La Crosse Technology 616A-1413 User manual

SET UP GUIDE
MODEL NUMBER 616A-1413 | 616-30357
5-in-1
* projection alarm
* 5w wireless charger
* usb-a-charging port
* usb-c-charging port
* temperature/humidity
Smart Watch, Phone, and Earbuds pictured are not included.
2.0
projection alarm clock
5W

Table of Contents
BASICS
APPENDIX
Initial Setup
Buttons
LCD Display
Accessories & Ports
LCD Display Brightness
Auto-Dim Settings
Display Modes
Display Mode Options
Specifications
Warranty
Recycling & Disposal
Cautions/Statements
Trademarks & Warning
Use the +/- buttons on
the top of the clock to
adjust the values.
02
Initial Setup
Power Up
Insert the 5V Power Adapter into an outlet, and then plug it into the Power Jack
on the bottom of the alarm clock. Next, remove the Insulation Tab from the
Clock’s Battery Compartment.
A greeting will appear on the LCD and the clock will then automatically move
into the Settings Menu.
You may exit the Settings
Menu at any time by
pressing the SNOOZE/
BACKLIGHT button.
02
03
04
04
05
05
06
06
18
19
19
19-21
21
SUPPORT
Support Information
Stay in Touch
22
22
ADD-ON SENSOR
Purchase Information
Add-On Sensor Setup
Delete Add-on Sensor
Lost Connection
Low Battery
15
16
16
17
17
ALARM
Setting the Alarm
Activate/Deactivate
Snooze Duration
07
08
08
PROJECTION
Projection Brightness
Adjusting the Projection
Projection Image Options
09
09
10
CHARGING
Wireless Phone Charger
Phone Compatibility
Adjustable Charging Coil
USB Charging Ports
Earbud Charging
Accesory Storage
Smart Watch Stand
Headphone Stand
Cable Organizer
11
11
12
12
13
13
14
14
15
BASICS
Press the SET button
to confirm selection and
move to next setting.
Note: Weekday will set automatically after year, month, & date settings are adjusted.
Settings Menu Order
Beep On/O • 12/24 Format • Hour • Minutes • Year • Month • Date • Fahrenheit/Celsius
Note: To enter the Settings Menu after the initial startup, hold the SET button on the top
of the clock.

1
03 04
Buttons LCD Display
BASICS BASICS
1. DISPLAY OPTION
4. PLUS +
7. SNOOZE/BACKLIGHT
2. MINUS -
5. PROJECTION
Tap to select LCD display
mode options
Scroll to rotate the projection
image (left or right)
Press to increase values,
hold to change values quickly
Press to activate/deactivate
alarm. Hold to enter alarm
settings
Press to adjust projection
intensity. Hold to change
projection mode*
Press to adjust backlight or
snooze a sounding alarm.
Hold for Auto-Dim Settings.
Hold to enter Settings
Menu
*An add-on sensor is required for additional projection options. See p.16 for details.
Press to decrease values,
hold to change values quickly
8. ROTATION WHEEL
3. SET
6. ALARM
Small accessories are stored in the bottom compartment of your clock. The Dock Cover is on the
top. Headphone stand is in the package.
AM/PM
Indicator
Alarm
Indicator
Time
Auto Dim
Indicator Calendar
Display
Modes
Calendar
Temperature
Alarm
Auto-scroll
all modes
Low Battery
Indicator
Accessories Ports
Back View
Type C USB
Charging Port
Type A USB
Charging Port
Power
Jack
Bottom View
CR2032
Backup
Battery
Use,Organize & Store
1. Smart Watch Stand
2. Earbuds Dock
3. Dock Cover
4. Small Cable Fitting
5. Large Cable Fitting
6. Headphone Stand
Top View
235
6
7
8
4
6

05 06
LCD Display Brightness Display Modes
Adjusting the LCD Display Brightness Selecting the Display Mode
Display Mode Options
Auto-Dim Settings
Press the SNOOZE/BACKLIGHT button on the top of the clock to adjust the
backlight intensity. There are 4 brightness levels, plus an o option. Tap the button on the front of the clock to
select a display mode or automatically cycle
through all of the available options.
1.
2.
3.
4.
Hold the SNOOZE/BACKLIGHT
button to enter the Auto-Dim
Settings Menu.
Program your LCD display to automatically dim during preselected times.
Press the +/- buttons to turn the
Auto-Dim feature on or o. Press
the SNOOZE/BACKLIGHT to
confirm.
Press the +/- buttons to adjust the
starting hour. Press the SNOOZE/
BACKLIGHT to confirm.
Press the +/- buttons to adjust the
stopping hour. Press the SNOOZE/
BACKLIGHT to confirm and exit.
The icon will appear on the LCD when activated.
Indoor
Temp/Humidity
The Red Icons on the right side of the LCD
indicate the current display mode.
Weekday
Month + Date
Alarm Time
ON/OFF
Outdoor
Temp/Humidity*
BASICS BASICS
Calendar
Temperature
Alarm
Auto-scroll
all modes
Display
Modes
The icon will appear on the LCD when the
Cycle Mode is active. This setting will automatically
toggle through the available display mode options.
Snooze
Countdown
*An add-on sensor is required for outdoor data. See p.16 for details.

4. Your time alarm is now activated,
indicated by the icon on the LCD.
1. Hold the ALARM button on the
top of the clock to enter the Alarm
Settings Menu.
2. Use the +/- buttons to set your
desired time. Press the ALARM
button to confirm.
3. Next, use the +/- buttons to set
your desired snooze duration (5
to 120 minutes). Press the ALARM
button to confirm and exit the Alarm
Settings Menu.
07
Time Alarm
08
Time Alarm
Ascending Alarm
Snooze Duration Countdown
The alarm will increase in frequency over a 2-minute period. After the 2-minute
time frame, the alarm will stop if not snoozed or turned o.
When your alarm sounds, press the
SNOOZE/BACKLIGHT button to snooze
your alarm for your preselected snooze
duration. A countdown will appear on
screen.
When the snooze time reaches “00,” the
alarm will sound again. The snooze feature
can be repeated as many times as desired.
Setting the Alarm
ALARM ALARM
Activating & Deactivating the Alarm
1.
2.
Press the ALARM button to
activate/deactivate the alarm
(ON/OFF).
The icon will appear on the
normal time display when the
alarm is active.

1009
Projection OptionsAdjusting the Projection Image
PROJECTIONPROJECTION
Projection Image Options
The Projection Arm tilts forwards and
backwards to adjust the location of the
projection image.
Use the Rotation Wheel on the Projection Arm to rotate the
viewing angle of the image.
Press the PROJECTION button to
adjust the projection’s brightness
(HI/LOW/OFF).
You can choose to see the (1) time, (2) outdoor
temperature and humidity, or (3) cycle through
both options.
Outdoor weather information is only available if
an add-on sensor is connected.
Selecting Your Projection Image
1.
2.
When an outdoor sensor is connected, hold the
PROJECTION button on the top of the clock
to toggle between the projection options. If no
sensor is connected, this button will only adjust
the projection’s brightness.
Time will be the default projection image. Hold and release the
PROJECTION button each time to switch between projection modes.
Note: The fixed focus projection image will look best at about 7ft. (2.1m).
Time-Only Projection
Current Time
Outdoor Temperature
and Humidity
Outdoor Temperature &
Humidity-Only Projection
Cycle Through Both Options
outdoor
Projection Brightness
*An add-on sensor is required for additional projection options. See p.15 for details.

11 12
5W Wireless Charger
CHARGING CHARGING
Charging your Qi-Enabled Phone
Phone Compatibility
• Place your Qi-Enabled phone on the platform.
Your phone should be centered and should
sit flush to the charging cradle.
• The blue Charging Indicator Light below
the platform will be solid when your phone
is successfully charging.
• The light will flash slowly if your device is
not positioned properly or if your device is
not compatible with the wireless Qi charging
technology. If this problem persists, try
removing any large/bulky cases.
Works with all Qi-Enabled phones, such as:
• iPhone 8 or newer
• Galaxy S8 or newer
• Galaxy Note 8 or newer
Compatibility may vary based on phone model and/or case selection.
This list is not comprehensive. Please check your phone’s manual for details
regarding Qi-Enabled capabilities.
Adjustable Charging Coil
As phone sizes can vary greatly,
simply slide the Phone Charger
Adjustment Handle up or down to
best match your device and get it
charging correctly.
USB Charging Ports
There is a USB Type “A” Charging Port, and a USB
Type “C” Charging Port located on the back of
your alarm clock.
• Connect your external device’s USB charging
cable (not included) into the USB Charging Port.
• Charging times may vary.
• USB Power Output: 1 Amp maximum current
Note: Although this clock is capable of
delivering 5W wireless charging, actual
charging times will be determined by
your mobile device.

13
CHARGING
Earbud Charging
1. Remove the Dock Cover from the top of the
alarm clock.
2. Open the bottom Accessory Compartment
and find the Earbud Dock and Cable Fittings.
3. Feed your earbud charging cable (not
included) up through the Earbud Dock,
securing it with the correct Large or Small
size Cable Fitting.
4. Wrap any extra cord up inside the Accessory
Compartment and feed the charging end
through the bottom hole.
5. Plug the cord into the appropriate 1 amp
USB Charging Port.
14
Smart Watch Stand
The removable Smart Watch Stand is engineered to fit
a variety of smart watch brands. Its open design allows
for easy access to your device’s unique charging port
location, for use with the included USB Charging Port.
The Earbud Dock, Cable Fittings, and Smart Watch Stand can all be stored in the
Accessory Compartment on the bottom of the clock when not in use.
How to attach the Smart Watch Stand
Accessory Storage
Open design fits most
smartwatches, including
Apple Watch
1. Remove the Smart Watch Stand from the Accessory
Compartment on the bottom of the alarm clock.
2. Insert the watch stand into the left side of the clock.
3. Place your watch on the stand and attach its
charging cord.
4. Plug the charging cord into the correct USB port.
Note: Smartwatch and charging cords not included.
CHARGING
Headphone Stand
1. Insert the Headphone Stand into the hole on the top
of the clock.
2. Place your headphones on the stand and attach their
charging cord.
3. Plug the charging cord into the correct USB port.
Note: Headphones and charging cords not included.
How to attach the Headphone Stand

15
outdoor
16
Optional Add-On Sensor
ADD-ON SENSOR
Add-On Sensor Setup
1.
2.
3.
Insert 2 “AA” Batteries into the sensor battery compartment.
Hold the +button on the clock to search for the sensor.
Press the TX button inside the sensor battery compartment to transmit a signal.
The sensor’s data should then be viewable on your LCD and as an option to be
projected.
Projection
Image
Outdoor
Temp/Humidity
Purchase Your Add-On Sensor at (or scan QR Code):
bit.ly/616a-1413_parts
You can purchase an add-on Thermo-Hygro Sensor to get real-time
temperature and humidity data, straight from your backyard.
Search for the compatible sensor using the alarm
clock’s model number (616A-1413).
CHARGING
Cable Organizer
Use the included Cable Organizer to keep
your charging cords neat and secure.
Insert the organizer into the Cable Clip
Keyhole and slide it down to lock in place.
Lift up and pull the Cable Organizer out to
remove it.
15
15
ADD-ON SENSOR
Delete Add-On Sensor
1.
2.
From normal display, press the – button to have the outdoor temperature
reading begin flashing.
Hold the – button to delete the sensor. The sensor will remain deleted until
manually reconnected.
Note: To manually reconnect the sensor, follow the Add-On Sensor Setup
steps above.

Optional Add-On Sensor
Lost Connection
ADD-ON SENSOR
• The Sensor Reception Icon will disappear from the bottom right of the LCD
and the clock will search for up to 3 minutes every hour to try to reestablish the
connection.
• To manually reconnect, hold the + button on the top of the clock to search for
the sensor.
• Dashes will show while searching for the sensor and the icon will flash for
up to 3 minutes or until the sensor is connected.
17
• If the sensor loses connection to the clock for any reason, the clock will show
NO after 30 minutes of disconnection.
The icon will appear when the sensor
batteries needs to be replaced.
Low Battery
18
Specifications
APPENDIX
Power Requirements: 5.0V Power Cord
(Included) HX18H-0503000-AU-001
CR2032 Battery for backup (Included)
The plug on the power adapter is intended
to serve as the disconnect device, the
socket-outlet shall be installed near the
equipment and shall be easily accessible.
Projection Brightness: 2 Intensity Levels + OFF
LCD Brightness: 4 Intensity Levels + OFF
(Programmable Auto-Dim Backlight Option)
Programmable Snooze Duration:
5 to 120 Minutes
Wireless Charger Power Output:
5 Watts
USB “A” and “C” Charging Port:
1 Amp Maximum Current
(Charging Cords Not Included)
Indoor Temperature Range:
32°F to 122°F(0°C to 50°C)
Indoor Humidity Range: 10% to 99% RH
Settings Backup: The CR2032 Battery
will save Time and Alarm Settings when
power is lost. Projection will not show.
8.39 in. (21.31 cm)
4.81 in. (12.21 cm)
1.80 in.
(4.57 cm)
0.35 in.
(0.88 cm)
4.35 in.
(11.04 cm)