La Crosse Technology WS-7220U-IT Instruction Manual

1
WS-7220U-IT
915 MHz
Wireless Weather Station
Instruction Manual

2
TABLE OF CONTENTS
Introduction……………………………………………………………………………………..3
Inventory of Contents…………………………………………………………………………4
Quick Set Up……………………………………………………………………………………4
Detailed Set Up………………………………………………………………………………4-5
Battery Installation…………..………………………………………………………..4-5
12 or 24 Hour Time Display………..…………………………………………………..5
Time Setting………..……..…………………………………………………………….5
Features……………………………………………………………………………………….6-7
Minimum & Maximum Temperature and Humidity……………………..……………6
Resetting Minimum & Maximum Temperature and Humidity………..…………….6
Adding Additional Thermo-Hygro Sensors……………………………..…………….6
Viewing & Operating with Multiple Thermo-Hygro Sensors……………………...6-7
Mounting………………………………………………………………………………………...7
Troubleshooting……………………………………………………………………………..7-8
Maintenance & Care Instructions…………………………………………………………...8
Specifications………………………………………………………………………………..8-9
Warranty Information……………………………………………………………………...9-10

3
FIGURE 1
INSTANT TRANSMISSION is the state-of-
the-art new wireless transmission
technology, exclusively designed and
developed by LA CROSSE TECHNOLOGY.
INSTANT TRANSMISSION offers you an
immediate update (every 4 seconds!) of all
your outdoor data measured from the
transmitters: follow your climatic
variations in real-time!
This product offers:
12 or 24 Hour
Time Display
Indoor Temperature
(°F or °C)
Connection w/
Sensor Icon
Set/Channel
Button
Outdoor
Temperature (°F or °C)
Outdoor Humidity
(%RH)
Minimum/Maximum
& Plus Button
Low Battery Indicator

4
INVENTORY OF CONTENTS
1. Wireless Weather Station (Figure 1)
2. Wireless Thermo-Hygro Sensor (TX29UTH-IT) and mounting bracket. (Figure 2)
3. 3 each, 1/2” Philips screws.
4. One strip of double sided adhesive tape.
5. Instruction Manual and Warranty Card.
ADDITIONAL EQUIPMENT
(not included)
1. 1 Philips screwdriver.
2. 4 Fresh “AA” 1.5V Alkaline Batteries.
QUICK SETUP
Hint: Use good quality Alkaline Batteries; avoid rechargeable batteries.
1. Have the Wireless Weather Station and thermo-hygro sensor 3 to 5 feet
apart.
2. Batteries should be out of both units for 10 minutes.
3. Place the batteries into the thermo-hygro sensor first and next into the
Wireless Weather Station.
4. DO NOT PRESS ANY BUTTONS FOR 15 MINUTES.
In this time the Wireless Weather Station and the thermo-hygro sensor will begin to
communicate with each other, and the display will show both the indoor temperature
and an outdoor temperature. If the Wireless Weather Station does not display both
temperatures after the 15 minutes, please retry the set up as stated above. After both
indoor and outdoor temperatures are displayed for 15 minutes you can place your
thermo-hygro sensor outdoors, and set your time.
The thermo-hygro sensor should be placed in a dry, shaded area (ex: under the eve of
a roof). The thermo-hygro sensor has a range of 330 feet. Any walls that the signal will
have to pass through will reduce distance. An outdoor wall or window will have up to 20
FIGURE 2
Wireless
Thermo-hygro Senso
r
TX29UTH-IT
Mounting
Bracket

5
feet of resistance and an interior wall will have up to 10 feet of resistance. Your
distance plus resistance should not exceed 330 feet in a straight line.
NOTE: Fog and mist will not harm your thermo-hygro sensor, but direct rain must be
avoided.
DETAILED SETUP GUIDE
I. BATTERY INSTALLATION (When one thermo-hygro sensor is being used)
1. First, insert the batteries to the thermo-hygro sensor (see “A. thermo-hygro
sensor” below).
2. Within 2 minutes of powering up the sensor, insert the batteries to the Wireless
Weather Station (see “B. Wireless Weather Station” below). Once the batteries
are in place, all segments of the LCD will light up briefly. Following the indoor
temperature and the time as 12:00 will be displayed. If they are not shown in
LCD after 60 seconds, remove the batteries and wait for at least 60 seconds
before reinserting them. Once the indoor data is displayed user may proceed to
the next step.
3. After the batteries are inserted, the Weather Station will start receiving data
signal from the sensor. The outdoor temperature and humidity should then be
displayed on the Weather Station. If this does not happen after 2 minutes, the
batteries will need to be removed from both units and reset from step 1 and the
signal reception icon is no longer shown.
A. THERMO-HYGRO SENSOR
1. Remove the Battery Cover.
2. Observing the correct polarity, install 2 “AA” Alkaline Batteries—make sure they
do not spring free, or start-up problems may occur. Replace the Battery Cover.
B. WIRELESS WEATHER STATION
Note: After the batteries are installed, DO NOT press any buttons. This may interfere
with the signals, causing temperatures to register incorrectly.
1. Remove the Battery Cover on the back of the Wireless Weather Station.
2. Observing the correct polarity, install 2 “AA” Alkaline Batteries.
3. Replace Battery Cover.
4. Wait 15 minutes before pressing any buttons.
Battery
Cover
Battery
Compartment

6
*When the signal is successfully received by the Weather Station, the icon will be
switched on. (If not successful, the icon will not be shown in LCD) So the user can
easily see whether the last reception was successful (icon on) or not (icon off). On the
other hand, the short blinking of the icon shows that a reception is being done now.
C. SELECTING 12 OR 24 HOUR TIME DISPLAY
1. Press and hold the SET/CH button for about 5 seconds.
2. “12h” will begin to flash in the TIME section of the LCD
3. Press the MIN/MAX/+ button to toggle between “12h” and “24h” time.
Note:
•Selecting 12 hour time will automatically select °F as your temperature unit.
•Selecting 24 hour time will automatically select °C as your temperature unit.
4. Press and release the SET/CH button again to enter Time Setting.
D. TIME SETTING
1. After exiting the 12/24 Hour Setting, the hour will begin flashing in the time
display.
2. Press and release the MIN/MAX/+ button to select the desired hour.
Note: PM will appear to the left of the time display for PM hours. For AM hours, that
area will remain blank.
3. Press and release the SET/CH button again, and the minutes will begin to flash.
4. Press and release the MIN/MAX/+ button to select the desired minutes.
5. Press and release the SET/CH button to exit the SET UP mode.
Note: If no buttons are pressed for 10 seconds, the Wireless Weather Station will
automatically return to the normal display.
Battery
Compartment
Battery
Cove
r
Sensor signal
reception icon*

7
II. FEATURES
A. MINIMUM AND MAXIMUM TEMPERATURES AND HUMIDITY
1. Press and release the MIN/MAX button, “MIN” appears at the bottom of the LCD
and the recorded minimum temperatures and humidity are displayed.
2. Press and release the MIN/MAX button again to view maximum recorded
temperatures and humidity. “MAX” appears at the bottom of the LCD and the
maximum temperatures and humidity are displayed.
3. Press and release the MIN/MAX button once more to return to the current
temperatures and humidity.
B. RESETTING THE MINIMUM AND MAXIMUM TEMPERATURES AND HUMIDITY
To reset both the minimum and maximum temperatures and humidity—press and
hold the MIN/MAX button for 5 seconds.
C. ADDING ADDITIONAL REMOTE SENSORS (OPTIONAL)
The WS-7220U-IT is able to receive signals from 2 additional thermo-hygro sensors.
The following are instructions for the set-up of thermo-hygro sensor units with the WS-
7220U-IT. These extra sensors can be purchased through the same dealer as this unit.
1. Remove all the batteries from the receiver and sensor(s) and wait 60 seconds.
During these 60 seconds, press any button 20 times to discharge any excess
power.
2. Insert the batteries to the first thermo-hygro sensor.
3. Within 2 minutes of powering up the first sensor, insert the batteries to the
Weather Station. Once the batteries are in place, all segments of the LCD will
light up briefly. Following the indoor temperature and the time as 12:00 will be
displayed. If they are not shown in LCD after 60 seconds, remove the batteries
and wait for at least 60 seconds before reinserting them.
4. The outdoor temperature and humidity from the first sensor (channel 1) should
then be displayed on the Weather Station. If this does not happen and the signal
reception icon is not shown, after 2 minutes, the batteries will need to be
removed from both units and reset from step 1.
5. Insert the batteries to the second sensor as soon as the outdoor temperature and
humidity readings from the first sensor are displayed on the Weather Station.
NOTE: You must insert the batteries into the second sensor within 30
seconds of reception of the first sensor.
6. The outdoor temperature and humidity from the second sensor and the "channel
2" icon should then be displayed on the Weather Station. If this does not happen
after 2 minute, the batteries will need to be removed from all the units and reset
from step 1.
7. Insert the batteries to the third sensor as soon as the "channel 2" icon and
outdoor data are displayed on the Weather Station. Then within 2 minutes, the
channel 3 outdoor data from the third sensor will be displayed and the channel
icon will shift back to "1" once the third transmitter is successfully received. If this
is not happen, user shall restart the setting up from step 1.

8
NOTE: You must insert the batteries into the third sensor within 30 seconds of
reception of the second sensor.
IMPORTANT: Transmission problems will arise if the setting for multiple sensors
is not followed as described above. Should transmission problems occur, it is
necessary to remove the batteries from all units and start again the set-up from
step 1.
D. VIEWING AND OPERATING WITH MULTIPLE REMOTE SENSOR UNITS
1. To view the temperature of a different thermo-hygro sensor unit, press and release
the SET/CH button. A shift from one “boxed” number to the next should be
observed on the right side of the OUTDOOR LCD.
2. To view the Minimum/Maximum temperature & humidity: first select from which
thermo-hygro sensor to read data (indicated by the “boxed” number). Pressing and
releasing the MIN/MAX button will toggle through the minimum and maximum
indoor temperature, and the minimum and maximum outdoor temperature and
humidity.
3. To reset the Minimum/Maximum readings, press and hold the MIN/MAX button for
5 seconds.
III. MOUNTING
Note: To achieve a true temperature reading, avoid mounting in direct sunlight. We
recommend that you mount the thermo-hygro sensor on an outside North-facing wall
(under the eve of a house is ideal). The sending range is 330 feet; obstacles such as
walls, stucco walls, concrete, and large metal objects will reduce the range. Place the
Wireless Weather Station and thermo-hygro sensor in their desired locations before
permanently mounting.
A. THERMO-HYGRO SENSOR
The thermo-hygro sensor can be mounted in two ways:
•with the use of screws, or
•using the adhesive tape.
A. MOUNTING WITH SCREWS
1) Remove the mounting bracket from the remote thermo-hygro
sensor.
2) Place the mounting bracket over the desired location.
3) Through the three screw holes of the bracket, mark the
mounting surface with a pencil.
4) Screw mounting bracket onto the mounting surface. Ensure
that the screws are flush with the bracket.
5) Insert the thermo-hygro sensor into the bracket.

9
B. MOUNTING WITH ADHESIVE TAPE
Note: The adhesive tape is not intended to be used as a permanent
mounting solution. Only use the adhesive tape while you are
positioning the Weather Station and thermo-hygro sensor.
1) With a nonabrasive solution, clean and dry the back of the
mounting bracket and the mounting surface to ensure a secure
hold. The mounting surface should be smooth and flat.
2) Remove the protective strip from one side of the tape.
3) Adhere the tape to the designated area on the back of the
mounting bracket.
4) Remove the protective strip from the other side of the tape.
5) Position the remote thermo-hygro sensor in the desired location,
ensuring that the Weather Station can receive the signal.
B. WIRELESS WEATHER STATION
1. The Wireless Weather Station comes with the table stand
attached to the back of the Receiver. If you wish to use the
table-stand, simply place the Wireless Weather Station in an
appropriate location, and pull out on the attached stand.
2. To wall mount, push the table stand flat against the Wireless
Weather Station (if it isn’t already flat). Fix a screw (not
included) into the desired wall, and place the Wireless Weather
Station onto the screw using the hanging hole on the backside.
Gently pull the Wireless Weather Station down to lock the screw
into place.
TROUBLESHOOTING
NOTE: For problems not solved, please contact La Crosse Technology via e-mail or
phone, or visit our website, www.lacrossetechnology.com
Problem: The LCD is faint
Solution: Replace batteries
Problem: No outdoor temperature is displayed.
Solution:
1) Bring any units from outside, inside and place the units 3 to 5 feet apart with
nothing in-between them.
2) Remove the batteries from all units.
3) Press one of the buttons on the Wireless Weather Station display at least 20
times to clear all memory. Verify that the display is blank before proceeding.
4) Using good quality alkaline batteries, place the batteries back into the outdoor
temperature sensor; making sure they are installed according to the diagrams in
the battery compartment.

10
5) Taking care not to press any buttons, reinstall the batteries in the Wireless
Weather Station according to the diagram in the battery compartment.
6) Do not press any buttons for at least 15 minutes after installing the batteries.
(This is to let the units establish a good connection.)
7) During the course of the 15 minutes an outdoor temperature should appear on
the display. You can now put your sensor(s) back outside.
MAINTENANCE AND CARE INSTRUCTIONS
•Extreme temperatures, vibration, and shock should be avoided to prevent damage to
the units.
•Clean displays and units with a soft, damp cloth. Do not use solvents or scouring
agents; they may mark the displays and casings.
•Do not submerge in water.
•Do not subject the units to unnecessary heat or cold by placing them in the oven or
freezer.
•Opening the casings invalidates the warranty. Do not try to repair the unit. Contact
La Crosse Technology for repairs.
SPECIFICATIONS
Transmitting
Frequency 915 MHz
TEMPERATURE MEASURING RANGES
Indoor 14.1°F to 139.8°F with 0.2°F resolution.
Outdoor -39.8 °F to 139.8°F with 0.2°F resolution.
HUMIDITY MEASURING RANGE
Outdoor(%RH) 1% to 99%
Transmitting range Maximum 330 feet (100m) open space
TEMPERATURE CHECKING INTERVAL
Indoor Every 15 seconds
Outdoor Every 4 seconds
BATTERIES—(Alkaline recommended)
Thermo-Hygro Sensor 2 x AA, 1.5V
Wireless Weather
Station 2 x AA, 1.5V
DIMENSION: (H x W x D)
Wireless Weather
Station 5.90” x 2.36” x 0.81”
(150 x 60 x 20.7mm)