La Spaziale S11 BRIO Specification sheet

1 MUM S11MINIBRIO_ENG REV01
INSTRUCTIONS FOR USE
AND MAINTENANCE
REV 01
La Spaziale SpA Via E. Duse, 8 40033 Casalecchio di Reno Bologna - (Italy) tel. [phone] fax. [phone]
[email protected]
www.laspaziale.com

2 MUM S11MINIBRIO_ENG REV01
GENERAL DESCRIPTION OF THE MACHINE:
1
2
3
4
5
6
10
9
11
12
13
14
8
7
15
15

3 MUM S11MINIBRIO_ENG REV01
1) WATER TANK FILLING LID
2) CUP HOLDER TRAY
3) WATER TANK ACCESS LID
4) DELIVERY GROUP PUSHBUTTON PANEL
5) DELIVERY GROUP LED STATUS BAR
6) COFFEE DELIVERY GROUP N. 1
7) DRIP TRAY COFFEE MODULE
8) PRESSURE MANOMETER GROUP 1 PUMP
9) HOT WATER SPOUT FOR INFUSIONS
10) DRIP TRAY WATER DELIVERIES
11) STEAM NOZZLE
12) USB CONNECTION
13) TFT MAIN DISPLAY TOUCHSCREEN
14) MAIN PUSHBUTTON PANEL (ON/ STBY; INFUSED WATER DELIVERIES; STEAM DELIVERIES)
15) SIDE LED WATER TANK

4 MUM S11MINIBRIO_ENG REV01
GENERAL DESCRIPTION OF THE CONTROL PANEL:
1
2
3
4
5
6
7
8
9
10
11
12
13
14

5 MUM S11MINIBRIO_ENG REV01
1) DELIVERY GROUP PURGE FUNCTION BUTTON
2) GROUP 1 SHORT COFFEE DELIVERY BUTTON
3) DELIVERY BUTTON 1 LONG COFFEE / 2 COFFEES (according to appliance parameters) DELIVERY GROUP
4) GROUP CONTINUOUS DELIVERY BUTTON
5) DELIVERY GROUP ON / STBY BUTTON
6) STEAM DELIVERY BUTTON (IF STEAM BOILER IS ON)
7) APPLIANCE ON/ STBY BUTTON
8) INFUSED WATER DELIVERY BUTTON (IF STEAM BOILER IS ON)
9) GROUP 1 SHORT COFFEE DELIVERY BUTTON LED
10) DELIVERY BUTTON LED 1 LONG COFFEE 2 COFFEES (according to appliance parameters) DELIVERY GROUP
11) DELIVERY GROUP CONTINUOUS DELIVERY BUTTON LED
12) STEAM DELIVERY BUTTON LED.
13) APPLIANCE ON / STANDBY LED
14) INFUSED HOT WATER DELIVERY LED

6 MUM S11MINIBRIO_ENG REV01
WATER MAINS CONNECTION SETUP (OPTIONAL):
N.B.: Do not apply excessive force when connecting the hose to the fitting.
¾ GAS WATER MAINS
CONNECTION

7 MUM S11MINIBRIO_ENG REV01
APPLIANCE DATA PLATE
Remove the delivery group drip tray to view the appliance data plate:

8 MUM S11MINIBRIO_ENG REV01
READ THE FOLLOWING WARNINGS CAREFULLY AS THEY PROVIDE IMPORTANT SAFETY INFORMATION ON APPLIANCE USE AND MAINTENANCE
This appliance must be used solely for its intended purpose and installed in a suitable place for such use. Any other use is to be considered
improper and therefore hazardous. The manufacturer will not be held responsible for any damage caused due to improper, incorrect or hazardous
appliance use.
The appliance must be installed in compliance with current legislation and according to the manufacturer’s instructions.
Incorrect installation may cause damage to people, animals or property and the manufacturer will not be held liable.
The electrical safety of this appliance is ensured when it is correctly connected
to an efficient earthing system, as provided for in legislation in force.
The electrical system to which the appliance is connected (by the client) must be compliant with legislation in force.
This fundamental requirement must be verified by professionally qualified staff.
The manufacturer will not be held responsible for any damage caused due to the absence or inefficiency of a good earthing system, or for its
non conformity with legislation in force.
When using any electrical appliance, the following fundamental regulations must also be observed:
• Do not touch the appliance with wet or damp hands or feet.
• Do not use the appliance barefooted.
• Do not pull on the power cord to disconnect the appliance from the mains.
• Do not allow the appliance to be used by children or unauthorised persons.
• Access to the appliance area should be strictly reserved to people familiar with and who have practical experience of operating the appliance,
especially in regards to hygiene and safety.
• Before carrying out any scheduled cleaning or maintenance work, disconnect the appliance from the electrical mains.
• If the appliance becomes faulty and/or malfunctions, or if the power cord becomes damaged, fully switch off the appliance and do not attempt
any direct repairs. Contact the manufacturer-authorised Help Centre only.
• To ensure efficient and correct appliance operation, follow the manufacturer's instructions when carrying out any scheduled maintenance.
• The appliance’s protection against electrocution gives it a class I protection rating.
• The appliance must operate in an environment where the temperature is between +5°C and 40°C.
• The appliance is not intended for use in an outdoor environment where it is directly subject to atmospheric agents.
• When operating normally, the acoustic noise emitted by the appliance is less than 70 dB.

9 MUM S11MINIBRIO_ENG REV01
The appliance is supplied without water in the boiler, to avoid damage from exposure to low temperatures; for this very reason, if the
appliance is unused for a long time, water should be removed from the boiler before disconnecting it.
Failure to comply with the above may impair the safety of the appliance and its
service life.
If the appliance remains unused for a long period of time in a place where the temperature is below 0°C, before starting it up, call the
Authorised Help Centre to verify appliance condition.
INSTALLATION
• The appliance is not designed to be built-in.
• After removing the packaging, check the condition of the appliance. If any doubts arise, do not use it and contact the manufacturer directly.
Packaging materials must not be left in the reach of children as they are a potential hazard. Lift the appliance up by its sides and set it down on a
secure support surface.
• The appliance must be installed so that the plug which disconnects the appliance from the electrical mains is still accessible.
• Installation must be carried out in areas where use and maintenance is restricted to trained staff only.
Before plugging the appliance into the mains socket, check that data plate details are the same as those for the installation site.

10 MUM S11MINIBRIO_ENG REV01
INSERTING RESIN BAG TO SOFTEN WATER
A resin bag is supplied with the appliance, which is necessary for softening water before use (removal of limescale).
Remove the resin bag from its packaging and thoroughly rinse under running water for around 1 minute.
Remove the water tank cover 1 (PAGE2), lift the cover below and place the bag in the tank:
Correctly reposition the items to close the tank compartment.

11 MUM S11MINIBRIO_ENG REV01
AUTOMATIC CYCLE FOR THE FILLING OF THE GROUP DELIVERY WATER CIRCUIT UPON INITIAL START-UP
REFER TO THE COMPONENTS KEY ON PAGES 2-4 WHEN FOLLOWING THE INSTRUCTIONS BELOW
1) Insert the plug into the power socket. The LED 13 (PAGE4) will flash to indicate that the appliance is connected to the electrical mains
(STANDBY).
2) Hold down the button 7 (PAGE4) for more than 3 seconds: the LED 13 (PAGE4) will stop flashing and remain on, meaning that the
appliance has been successfully switched on.
3) The following will be displayed on the main display 13 (PAGE2):
If you have not already done so in the previous step, add the resin bag that comes supplied with the appliance, as described on PAGE10, manually
add around 1 litre of cold water, after lifting tank cover 1 (PAGE2), up to the minimum level marked on the tank.
PLEASE NOTE: When filling the tank, avoid spilling water out of the filling hole!

12 MUM S11MINIBRIO_ENG REV01
Upon reaching the minimum level, the Display will read:
Press on the "START FILLING CYCLE", ensure the Coffee tray 7 (PAGE2) of Delivery Group 6 (PAGE2) are in position.
The appliance will now start an automatic filling cycle of the delivery group, which will last 30 seconds; during this time, water will start coming
out of delivery group 6 (PAGE2).

13 MUM S11MINIBRIO_ENG REV01
Once the filling cycle finishes, the Display will read:
Press the button to end the water cycle filling procedure, only required when commissioning the appliance.
The Display will return to STBY, with LED 13 (PAGE4) flashing only.

14 MUM S11MINIBRIO_ENG REV01
SUPPLYING THE APPLIANCE WITH WATER:
The appliance can be supplied with water (filling the water tank) in two ways, according to settings integrated in management firmware:
-MANUAL SUPPLY: The rear water tank (2.8 Lt capacity approximately) must be manually filled: lift the cover 1 (PAGE2) and add water.
-DIRECT SUPPLY FROM WATER MAINS (OPTIONAL): The rear tank is automatically filled by means of the hose supplied and connected to
the lower appliance fitting as illustrated on PAGE 6
REFER TO THE FILLING METHOD PRE-INSTALLED ON THE APPLIANCE, OR SET DURING INSTALLATION BY AN
AUTHORISED TECHNICIAN.
SWITCHING THE APPLIANCE ON:
With appliance connected to electrical mains and in STBY mode (only LED 13 PAG2 flashing), press and hold down the button 7 for 3 seconds
(PAGE4):
The following will appear on the display, according to tank water level:

15 MUM S11MINIBRIO_ENG REV01
In this case, the Display will indicate that the water level in the rear tank is insufficient.
Consequently, manual filling is required: proceed as described here below:
FILLING THE WATER TANK (MANUAL WATER TANK FILLING):
Lift the cover 1 (PAGE2) and fill the tank with cold drinking water until the no water warning message is no longer displayed and the side
panel LEDS 15 (PAGE2) are no longer flashing. Fill with more water, checking the water level from the side inspection windows all the while.
N.B.: Do not fill the tank with too much water and in any case, stop filling with water when the icon appears in the main display, in order
to prevent any water from overflowing.
N.B.: IF THE APPLIANCE IS CONNECTED TO THE WATER MAINS (OPTIONAL), THE TANK FILLING CYCLE WILL AUTOMATICALLY START WHEN THE
APPLIANCE IS SWITCHED ON. THE CYCLE WILL END ONCE FILLED TO THE MAXIMUM LEVEL.
When the tank has been filled with water, the following will be displayed on the main display:
The delivery group and/or steam Boiler can now be switched on.

16 MUM S11MINIBRIO_ENG REV01
SWITCHING ON THE COFFEE DELIVERY GROUP:
Press button 5 (PAGE4) to switch on the coffee delivery group.
The following will be displayed on the main display:
The front LED bar 5 (PAGE2) and leds of delivery pushbutton panel selections 4 (PAGE2) will light up.
As the delivery group heats up, the temperature value (expressed in °C) is displayed in red. It will turn green when set temperature is reached (this
can be changed in the specific menu, see the section here below). Whenever the temperature drops below the set temperature, the number turns
red (heating-up phase) until the set temperature is reached again (green).

17 MUM S11MINIBRIO_ENG REV01
To disable the delivery groups, press the relative button 5 (PAGE4) for longer than half a second. The front LED bar 5 (PAGE2) will switch off.
TURNING ON THE STEAM BOILER:
With the appliance switched on, press the button on the Touchscreen display to enable steam boiler heating (hot water for
infusions/steam). The LEDs 12 and 14 (PAGE4) will light up and steam boiler pressure (expressed in Bars) will be displayed:
The steam boiler automatic water filling cycle will start and when it ends, the heating phase will begin.
To turn off the steam boiler, hold down the button for longer than half a second.

18 MUM S11MINIBRIO_ENG REV01
PREPARING COFFEE:
When the correct operating temperature of the delivery group is reached (value in °C in green), proceed as follows:
1. Unhook the filter holder of the display group (6) PAGE2.
2. Load ground coffee (use coffee doser supplied), take care not to leave any coffee powder on the upper edge of the filter holder, and press using the coffee
press supplied.
3. Hook the filter holder back onto the delivery group (6) PAGE2, firmly but not too tightly.
4. Place one or two coffee cups under the filter holder.
Select the 1 short coffee button (2 PAGE4), 1 long coffee button (3 PAGE4) or continuous delivery button (4 PAGE4) to start delivery. If using
selections with automatic doses, the appliance will stop delivery when the set amount has been delivered, based on programmed product values
entered upon installation. If continuous delivery is selected, when the desired amount of coffee is delivered into the cup, press the button once
more to stop delivery.
The amount of coffee delivered can be modified through programmable selections: please refer to the relevant chapter here below.
PLEASE NOTE: When using the appliance, frequently check tray 7 levels (PAGE2) and if necessary, empty it.
STEAM DELIVERY:
With the steam boiler ON and pressurised (approximately 1 - 1.2 bar as shown on the main Display), insert the steam wand 11 (PAGE2) into a
frothing jug with the beverage that requires heating and press the button 6 (PAGE4).
Once the beverage has been heated up, press button 6 (PAGE4) again to stop steam delivery.
PLEASE NOTE: Do not press button 6 (PAGE4) before inserting the steam wand 11 (PAGE2) into the frothing jug, to avoid the risk of burning yourself.

19 MUM S11MINIBRIO_ENG REV01
HOT WATER DELIVERY FOR INFUSIONS:
With the steam boiler ON and pressurised (approximately 1 - 1.2 bars, as shown on the main Display), position a frothing jug underneath the hot
water delivery spout 9 (PAGE2).
Press the hot water delivery button 8 (PAGE4). Hot water delivery will begin.
When the desired amount has been delivered, press again the button 8 (PAGE4) to stop delivery.
PLEASE NOTE: Do not press button 8 (PAGE4) before placing a frothing jug below the hot water delivery spout 9 (PAGE2), to avoid being burnt.
ACCESSING THE APPLIANCE PROGRAMMING/ SETTINGS MENUS:
To access the appliance settings/ parameters menu, proceed as follows:
With the appliance ON, press the button on the Touch Display for more than a second and the following will appear on the Display:
Enter the 4-digit PIN to access the menus (DEFAULT PIN: 0000) and confirm by pressing the button.

20 MUM S11MINIBRIO_ENG REV01
N.B.: If no PIN is entered after 5 seconds, the display will return to the main screen.
The default PIN can be changed in the specific menu by following the procedure described in the relevant chapter.
When the correct PIN is confirmed, the following will appear on the Display:
Use the and buttons to scroll through the menus, and select the desired Area to access them.