Kyoritsu Electrical Instruments Works, Ltd. KEW2040 User manual

INSTRUCTIONMANUAL
DIGITALCLAMPMETER
KEWSNAP
SERIES
KEW2040  600AACOnlyType
KEW2055
1000AAC/DCType
１．Features
● Designedtomeetinternationalsafetystandards.
IEC61010-1.IEC61010-031:2002&IEC61010-2-032
MeasurementCategory(CAT.)IV600V
PollutionDegree2
● Double molded main body provides comfortable

singlehandedgrip
●
DataHoldFunction
● LCD Backlight function to facilitate working at
dimlylitsituations.(KEW2055only)
● RELfunctiontoindicatemeasurementvariation.
(Current,voltage,Resistancemeasurement)
● MIN/MAX function enables easy reading of min &
maxvalueduringmeasurement.
● WithContinuity&DiodeCheckFunction
● NCV （ Non Contact Voltage ） Function for wiring
check.
● 600Vinputprotection.
● Sleepfunctiontoextendbatterylife.
● WithBarGraph,6039counts
2.SafetyWarnings
This instrument has been designed, manufactured and
testedaccordingtoIEC61010:Safetyrequirementsfor
ElectronicMeasuringapparatus,anddeliveredin
the best condition after passed the inspection. This
instructionmanualcontainswarningsandsafety
rules which must be observed by the user to ensure
safeoperation of the instrument and retain itin safe
condition.
Therefore, read through these operating instructions
beforeusingtheinstrument.
WARNING
● Read through and understand the instructions
containedinthismanualbeforeusingthe
instrument.
● Keepthemanualathandtoenablequick
referencewhenevernecessary.
● Theinstrumentistobeusedonlyinitsintended
applications.
● Understand and followall thesafety
instructionscontainedinthemanual.
● It is essential that the above instructions are
adheredto.
● Failure to follow the above instructions may
causeinjury,instrumentdamageand/ordamage
toequipmentundertest.
Thesymbol indicated ontheinstrumentmeansthat
theusermustrefertotherelatedpartsinthemanual
forsafeoperationoftheinstrument.Itisessential to
read the instructions wherever the  symbol appears
inthemanual.

DANGERisreserved forconditionsand actions
thatarelikelytocauseseriousorfatalinjury.

WARNINGisreservedforconditionsandactions
thatcancauseseriousorfatalinjury.

CAUTIONisreservedforconditionsandactions
thatcancauseinjuryorinstrumentdamage.
●
Marks listed in the table below are used on this
instrument.
Usermustrefertothemanual.
Instrumentwithdoubleorreinforcedinsulation
Indicates that this instrument can clamp on
bare conductors when measuring a voltage
corresponding to the applicable measurement
category,whichismarkednexttothissymbol.
AC
 DC
AC&DC
DANGER
● Nevermakemeasurementona circuitin which
voltageoverAC600Vexists.
● Do not attempt to make measurement in the
presence of flammable gasses. Otherwise, the
use of theinstrument may causesparking,
whichcanleadtoanexplosion.
● Transformerjaw tipsaredesignednot to short
the circuit under test. If equipment under test
has exposed conductive parts, however, extra
precaution should be taken to minimize the
possibilityofshorting.
● Never attemptto usethe instrumentifits
surfaceoryourhandiswet.
● Donotexceedthemaximumallowableinputof
anymeasuringrange.
● Neveropenthe Batterycover duringa
measurement.
●  Theinstrumentistobeusedonlyinitsintended
applications or conditions. Otherwise, safety
functions equipped with the instrument doesn
 t
work,andinstrumentdamageorseriouspersonal
injurymaybecaused.
WARNING
● Never attempt to make measurement if any
abnormal conditions, suchas brokencase
and exposed metal parts are found on the
instrument.
●
Do not rotate the Function Switch while the
testleadsarebeingconnected.
● Do not install substitute parts or make any
modification to the instrument. For repair or
re-calibration, return the instrument to your
localdistributorfromwhereitwaspurchased.
● Do nottryto replacethe batteriesif the
surfaceoftheinstrumentiswet.
● Disconnect all the cords and cables from the
objectunder testandpowerofftheinstrument
before opening the Battery Cover for Battery
replacement.
● Verify properoperation ona known source
before use or taking action as a result of the
indicationoftheinstrument.
● Use appropriate personal protective equipment
suchas insulatinggloves,Insulatingboots,and
safetyglasses.

CAUTION
● Set theFunction Switchto anappropriate
positionbeforestartingmeasurement.
● Firmlyinsertthetestleads.
● Disconnect the test leads from the instrument
forcurrentmeasurement.
● Donotexposetheinstrumenttothedirect sun,
hightemperatureandhumidityordewfall.
● Altitude 2000m or less. Appropriate operating
temperatureiswithin0
℃ and40 ℃ .
● Thisinstrumentisn  tdust&waterproofed.Keep
awayfromdustandwater.
● Be sure to power off the instrument after use.
When the instrument will not be in use for a
longperiod, place it in storage afterremoving
thebatteries.
● Useacloth dippedin wateror neutral
detergent for cleaning the instrument. Do not
useabrasivesorsolvents.
Measurementcategories (Over-voltagecategories)
To ensure safe operation of measuring instruments,
IEC61010 establishes safetystandards for various
electrical environments, categorizedas CAT.Ito
CAT.IV, and called measurement categories. Higher-
numbered categories correspondto electrical
environments with greatermomentary energy,
so a measuringinstrument designedfor CAT.III
environments can endure greater momentary energy
thanonedesignedforCAT.II.
CA T.Ⅰ :Secondaryelectrical circuitsconnectedtoan
ACelectricaloutletthroughatransformeror
similardevice.
CAT.Ⅱ :Primaryelectricalcircuits ofequipment
connected to an AC electrical outlet by a
powercord.
CA T.Ⅲ :Primary electrical circuits of the equipment
connected directly to the distribution panel,
and feeders from the distribution panel to
outlets.
CAT.Ⅳ :Thecircuitfrom theservice dropto the
service entrance, and to the power meter
and primary over current protection device
(distributionpanel).
3.Specification
3-1.Measuringrange&accuracy
(accuracyguaranteedat23 ℃± 5 ℃ .humidity45 〜 85%)
ACCurrent600A,1000AFunction
Function Measuring
Range
Accuracy
KEW2040 KEW2055
600A0-600.0A
± 1.5%rdg ± 5dgt
(50/60Hz)
± 3.5%rdg ± 8dgt
(40-400Hz)
± 1.5%rdg ± 5dgt
(50/60Hz)
± 3.5%rdg ± 8dgt
(40-400Hz)
1000A0-1000A N/A
DCCurrent600A,1000AFunction
Function Measuring
Range
Accuracy
KEW2040 KEW2055
600A
0-600.0A N/A
± 1.5%rdg ± 5dgt
1000A 0-1000A N/A
ACVoltageFunction

（ Auto-ranging,Inputimpedance:approx.10M Ω）
Range Measuring
Range
Accuracy
KEW2040 KEW2055
6/60/600V1-600.0V
± 1.3%rdg ± 4dgt(50/60Hz)
± 3.0%rdg ± 5dgt(40 〜 400Hz)
DCVoltageFunction

（ Auto-ranging,Inputimpedance:approx.10M Ω）
Range Measuring
Range
Accuracy
KEW2040 KEW2055
600mV/6/
60/600V0-600.0V
± 1.0%rdg ± 3dgt
Resistance （ Continuity/DiodeCheck ） Function
Range Measuring
Range
Accuracy
KEW2040 KEW2055
600
Ω /6k/
60k/600k
Ω
6M Ω
0-6M Ω ± 1.0%rdg ± 5dgt
60M Ω
6.00M-
60.00M
Ω
± 5%rdg ± 8dgt
ContBuzzer 0-600.0 Ω Buzzersoundsat100 Ω orless
Diode Testvoltage:0-2V
Frequency/ DUTY Function （ Auto-ranging for
Frequency
）
Range Measuring
Range
Accuracy
KEW2040 KEW2055
ACA 40Hz
− 400Hz
± 0.5%rdg ± 5dgt
ACV 1Hz 〜 10kHz
0.1-99.9%
(Pulsewidth/Pulseperiod)
± 2.5%rdg ± 5dgt
Note:Measurableinputsare:40Vrms@ACVor
60Arms@AC600A,350A@AC1000ARange
3-2.GeneralSpecification
● Modeofoperation : Δ ∑mode
● Display  :max.6039counts

(Frequency:9999)&Bargraph
●  Over-range indication : "OL" displayed when exceeding
the measuring range. (except for AC/DCV and 1000A
Function)
● Rangeswitching :
Auto-ranging/Voltage,ResistanceRange
Singlerange/Continuity,Diodecheckand DUTY
● Samplerate :threetimespersecond
● Functionalconstruction:
OFF/ACA/ACV/DCV/ Ω KEW2040
OFF/ACA/DCA/ACV/DCV/ Ω KEW2055
● Keys  :
SELECT(AC/DCswitching&/ Ω / / ),REL Δ ,
Hz/DUTY,MIN/MAX,HOLD/BackLight(KEW2055)
● Powersource :DC3V/R03(UM-4)x2pcs
● Lowbatterywarning : " "markisdisplayedat
  2.4V ± 0.15Vorless.
●  Temperature & humidity : 23 ℃± 5 ℃ , relative humidity

accuracyguaranteed85%orless(nocondensation)
● Operatingtemperature:0 〜 40 ℃ ,relativehumidity
&humidityrange85%orless(nocondensation)
● Storagetemperature :-20 〜 60 ℃ ,relativehumidity 
&humidityrange85%orless(nocondensation)
● Currentconsumption:approx.12mA
● SleepFunction:Automaticallypoweredoffinabout
15minafterthelastFunctionswitchoperation.
Press any key or rotate the Function Switch from
OFFtoanypositiontoexitfromtheSleepstate.
● ApplicableStandards
IEC61010-1:2001
MeasurementCAT.IV600VPollutiondegree2
IEC61010-031:2002,IEC61010-2-032
EMC ： EN61326
・ EN55022
・ EN61000-4-2(performancecriterionB)
・ EN61000-4-3(performancecriterionB)
● OverloadProtection
CurrentRange :720AAC/10sec@KEW2040

1200AAC/DC/10sec@KEW2055
VoltageRange :720VAC/DC/10sec
ResistanceRange :600VAC/DC/10sec
● WithstandVoltage
6880VAC （ TRMS50/60Hz ） /5sec
(betweenJawsandelectricalcircuit/betweeninternal 
circuitandenclosure)
● InsulationResistance:10M Ω ormore/1000V
（ betweenelectricalcircuitandenclosure ）
● Conductorsize
KEW2040:approx.33mm
KEW2055:approx.40mm
● Dimension
approx.254(L) × 82(W) × 36(D)mm/KEW2055
approx.243(L) × 77(W) × 36(D)mm/KEW2040
● Weight:approx.:300g@KEW2040
:310g@KEW2055
● Accessories
TestLeads Model7066/1set
BatteryR03 （ UM-4 ） /2pcs
InstructionmanualEnglish,Japanese/1pce
CarriyngCaseModel9094/1pcs
3-3.FunctionKeys
The" ● "markshowsavailablefunctionateachRange.
DCCurrentMeasurement(KEW2055only)
HOLD SELECT ZERO Hz/
DUTY MAX/ MIN
ACA
●●●●●
ACV ● - ●●●
DCA ●●● - ●
DCV ● - ● - ●
Ω●●●
- ●
- ● ---
- ● ---
4.Preparationformeasurement
4-1.CheckingBatteryVoltage
Set the Function Switch to any position other than
"
OFF ". Whenthedisplayisclear without " BATT " mark,
showing, battery voltage is enough. When the display
is blank or
 " BATT "  mark is indicated, replace the
batteriesaccordingtoSection7,BatteryReplacement.
CAUTION
The Sleep featureautomatically powersthe
instrument off in about 15 min after the last
switch or key operation. Therefore, the display
may be blank even with the Function Switch set
to a position other than  "
OFF ". To operate the
instrument in this case, turn the switch back to
the  "
OFF "  position, then to any other position,
orpressanykey.Replacethebatteriesifnothing
wasdisplayedafteraboveoperations.
4-2.CheckingSwitchSetting&Operation
Confirm the Function Switch is set to the correct
position, the instrumentis setto thecorrect
measurementmode,
and the Data hold function is disabled. Otherwise,
desiredmeasurementcannotbemade.
5.Measurement
5-1.ACCurrentMeasurement
DANGER
● Never make measurement on a circuit in which
voltage over AC600V exists to avoid getting
electricalshock.
● Transformer jaw tips are designed not to short
the circuit under test. If equipment under test
has exposed conductive parts, however, extra
precaution should betaken tominimize the
possibilityofshorting.
● Donotmakemeasurement withthe Battery
Coverremoved.
● Disconnectthetestleadsfromtheinstrumentfor
currentmeasurement.
(1)SettheFunction Switchto "
600A " or " 1000A "
position.(onKEW2040,only"600A"isavailable)
AChasbeenselectedbydefault;presstheSELECT
key, when DC has been selected, to change it to
AC.ACmarkisdisplayedattheupperleftonthe
display.(KEW2055only)
(2)Press the trigger to open the transformer jaws
andclampthemontotheoneconductorundertest,
then take the reading on the display. Pressing the
"
Hz/DUTY "Keyswitchestheindicationinfollowing
sequence.
ACCurrent  ⇨  Hz  ⇨  DUTY
Hz/DUTY  Function requires 60A or more at AC600A
Rangeand350AormoreatAC1000Arange.
CAUTION
● MaxconductorsizeforKEW2040isapproxdia.
33mm and for KEW2055 is approx dia. 40mm.
During current measurement, keep the trans
former jaws fully closed. Other wise, accurate
measurementscannotbetaken.
5-2.DCCurrentMeasurement(KEW2055only)
DANGER
● Nevermakemeasurementonacircuitinwhich
voltage over DC600V exists to avoid getting
electricalshock.
● Do not make measurement with the Battery
Coverremoved.
(1)SettheFunction Switchto "
600A " or " 1000A "
position. AC has been selected by default; press
the SELECT  key, when AC has been selected, to
changeittoDC.

DC mark isdisplayed atthe upperleft onthe
Transformer
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]

5-4.DCVoltageMeasurement
DANGER
● Nevermakemeasurementonacircuitinwhich
voltage over DC600V exists to avoid getting
electricalshock.
● Do not make measurement with the Battery
Coverremoved.
●

Keep your fingers behind the barrier on the
instrumentduringmeasurement.
(1)SettheFunctionSwitchto"
DCV "position.
(2)ConnecttheredtestleadtoV/
Ω terminalandthe
blacktestleadtoCOMterminal.
(3)Connectthered andblack testleads tothe
positive (+)and negative (-) sides of the circuit
under test respectively. Take the reading on the
display. If the connection is reversed, the display
indicatesthe"-"mark.
5-5.Resistance/Cont/DiodeMeasurement
DANGER
● Neverusetheinstrumentonanenergizedcircuit.
● Do not make measurement with the Battery
Coverremoved.
Resistance
(1)SettheFunctionSwitchto " Ω/ Cont/ Diode "
position.
(2)ConnecttheredtestleadtoV/
Ω terminalandthe
black test lead to COM terminal. Confirm "OL" is
indicatedon thedisplay,andthenshort-circuit the
tipsoftestleadstomaketheindicationzero.
(3)Connect the test leads to the both ends of the
resistorundertest.
(4)Takethereadingonthedisplay.
CAUTION
●

Evenifshortthetestleadtips,indicatedvalue
may not be zero. But this is because of the
resistanceoftestleadsandnotafailure.
● Whentestleadsareopen,"OL"isindicatedon
thedisplay.
Continuity
(1)SettheFunctionSwitchto " Ω/ Cont/ Diode "
position. "
Ω "  has been selected by default; press
theSELECTkeytochangeitto"
Continuity ".
Resistance⇨Cont⇨Diode
(2)ConnecttheredtestleadtoV/ Ω terminalandthe
black test lead to COM terminal. Confirm "
OL " is
indicated on the display and short-circuit the tips
of test leads. Indication should become zero and
buzzersounds.
(3)Connect the test leads to the both ends of the
conductor under test. The buzzer sounds, if the
resistanceundertestis100
Ω orless.
Diode
(1)Set theFunctionSwitch to" Ω/ Cont/ Diode "
position. "
Ω " has been selected by default; press
theSELECTkeytochangeitto"
Diode "
Resistance⇨Cont⇨Diode
(2)ConnecttheredtestleadtoV/ Ω terminalandthe
blacktestleadtoCOMterminal.
(3)ConnecttheredandblacktestleadstotheAnode
and Cathode of the diode under test respectively.
Takethereadingonthedisplay.Iftheconnection
isreversed,thedisplayindicates"
OL ".
CAUTION
● Someofdiodescannot betested.Indicationon
thedisplay willbe"OL".
 (Zenerdiode, LEDand
soon)
6.Otherfunctions
6-1.SleepFunction
(1)This is a function to prevent the instrument from
beingleftpoweredoninordertoconservebattery
life.

This function causesthe instrumentto enter
Sleep mode about15 minutesafter thelast
key operation. To exit the Sleep mode, turn the
Functionswitchto"
OFF ",thentoanyotherposition,
orpressanyKey.
(2)SleepFunctionisdisabledwhen;MIN/MAX
Function is selected. Continuous measurement is
made with the Sleep Function being disabled. To
activate Sleep Function again, disable the MIN/
MAXFunction.
CAUTION
● The instrumentconsumes smallamount of
battery power inthe Sleepmode. Setthe
FunctionSwitchtotheOFFpositionafteruse.
6-2.HOLDKey
(1)DataHoldFunction
This is a function to freeze the measured value
onthedisplay.Pressthe"HOLD"keytofreeze the
reading.
The reading will be held regardless of subsequent
variationininput."
H "isindicatedontheupperleft
cornerofthedisplay whilethe instrumentisinthe
DataHoldmode.ToexitDataHoldmode,pressthe
"HOLD"keyagain.
CAUTION
● Heldreadings arereleased whenSleep
Functionisactivatedwhiletheinstrumentisin
theDataHoldmode.
(2)BacklightON/OFF(KEW2055only)
PressingtheHOLDkey2secormorelightsupthe
Backlight. Pressing the HOLD key 2 sec or more
againturnsofftheBacklight.
6-3.NCVFunction
Red LED on the upper area on the Panel lights up
at all functions except for OFF when electric field
exceeding 100V is detected by the sensor installed in
theJaws.
It indicates apresence of
voltageinanelectricalcircuit
or equipment without touching
them.
NCV Sensor candetect
electrical field only from the
directionindicatedintheright
figure.
Put the fixedelement (left
side) closer to the conductor
undertest.
Detection against in-wall
outletisimpossible.
DANGER
●

The LED may not light up due to installation
condition of electrical circuit or equipment.
Never touch the circuit under test to avoid
possible danger evenif theLED forNCV
doesn
 tlightup.
●

CheckthefunctionalityofLEDonawell-known
power supply prior to measurement. When the
LEDdoesn
 tlightup,donotmakemeasurement.
● NCVindicationisaffectedbyexternalvoltage,
howtoholdorplacetheinstrument.
6-4.MIN/MAXFunction
CAUTION
● SELECT, ZERO, Hz/DUTY keys are disabled
whileMIN/MAXFunctionisbeingactivated.
(1)
AC/DCCurrentRange (AC600AonlyonKEW2040)
Pressing the MIN/MAX Key at 600A & 1000A
Function enables min or max value measurement.
PresstheMIN/MAXKeytoselectMAXorMIN.The
maxormin value withinmeasuringrangeisbeing
held until this function is disabled. "MIN" or "MAX"
is indicated on the display while this function is
being activated. To disable this function, press
down the MIN/MAX Key at least 2 sec or change
functions.
(2)
AC/DCVoltageRange 
CAUTION
● Pressing the MIN/MAX Key without applying
voltagedisables theAuto-rangingfunctionand
fixes the Range to 6V. Connect the test leads
tothecircuitundertestandpresstheMIN/MAX
Key after an appropriate range is selected by
Auto-rangingfunction.
Pressing the MIN/MAX Key enables min or max value
measurement. Press the MIN/MAX Key to select MAX
orMIN.Themaxorminvaluewithinmeasuringrange
is being held until this function is disabled. "MIN" or
"MAX"isindicatedonthedisplaywhilethisfunctionis
beingactivated.
Todisablethisfunction,pressdowntheMIN/MAXKey
atleast2secorchangefunctions.
6-5.ZEROFunction
CAUTION
●

MIN/MAX,PEAKkeysaredisabledwhileZERO
Functionisbeingactivated.
ZeroAdjustmentFunctionat Current Range "
Δ "mark
istobeindicatedattheupperrightonthedisplaywhile
ZEROfunctionisbeingoperated.Indicationofrelative
value at Current, Voltage, Resistance: Pressing the
ZERO Key indicates REL (relative value) Press the
ZERO Key to save the initial value at the start of
measurementasareferencevalue.Thenthedifference
betweenthelatermeasuredvalues and the reference
valueisindicatedonthedisplay.
The Auto-ranging function is disabled, while this
functionisbeing activated, andtheRangeisfixed to
theRangeselectedatthestartofmeasurement.
Relativevalueisindicatedwithinfollowingranges.
（ Measuringrange ）
=(Full-scalevalueatthefixedRange)‒(Initialvalue)
Todisablethisfunction,pressdowntheMIN/MAXKey
atleast2secorchangefunctions.
6-6.Over-flowindication
When the input exceeds the measuring range at each
FunctionotherthanVoltageand1000ARange,"OL"or
"-OL"isindicatedonthedisplay.
7.BatteryReplacement
WARNING
●

MIN/MAX,PEAKkeys are disabledwhileZERO
Functionisbeingactivated.
CAUTION
●

Donotmixoldandnewbatteries.
●

Installbatteriesincorrectpolarityasindicated
intheBatteryCompartment.
Replace the batterieswhen aLow Battery
Voltage warning "BATT" mark is indicated on the
display. Note that when the battery is completely
exhausted,thedisplayblankswithout"
BATT "mark
shown.
(1)SettheFunctionSwitchto"OFF"position.
(2)Unscrew and remove the Battery Compartment
Coveronthebottomoftheinstrument.
(3)Replace the batteries observing correct polarity.
UsenewR03(AAA)orLR03/1.5Vbatteries.
(4)Install the Battery Compartment and tighten the
screws.
display.
(2)With thetransformerjaws closedand without
clamping them ontothe conductor,press the
"
ZERO " key to zero adjust the display. (mark is
displayedattheupperrightonthedisplay.)
(3)Pressthetriggertoopenthetransformerjawsand
clampthemontotheoneconductor undertest,the
conductorshouldbeatthecenterofthejaws,then
takethereadingonthedisplay.
(4)Setthe Function Switch toanappropriateposition
accordingtocurrentundertest.
(5)Pressing the  "
ZERO "  key again releases  " ZERO "
function. (mark at the upper right on the display
disappears.)
CAUTION
● When the current flows from the upside (the
displayside)totheundersideoftheinstrument,
thepolarity ofthereading ispositiveandvice
versa.
5-3.ACVoltageMeasurement
DANGER
● Nevermakemeasurementonacircuitinwhich
voltage over AC600V exists to avoid getting
electricalshock.
● Do not make measurement with the Battery
Coverremoved.
● Keep your fingers behind the barrier on the
instrumentduringmeasurement.
(1)SettheFunctionSwitchto"
ACV "position.
(2)ConnecttheredtestleadtoV/
Ω terminalandthe
blacktestleadtoCOMterminal.
(3)Connect the test leads to the circuit under test.
Take the readingon thedisplay. Pressingthe
"
Hz/DUTY " key while readingis indicatedon
the display switches the indication in following
sequence.
ACVoltage⇨Hz⇨DUTY
CAUTION
● Hz/DUTYFunctionrequiresAC40Vorhigher.
● To measure a frequency, measure the voltage
ontheelectricalcircuitinadvance.
● Then pressthe Hz/DUTYkey toenterinto
frequencymeasurement.
● Readings offrequencymay fluctuateorbe
influencedundernoisyenvironment.
Anode
Cathode
92-1801B06-05
8.Maintenance
● Cleaning
Use a cloth dipped in water or neutral detergent for
cleaningtheinstrument.
Donotuseabrasivesorsolvents.Otherwise,instrument
getdamaged,deformedordiscolored.
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]