tools
3. Attach swivel connector tube to all bases as
shown.
NOTE: Tighten 3/8” lock nuts only until
flush with end of carriage bolts.
Hardware
Note: Hardware may be packaged separately
in one or more boxes. Open all packages before
beginning assembly.
8-32 X 5/8” Flat Head Screw (Part# TZ314) (8)
1/4” Flat Washer (Part# TZ147) (4)
1/4” Lock Nut(Part# TZ19) (4)
3/8” Flat Washer (Part# TZ189) (6)
3/8” Lock Washer (Part# TZ301) (2)
3/8” Nut (Part# TZ166) (2)
3/8” Lock Nut (Part# TZ197) (4)
3/8” X 3” Threaded Stud (Part# JZ166) (2)
3/8” X 3-1/2” Carriage Bolt (Part# TZ340) (4)
27’ Rope (Part# VZ377) (4)
NZ328 Rev. 9/18/18
Base
3/8” Lock Nut
Swivel Connector Tube
3/8” Flat Washer
3/8” X 3-1/2” Carriage Bolt
Net Clip (40)
(Part# VZ116)
Net (1)
(Part# 3B4901)
Snap Link (4)
(Part# VZ82)
Square Nut & Stud (2)
(Part# JZ166)
Net Holder (8)
(Part# VZ431)
Knob (2)
(Part#JZ166)
Swivel Connector Tube (4)
(Part# UZ1296)
7/16” & 9/16”
Wrenches
Rope Cleat (4)
(Part# VZ569)
WARNING
THIS EQUIPMENT MUST BE STORED IN A SECURED, SHELTERED AREA WHEN NOT IN USE OR IN THE
THREAT OF HIGH WINDS. ANY WEATHER DAMAGE TO THIS EQUIPMENT WILL NOT BE COVERED
UNDER KWIK GOAL’S LIFETIME GUARANTEE. DO NOT LEAVE THIS EQUIPMENT UNATTENDED.
TZ339
VZ80
Pulley Assembly (4)
(Part# TZ339 & VZ80)

NZ328 Rev. 9/18/18
4. Set assembled bases and bottom bars in desired location and connect together with snap buttons.
Note: Bases at each end of unit must be connected to the fixed tube of the base assembly.
Assembled Base
Bottom Bar
Bottom Bar
Bottom Bar Assembled Base
Assembled Base
Assembled Base
Bottom Bar
Fixed Tube
Square Nut & Stud
Button
Square Nut & Stud
Assembled Base
Fixed Tube
Bottom Bar
Square Nut & Stud
Assembled Base
Bottom Bar
Bottom Bar
WARNING
THIS EQUIPMENT MUST BE STORED IN A SECURED, SHELTERED AREA WHEN NOT IN USE OR IN THE
THREAT OF HIGH WINDS. ANY WEATHER DAMAGE TO THIS EQUIPMENT WILL NOT BE COVERED
UNDER KWIK GOAL’S LIFETIME GUARANTEE. DO NOT LEAVE THIS EQUIPMENT UNATTENDED.

NZ328 Rev. 9/18/18
5. Fill each of the 16 heavy duty anchor bags with 40lbs of sand or gravel. Set 4 heavy duty anchor bags on
each assembled base as shown.
Heavy Duty Anchor Bag
Assembled Base
Heavy Duty Anchor Bag
Assembled Base
6. Attach parts to uprights as shown.
Note: The pulley assembly is on the opposite side of
rope cleat.
Flat Side
Upright
Top
Bottom
8-32 X 5/8” Flat Head Screw
Bottom
Top Rope Cleat
WARNING
THIS EQUIPMENT MUST BE STORED IN A SECURED, SHELTERED AREA WHEN NOT IN USE OR IN THE
THREAT OF HIGH WINDS. ANY WEATHER DAMAGE TO THIS EQUIPMENT WILL NOT BE COVERED
UNDER KWIK GOAL’S LIFETIME GUARANTEE. DO NOT LEAVE THIS EQUIPMENT UNATTENDED.
Pulley Assembly
1/4” Lock Nut
1/4” Flat Washer
Upright
Flat Side

NZ328 Rev. 9/18/18
Upright
Upright
Upright
Upright
Assembled Base with
Heavy Duty Anchor Bags
Upright
Upright
Upright
Upright
Assembled Base with
Heavy Duty Anchor Bags
7. Lay out uprights as shown and put rope through
pulleys on each upright. Tie a snap link to the end of
each rope as shown.
Assembled Base with
Heavy Duty Anchor Bags Upright
8. Lift each upright onto assembled weighted base,
while holding both ends of rope to keep it from
coming out of pulley.
WARNING
THIS EQUIPMENT MUST BE STORED IN A SECURED, SHELTERED AREA WHEN NOT IN USE OR IN THE
THREAT OF HIGH WINDS. ANY WEATHER DAMAGE TO THIS EQUIPMENT WILL NOT BE COVERED
UNDER KWIK GOAL’S LIFETIME GUARANTEE. DO NOT LEAVE THIS EQUIPMENT UNATTENDED.
Upright
Pulley
Rope

NZ328 Rev. 9/18/18
9. Attach 3/8” X 3” threaded stud to brace on
plate with threaded hole. With square nut &
stud, attach braces to bottom bar using
knob & 3/8” lock nut. NOTE: Tighten 3/8”
lock nuts only until flush with end of stud so
knob can turn. Loosen knob to slide brace
to hold upright and when upright is plumb
tighten knob to hold brace in place.
Net
10. Lay out net out as shown. Clip rope to net in 4 locations.
Knob
Bottom Bar
Upright
Bottom Bar
Square Nut & Stud
3/8” Nut
3/8” Lock Nut
3/8” Lock Washer
3/8” Flat Washer
3/8” X 3” Threaded Stud
Threaded Plate
Brace
Knob
Net
Snap Link
Rope
Top Corner Tag
Threaded Plate
Upright
3/8” X 3” Threaded Stud
Brace
WARNING
THIS EQUIPMENT MUST BE STORED IN A SECURED, SHELTERED AREA WHEN NOT IN USE OR IN THE
THREAT OF HIGH WINDS. ANY WEATHER DAMAGE TO THIS EQUIPMENT WILL NOT BE COVERED
UNDER KWIK GOAL’S LIFETIME GUARANTEE. DO NOT LEAVE THIS EQUIPMENT UNATTENDED.

Net
Upright
Net Holder
Net Holder
Net
Rope
Rope Cleat
Upright
Net Holder
Top Corner Tag
17”
17”
NZ328 Rev. 9/18/18
11. Starting at one end, hoist net and attach net holders to the perimeter rope of net approximately 17” from
the top corner. Then wrap net holder around upright and attach to the perimeter rope again 17” from the
first clip.
12. Hoist net up enough to attach the next net holder
and repeat step 11 until net is hoisted to the top of
upright. Repeat step 11 & 12 for other end
upright.
Net
WARNING
THIS EQUIPMENT MUST BE STORED IN A SECURED, SHELTERED AREA WHEN NOT IN USE OR IN THE
THREAT OF HIGH WINDS. ANY WEATHER DAMAGE TO THIS EQUIPMENT WILL NOT BE COVERED
UNDER KWIK GOAL’S LIFETIME GUARANTEE. DO NOT LEAVE THIS EQUIPMENT UNATTENDED.

NZ328 Rev. 9/18/18
13. Complete net raising by hoisting net on two center poles. To secure bottom of net, attach net to
bottom bar of backstop with net clips. Place perimeter rope of net in clip and put base of clip into
channel and turn 90 degrees to lock into place. Space net clips evenly throughout base, see below
for approximate spacing.
CAUTION: BE SURE THAT BACKSTOP IS PROPERLY ANCHORED BEFORE ATTEMPTING TO ATTACH
NET.
20”
Net Clip
Bottom Bar
Perimeter Rope
Net Clip
WARNING
THIS EQUIPMENT MUST BE STORED IN A SECURED, SHELTERED AREA WHEN NOT IN USE OR IN THE
THREAT OF HIGH WINDS. ANY WEATHER DAMAGE TO THIS EQUIPMENT WILL NOT BE COVERED
UNDER KWIK GOAL’S LIFETIME GUARANTEE. DO NOT LEAVE THIS EQUIPMENT UNATTENDED.

180 TO 90 180 TO 90
NZ328 Rev. 9/18/18
14. This unit can be set up to conform to irregular boundaries, such as arcs.
15. After first assembly this unit can be disassembled
without any tools. Loosening the knob allows
braces to slide in and out of bottom bar.
CAUTION: REMOVE NET AND UPRIGHT BEFORE
ADJUSTING ANGLES. DO NOT MOVE UNIT
WHEN FULLY ASSEMBLED THIS COULD CAUSE
INJURY OR DEATH.
OVER HEAD VIEW
Knob
Bottom Bar
WARNING
THIS EQUIPMENT MUST BE STORED IN A SECURED, SHELTERED AREA WHEN NOT IN USE OR IN THE
THREAT OF HIGH WINDS. ANY WEATHER DAMAGE TO THIS EQUIPMENT WILL NOT BE COVERED
UNDER KWIK GOAL’S LIFETIME GUARANTEE. DO NOT LEAVE THIS EQUIPMENT UNATTENDED.
°°°°
Go to kwikgoal.com for additional product information.