Kyocera KD135GX-LPU User manual

INSTALLATION MANUAL
FOR THE
OF
SOLAR PHOTOVOLTAIC POWER MODULES
Please read this manual carefully before installing the modules.
KYOCERA
6C-208590
1. INTRODUCTION
As the world leader in the development and application of
high technology ceramic/silica materials, Kyocera offers a
wide range of highly efficient and reliable crystalline silicon
solar photovoltaic (PV) power modules. Kyocera began to
extensively research PV technology in 1975 and
commenced manufacturing operations in 1978. Since then,
Kyocera has supplied millions of cells and modules
throughout the world. With years of experience and
state-of-the-art technology, Kyocera provides the highest
quality PV power modules in a range of sizes designed to
meet the requirements of the most demanding energy and
power users worldwide.
2. APPLICATIONS
KDxxxGX-LPx series modules are a reliable, virtually
maintenance-free direct current (DC) power source,
designed to operate at the highest level of efficiency.
KDxxxGX-LPx series modules are ideal for remote home,
water pumping, utility-tied, telecommunications and
many other applications either with or without using
storage batteries.
3. WARNINGS & SAFETY
PV modules generate electricity when exposed to light.
Arrays of many modules can cause lethal shock and
burn hazards. Only authorized and trained personnel
should have access to these modules. To reduce the risk
of electrical shock or burns, modules may be covered
with an opaque material during installation. Do not touch
live terminals with bare hands. Use insulated tools for
electrical connections. Do not use these modules for
solar concentration.
PERMIT
・ Before installing your PV system, contact local
authorities to determine the necessary permits,
installation and inspection requirements.
INSTALLATION AND OPERATION
・ Systems should be installed by qualified personnel only.
The system involves electricity, and can be dangerous if
the personnel are not familiar with the appropriate safety
procedures.
・ Do not step on the module.
・ Although KDxxxGX-LPx series modules are quite
durable, the glass can be broken (and the module will no
longer work properly) if it is dropped or hit by tools or
other objects.
・ The module frame is made of anodized aluminum, and
therefore corrosion can occur if the module is subject to
a salt-water environment and is in contact with another
type of metal (electrolytic corrosion). If required, PVC or
stainless steel washers can be placed between PV
module frame and support structure to prevent this type
of corrosion.
・ KDxxxGX-LPx series module frame(s) must be
attached to a support structure by one of the methods
described in Section 6, Installing KDxxxGX-LPx series
module(s).
・ Module support structures to be used to support
KDxxxGX-LPx series module(s) should be wind rated
and approved by the appropriate local and civil codes
prior to installation.
・ Do not expose the back of the module to direct sunlight
・ In Canada installation shall be in accordance with CSA
C22.1, Safety Standard for Electrical Installations,
Canadian Electrical Code, Part 1.
・ When handle the modules, DO NOT HOLD THEM BY
SUPPORTING ONLY ONE SIDE OF THE LONG
FRAME BECAUSE IT CAN CAUSE SEPARATION OF
THE GLASS AND FRAME.
CAUTION
FIRE RATING
・ In case of roof installation, PV module assembly shall be
mounted on a fire resistant roof covering rated for the
application. KDxxxGX-LPx series modules are
comprised of a glass front surface, polyethylene
terephthalate (PET) backsheet with a ClassC fire rating.
GROUNDING
・ Refer to “Grounding” section.
BATTERY
・ When PV modules are used to charge batteries, the
battery must be installed in a manner, which will ensure
the performance of the system and the safety of its users.
Follow the battery manufacturer’s safety guidelines
concerning installation, operation and maintenance
recommendations. In general, the battery (or battery
bank) should be kept away from people and animals.
Select a battery site that is protected from sunlight, rain,
snow, debris, and is well ventilated. Most batteries
generate hydrogen gas when charging, which can be
explosive. Do not light matches or create sparks near
the battery bank. When a battery is installed outdoors, it
should be placed in an insulated and ventilated battery
case specifically designed for this purpose.
4. SITE SELECTION
In most applications, KDxxxGX-LPx series modules should
be installed in a location where they will receive maximum
sunlight throughout the year. In the Northern Hemisphere,
KD135GX-LPU～KD245GX-LPB

the modules should typically face south, and in the
Southern Hemisphere, the modules should typically face
north. Modules facing 30 degrees away from true South (or
North) will lose approximately 10 to 15 percent of their
power output. If the module faces 60 degrees away from
true South (or North), the power loss will be 20 to 30 percent.
When choosing a site, avoid trees, buildings or obstructions,
which could cast shadows on PV modules especially during
the winter season when the arc of the sun is lowest over the
horizon.
5. MODULE TILT ANGLE
KDxxxGX-LPx series modules produce bigger power when
they are pointed directly at the sun.
For grid tie installations where the PV modules are attached
to a permanent structure, PV modules should be tilted at an
angle equal to the site's latitude. This will typically result in
the highest annual energy output.
6. INSTALLING KDxxxGX-LPx SERIES
MODULES
To install the module, use bolt and nut on installation holes
which are opened in the module frame and install the
module by following the instruction below.
The minimum spacing of 2” (50 mm) is required between PV
module and the mounting surface around the perimeter of
PV module. KDxxxGX-LPx series modules may be
installed in various applications utilizing a variety of support
structure options and attachment methods. For optimal
performance in all applications, clearance between the
module frame and the mounting surface is required to allow
cooler ambient air to circulate around the back of the
module and to avoid the module and / or wiring damage. A
minimum of .13” (3.2 mm) spacing must also be maintained
between module frames to allow for thermal expansion.
KDxxxGX-LPx series modules may be attached to a
support structure by the following methods. When installing
modules in snowy area, an appropriate countermeasure
has to be taken to prevent possible damages to the lower
side frame by slipping snow (e.g. attach supporting parts to
the lowest modules.). Any damage caused by snow or such
countermeasure is not covered under warranty.
BOLTING: Utilizing 5/16” or 8 mm steel hardware structure
through the existing .35” (9 mm) diameter mounting holes in
the module frame and then through KDxxxGX-LPx series
module mounting holes on the support structure. Tighten
the screws with adequate torque (usually 132 in-lb).
Support structure should have enough strength to keep the
mounting span. Refer to the Module Drawings for the
position of PV module mounting holes.
7. MODULE WIRING
KDxxxGX-LPx series modules come pre-wired with
terminals ready for most building attachments or free
standing installations. Each module has two #12 AWG type
PV-wire stranded sunlight resistant output cables each
terminated with Multi-Contactlocking connectors. The
positive (+) terminal has a male connector while the
negative (-) terminal has a female connector. The module
wiring is solely for series connections only, i.e. male (+) to
female (-) interconnections. Series and parallel connections
shall be made by use of two #10-14 AWG type PV-wire
stranded sunlight resistant and insulated for 90℃minimum
output cables with male and female Multi-Contactlocking
connectors.
NOTE: When making connections with Multi-Contact
connectors, make sure the array is disabled. DO NOT
MAKE CONNECTIONS WHILE UNDER LOAD.Module
output connections are marked “Do not disconnect under
load”.
NOTE: MAXIMUM SYSTEM VOLTAGE 600 VDC.
KDxxxGX-LPx series modules and most PV system
components have a maximum system voltage rating of 600
volts DC. Some grid feed in systems operate at or near this
voltage rating. Like other polycrystalline the PV modules,
the open circuit voltage of the KDxxxGX-LPx series
modules increases as the ambient temperature decreases.
Maximum system voltage is computed as the sum of the
open-circuit voltage of the series-connected PV modules for
the lowest expected ambient temperature. Refer to the
National Electrical Code Article 690-7(a) for determining the
maximum number of KDxxxGX-LPx series modules that
can be placed
in series. Temperature coefficients, specific
to the module of use, can be used to provide the most
accurate prediction of module voltage under temperature
extremes.
NOTE: Install the maximum number of series connection for
the KDxxxGX-LPx series modules so that the system
voltage is less than 600 V.
NOTE: Do not connect the modules in parallel without
maximum over current protection.
NOTE: The minimum diameter that the cable can be bent
for the KDxxxGX-LPx series modules is 1.93” (49mm).
NOTE: In normal conditions, PV modules may produce
larger current and / or voltage than reported in the standard
test conditions. Therefore, when voltage evaluations for
components, capacity of conductors, size of fuses, and size
of control systems connected to the module output are
determined, multiply the values of short- circuit current (Isc)
and open-circuit voltage (Voc) that are marked in
KDxxxGX-LPx series modules by the coefficient, 1.25.
NOTE: Refer to Section 690-8 of the National Electrical
Code for an additional multiplying factor of 125 percent (80
percent derating) which may be applicable.
8. GROUNDING
Before installation, contact the local code authorities to
determine the necessary grounding requirements. When
installing in US market, attach all PV module frames to an
earth ground in accordance with the National Electrical
Code (NEC) Article 250. Proper grounding is achieved by
connecting PV module frames and all metallic structural
members contiguously to one another using a suitable
grounding conductor. The grounding conductor shall be of
copper, copper alloy or another material suitable for use as
an electrical conductor per NEC. The grounding conductor
must then make a connection to earth using a suitable earth
grounding electrode. Ensure positive electrical contact
through the anodizing on the module frame extrusion by
utilizing one of the following methods. Attach the grounding
conductor:

(1)to one of the .35” (9mm) diameter holes marked “ground”
using 5/16” stainless steel hardware. Wrap conductor
around bolt. Tighten the screws with adequate torque
(usually 132 in-lb). Avoid direct contact of copper ground
conductor to aluminum frame.
(2)to a ground lug (manufacturer:ILSCO,model:GBL-4DBT).
Tighten the screws with adequate torque (usually 62
in-lb). Use #10-32 stainless steel hardware to attach the
lug to the module frame by the torque of 40 in-lb. A
stainless steel star washer, positioned between the lug
and the anodized surface of the frame, must be employed
to break through the anodized layer of the frame
extrusion and electrically connect the ground lug to the
conducting aluminum frame material.
As a general rule, avoid direct contact of copper or copper
alloy ground conductors with the aluminum module frame.
All ground bond securing hardware in contact with either the
aluminum module frame and / or copper or copper alloy
ground conductors must be stainless steel.
9. BLOCKING DIODES
In systems utilizing a battery, blocking diodes are typically
placed between the battery and PV module output to
prevent battery from discharging at night. KDxxxGX-LPx
series modules are made of polycrystalline cells with high
electrical “back flow” resistance to nighttime battery
discharging. As a result, KDxxxGX-LPx series modules do
not contain a blocking diode when shipped from the factory.
Most PV charge regulators and inverters incorporate
nighttime disconnect feature.
10. BYPASS DIODES
Partial shading of an individual module in a source circuit
string (i.e. two or more modules connected in series) can
cause a reverse voltage across the shaded cells within the
module. Module output current is then forced through the
shaded area by the remaining illuminated cells and other
PV modules in series with the partially shaded module(s).
The current forced through the shaded cells within PV
module (or modules) causes additional module heating and
severe loss of power. All KDxxxGX-LPxseries modules are
supplied with factory installed (non user serviceable)
bypass diodes.
The purpose of bypass diodes is to provide a low-resistance
current path around the shaded cells, thereby minimizing
PV module heating and array current losses.
PV modules employ bypass diodes that have:
・ Rated Average Forward Current [IF(AV)] Above
maximum system current at highest PV module
operating temperature.
・ Rated Repetitive Peak Reverse Voltage [VRRM] Above
maximum system voltage at lowest PV module
operating temperature.
11. MAINTENANCE
KDxxxGX-LPx series modules are designed for long life
and require very little maintenance. Under most weather
conditions, normal rainfall is sufficient to keep the module
glass surface clean. If dirt build-up becomes excessive,
clean the glass surface only with a soft cloth using mild
detergent and water. USE CAUTION WHEN CLEANING
THE BACK SURFACE OF PV MODULE TO AVOID
PENETRATING BACK SHEET. PV modules that are
mounted flat (0°tilt angle) should be cleaned more often,
as they will not "self clean" as effectively as modules
mounted at a 15°tilt or greater. Once a year, check the
general condition of the wiring and check to be sure that
mounting hardware is tight. Loose connections may result
in a damaged module or array.
KYOCERA Solar Group Sales Office
KYOCERA Corporation
Corporate Solar Energy Group
6 Takeda Tobadono-cho Fushimi-ku, Kyoto 612-8501, Japan
Phone: [phone]
Fax: [phone]
http://www.kyocera.com/
KYOCERA Solar, Inc.
7812 East Acoma Drive, Scottsdale, AZ 85260, U.S.A.
Phone: [phone] or 1-800-223-9580
Fax: [phone]
http://www.kyocerasolar.com/
KYOCERA Solar Pty Ltd.
Level 3, 6-10 Talavera Road, North Ryde NSW 2113, Australia
Phone: [phone]
Fax: [phone]
http://www.kyocerasolar.com.au/
KYOCERA Solar do Brasil Ltda.
Av. das Americas, 20007 –Bloco 2 – Salas (rooms) 105 to 108,
Rio de Janeiro, 22790-851, Brazil
Phone: [phone]
Fax: [phone]
http://www.kyocerasolar.com.br/
KYOCERA Fineceramics GmbH
Fritz-Mueller-Strasse 27, 73730 Esslingen, Germany
Phone: [phone]
Fax: [phone]
http://www.kyocerasolar.de/
KYOCERA Asia Pacific Pte. Ltd.
298 Tiong Bahru Road, #13-03/05 Central Plaza
168730 Singapore
Phone: [phone]
Fax: [phone]
http://www.kyocera.com.sg/
KYOCERA Asia Pacific Ltd.
Room 801-802, Tower 1, South Seas Centre,
75 Mody Road, Tsimshatsui East, Kowloon, Hong Kong
Phone: [phone]
Fax: [phone]
KYOCERA Asia Pacific Pte. Ltd. Taipei Branch
10 Fl., No.66, Nanking West Road, Taipei, Taiwan
Phone: [phone]
Fax: [phone]
KYOCERA (Tianjin) Sales ＆Trading Corporation
Room 1509, Tower A, Gemdale Plaza,No.91, Jianguo Road,
Chaoyang District, Beijing, 100022, China
Phone: [phone]
Fax: [phone]
http://www.kyocera.com.cn/
KYOCERA Korea Co., Ltd.
Diplomatic Center Room #406, 1376-1,
Seocho-2Dong, Seocho-Ku, Seoul, 137-072, Korea
Phone: [phone]
Fax: [phone]
http://www.kyocera.co.kr/
Nut
Spring washer
Flat washer
Star washer
Ground lug
Bolt
Aluminum
frame
Nut
Spring washer
Flat washer
Star washer
Ground lug
Bolt
Aluminum
frame
Nut
Spring washer
Flat washer
Ground conductor
Cup washer
Star washer
Aluminum frame
Flat washer
Bolt
Nut
Spring washer
Flat washer
Ground conductor
Cup washer
Star washer
Aluminum frame
Flat washer
Bolt

12. SPECIFICATIONS
・ Under certain conditions, a photovoltaic module may produce more voltage and current than reported at Standard Test
Conditions (STC). Refer to Section 690 of the National Electrical Code for guidance in series string sizing and choosing
overcurrent protection.
Kyocera KDxxxGX-LPx Series Module Specification
Electrical Characteristics: @ STC
Module Type KD135GX-LPU KD185GX-LPU KD205GX-LPU KD210GX-LPU KD215GX-LPU KD225GX-LPB KD230GX-LPB KD235GX-LPB KD240GX-LPB KD245GX-LPB
Pmax(W) 135 185 205 210 215 225 230 235 240 245
Voc(V) 22.1 29.5 33.2 33.2 33.2 36.9 36.9 36.9 36.9 36.9
Isc(A) 8.37 8.58 8.36 8.58 8.78 8.18 8.36 8.55 8.59 8.91
Vpm(V) 17.7 23.6 26.6 26.6 26.6 29.8 29.8 29.8 29.8 29.8
Ipm(A) 7.63 7.84 7.71 7.90 8.09 7.55 7.72 7.89 8.06 8.23
Factory installed Bypass Diode
(QTY) YES (2pcs) YES (3pcs)
Series Fuse
Rating 15
Thermal Characteristics: Temp. Coefficient
Voc (V/°C) -0.80×10 -1 -1.06×10-1 -1.20×10-1 -1.20×10-1 -1.20×10-1 -1.33×10
-1 -1.33×10 -1 -1.33×10 -1 -1.33×10 -1 -1.33×10 -1
I sc (A/°C) 5.02×10-3 5.15×10-3 5.02×10-3 5.15×10-3 5.27×10-3 4.91×10-3 5.02×10-3 5.13×10-3 5.15×10-3 5.35×10-3
Vpm (V/℃) -0.92×10-1 -1.23×10-1 -1.38×10-1 -1.39×10-1 -1.39×10-1 -1.53×10-1 -1.53×10-1 -1.54×10-1 -1.54×10-1 -1.55×10-1
Physical Characteristics:
Length 59.06”
(1500mm) 52.68” (1338mm) 59.06” (1500mm) 59.06” (1500mm) 59.06” (1500mm) 65.43” (1662mm) 65.43” (1662mm) 65.43” (1662mm) 65.43” (1662mm) 65.43” (1662mm)
Width 26.30”
(668mm) 38.98” (990mm) 38.98” (990mm) 38.98” (990mm) 38.98” (990mm) 38.98” (990mm) 38.98” (990mm) 38.98” (990mm) 38.98” (990mm) 38.98” (990mm)
Depth 1.81” (46mm) 1.81” (46mm) 1.81” (46mm) 1.81” (46mm) 1.81” (46mm) 1.81” (46mm) 1.81” (46mm) 1.81” (46mm) 1.81” (46mm) 1.81” (46mm)
Weight 27.6 lb
(12.5kg) 35.3 lb (16.0kg) 39.7 lb (18.0 kg) 39.7 lb (18.0 kg) 39.7 lb (18.0 kg) 46.3 lb (21.0 kg) 46.3 lb (21.0 kg) 46.3 lb (21.0 kg) 46.3 lb (21.0 kg) 46.3 lb (21.0 kg)
Mounting
Hole Diameter .35”(9mm) Quantity 4pcs
Grounding
Hole Diameter .35”(9mm) Quantity 4pcs
Application
Class Class A
NOTES
(1) The electrical characteristics are within +/-5% of the installed values of Pmax and within +/-10% of the installed values of Isc and Voc
under standard test conditions (irradiance of 1000W/m2, AM 1.5 spectrum, and a cell temperature of 25 deg C).
(2) See module specification sheet for most recent electrical characteristics.
(3) See module drawing for mounting grounding holes locations.
KD185GX-LPU
KD135GX-LPU
MODULE TYPE
32.48"
10.10"37.99"
38.89"
52.68" .49"
25.31"
59.06" 26.30"
10.96"
.49" 37.13"
DIM.C
MODULE DIMENSIONS
DIM.A DIM.B
DIM.EDIM.D DIM.F
.35"
.35"
DIM.G
43.31"
DIM.F
37.13"
37.99"
DIM.C
37.99"
MODULE DIMENSIONS
38.98"
DIM.B
38.98"
65.43"
DIM.A
59.06"
.49"
.49"
DIM.D
11.06"
DIM.E
10.96"
DIM.G
.35"
.35"
MODULE TYPE
KD205GX-LPU,KD210GX-LPU,KD215GX-LPU
KD225GX-LPB,KD230GX-LPB,KD235GX-LPB,KD240GX-LPB,KD245GX-LPB
43.3"
WIRE
LENGTH
"D"
"D"
“A”
"F" "E"
39.8"
WIRE
a
LENGTH
“B”
“C” b
b
KD135GX-LPU
LENGTH
33.1"
WIRE
MARKED
GROUND HOLE
a
φ“G”
"E"
“A”
"F"
[TYP.]
KD185GX-LPU
"C"
“B”
WIRE
33.1"
LENGTH
0.41"
b
b
aa
40.6"
WIRE
LENGTH
LENGTH
WIRE
35.4"
“A”
"D"
"E""F"
0.47"
“C”
“B”
b
b
KD205GX-LPU
KD210GX-LPU
KD215GX-LPU
LENGTH
"B"
"C"
GROUND HOLE
φ“G”
aa
MARKED
[TYP.]
"F"
"A"
"D"
"E"
WIRE
37.8"
a
LENGTH
b
b
46.9"
WIRE
a
0.79"
SECTION a-a
1.81"
SECTION b-b
1.18"
0.47"
1.81"
KD225GX-LPB
KD230GX-LPB
KD235GX-LPB
KD240GX-LPB
KD245GX-LPB