Kyocera C8100DN - Color Laser Printer User manual

Installation Guide
Clearance
• Temperature: 10 to 32.5 °C (50 to 90.5 °F) However, the humidity should be 70 % or less
when the temperature is 32.5 °C (90.5 °F)
• Humidity: 15 to 80 %RH However, the temperature should be 30 °C (86 °F) or less when the
humidity is 80 %
• Power Supply: 120 V AC, 60 Hz, 12.0 A / 220 to 240 V AC, 50/60 Hz, 7.2 A
Unpacking
Pull out the paper cassettes 1 and 2.
FS-C8100DN
Environment
CAUTION: Be sure to provide enough space around the printer. Prolonged use without
sufficient clearance may cause heat to build up inside the printer, resulting in fire.
300 mm (11-13/16") 300 mm (11-13/16") 100 mm (3-15/16") 1000 mm (39-3/8")
Checking Shipped Components Removing the Lift Plate
Stoppers
Shipped components
CD-ROMs Manuals and Other Printed
Matters
Printer
Power Cord
Toner Containers (4) Waste Toner Box
Paper Size Sheets (4)
Lift Plate Stopper
Remove the lift plate stopper and
attach it to the storage location.
Installing the Toner Container and Waste Toner Box
Open the front cover. Lightly tap the upper part of the toner
container 10 times or more.
Thoroughly shake the toner container
10 times or more.
Open the cap of the waste toner box
and install the waste toner box.
Turn the lock lever to the left.
Install the other toner containers in the
same way.
Install the toner container.
Close the front cover.
CAUTION: When moving the printer, pull out the two carrying handles on the left side, and move with the carrying handles on the right
side by inserting hands in the two spaces provided to get a firm grasp. The printer must be carried by four persons or more.
3
12
1 432
678
1
2
Lock Lever
5Push the front of the toner container
firmly, until you hear a click.
Remove the tapes, spacers, and desiccant.

Pull out the paper cassette.
Paper Width Guides
Loading Paper
Fan the paper, then tap it on a level
surface to avoid media jams or skewed
printing.
Adjust the paper length guide to fit the
paper size.
Adjust the paper width guides to fit the
paper size.
Paper Length Guide
Load paper in the cassette, with side to
be printed downward.
For details on paper usable with this
printer, refer to the Operation Guide.
Important: Do not exceed the upper limit
of the tray. Otherwise, it may cause paper
jams.
Set the supplied paper size sheet at
the front of the paper cassette.
Push the paper cassette back until it
stops.
Paper Size SheetLimit Mark
4
2
5
3
6
1
7
4
Connect the power cord to the printer
and the other end into a power outlet.
Turn the power switch off (O). Connect the printer to the PC or your
network device. (These cables are sold
separately.)
Connecting Cables
Network Interface
USB Interface
Parallel Interface
5
132
Test Printing
Turn the power switch on (|).
Press Sor Trepeatedly until Print Status Page appears.
Press [OK]. A blinking question mark (?) appears.
Press [OK] again. The printer prints a status page.
6
3
1
4
5
6
© 2006 by KYOCERA MITA Corporation All rights reserved. 2-28, 1-Chome, Tamatsukuri, Chuo-ku, Osaka 540-8585, Japan Printed in Japan 302HP56030 Rev.1.0 2006.10
Refer to the Operation Guide to install the printer driver and setting network parameters.
Press [MENU].
2Wait until the message display indicates Ready.