La Crosse Technology 433-3256W User manual

21” INDOOR | OUTDOOR
ATOMIC WALL CLOCK
Model: 433-3256A / 433-3256W
DC: 100120
For information about WWVB, Atomic Time Signal visit: bit.ly/AtomicTime
Page | 1Page | 4
WARRANTY INFO
La Crosse Technology, Ltd. provides a 1-year limited time warranty (from date
of purchase) on this product relating to manufacturing defects in materials &
workmanship.
La Crosse Technology, Ltd
2830 S. 26th St.
La Crosse, WI 54601
For Full Warranty Details, Visit: www.lacrossetechnology.com/support
CARE + MAINTENANCE
• Do not mix old and new batteries.
• Do not mix Alkaline, Lithium, standard, or rechargeable batteries.
• Always purchase the correct size and grade of battery most suitable for
intended use.
• Clean the battery contacts and also those of the device prior to battery
installation.
• Ensure the batteries have with correct polarity (+ / -).
• Remove batteries from equipment that will not to be used for an extended
period.
• Promptly remove expired batteries.
All rights reserved. This manual may not be reproduced in any form, even
in part, or duplicated or processed using electronic, mechanical or chemical
process without the written permission
of the publisher.
This booklet may contain errors or misprints. The information it contains is
regularly checked and corrections are included in subsequent editions. We
disclaim any responsibility for any technical error or printing error, or their
consequences. All trademarks and patents are recognized.
WARNING: This product can expose you to chemicals including
styrene, which is known to the State of California to cause cancer. For
more information go to: www.P65Warnings.ca.gov

POWER UP
1. Remove the round Battery Cover and insert 1 AA battery into the
Center Battery Compartment. Optional: Insert batteries into the Extra
Battery Compartments. IMPORTANT: Be sure all batteries are of the
same voltage level.
2. The hands will move to the 4, 8, or 12 o’clock position and stay there
while it searches for the WWVB Atomic Time Signal. Allow up to 5
nights for the clock to receive this transmission.
3. For the best reception, place the clock on an exterior wall near a
window with the front or back of it facing Fort Collins, CO.
4. Once the Atomic Time Signal is received, the clock will set to Pacific
Time. Firmly press and hold your correct Time Zone Button until the
hands begin to spin. The time will then set correctly.
5. If you live in an area that does not follow Daylight Saving Time, while
the hands are spinning to the correct time, press the Daylight Saving
Time Button once to turn the DST setting to OFF.
Watch the setup video: bit.ly/wallclock_setup
Note: In certain areas, this clock may not be able to receive the WWVB
reception due to signal strength or interference. In this case, your clock
can be set manually until the Atomic Time Signal can be received.
Manual Set Tab
Center Battery
Time Zone Buttons
Daylight Saving Time Button
(Default is DST ON)
1. Remove all batteries from the clock.
2. Press the Manual Set Tab at least 20 times and wait 15 minutes.
3. Insert at least one battery into the Center Battery Compartment.
4. Allow the hands to spin around and stop in either the 4, 8, or 12
o’clock position.
5. Hold the Manual Set Tab until your correct time is achieved.
Note: The Atomic Time Signal will override your manual setting if the
transmission is received in the future.
4
3
2
1
MANUALLY SET TIME Ask questions, watch detailed setup videos, and provide feedback on
our social media outlets!
LET’S BE SOCIAL!
Page | 3Page | 2
Battery Requirements: 1 AA (IEC LR6) required in movement
Optional: 2 AA (IEC LR6) for added battery life
All batteries sold separately.
Battery Life: 1 Battery - 12 months, 3 Batteries - 36 months
Temperature Range: -40°F to 140°F Humidity Range: 0% to 100% RH
SPECIFICATIONS
5Optional:
Extra Battery Compartments
PTPT MTMT CTCT ETET
AA AA
AA
++++
----4
3
2
1
55
• Your thermometer and hygrometer have been pre-calibrated and
should not need adjustment.
• Before manually adjusting your sensors, allow the clock to sit at room
temperature for 2 hours.
• To manually adjust your sensors, gently turn the temperature or
humidity sensor adjustment on the back of the clock until desired
setting is reached.
Thermometer/Hygrometer