Lafayette EZ-Charge V2 Installation manual

EZ-Charge V2
Mul-Channel Remote
FCC Compliance
This device complies with Part 15 of the FCC Rules. Operaon is subject to the following two condions
[1] This device may not cause harmful interface, and
[2] This device must accept any interference received, including interference that may cause undesired op-
eraon.
Package Contents
1 x 15 channel remote
1 x magnec holder including wall xing screws
1 x 3V CR2450 baery
For Motorizaon Technical Support call 877-548-0612
EZ-Charge Programming Instructions

Installaon
Wall Mount Holder
Remove cover from base by prying with at
head screwdriver
Used supplied fasteners and anchors to
aach the base to the wall
Replace cover by pressing snap latches into
place.
Baery
Remove cover from remote press gently in
and down to disengage cover.
Install baery with posive (+) side facing
up.
For Motorizaon Technical Support call 877-548-0612

Programming
Pairing Motor to a Remote
Select channel on controller Hold P1 buon on the motor head
for 1 jog
Hold STOP on controller
Motor Response Motor Response
Check Motor Direcon
To check travel direcon of shade, press UP
or DOWN on controller.
To reverse shade direcon, hold both UP
and DOWN.
Motor Response
Seng Limits
Move shade to desired highest or lowest
posion by pressing the UP or DOWN
buons
Holding DOWN will make the shade travel.
Pressing DOWN buon moves the shade in
small movements. You must press the
STOP buon if the shade is traveling.
Holding UP will make the shade travel.
Pressing UP buon moves the shade in
small movements. You must press the
STOP buon if the shade is traveling.
Once you are at your upper limit, hold UP and
STOP.
Once you are at your lower limit, hold DOWN
and STOP.
DONE!
For Motorizaon Technical Support call 877-548-0612

Adjusng Upper Limit
You can do this at ANY posion. Shade does not need to be at the current upper limit.
Hold UP and STOP on the
controller.
Move shade to desired
posion
Hold UP and STOP on the
controller.
Adjusng Lower Limit
You can do this at ANY posion. Shade does not need to be at the current lower limit.
Hold DOWN and STOP on
the controller.
Move shade to desired
posion
Hold DOWN and STOP on
the controller.
Copy / Delete channels
Hold P1 buon on the motor
head for 1 jog.
Select channel you wish to
add or delete
Hold the STOP buon on the
controller
Delete All Sengs
Hold P1 on the motor head
for 4 connuous jogs
For Motorizaon Technical Support call 877-548-0612

Favorite Posion
You will need to put a motor to sleep if you are going to program mulple shades on the same channel or adjust a limit for a
specic shade on a group channel. To wake the shade up just press and release the P1 motor head buon.
Hold P1 on the motor head
for 2 connuous jogs
Pung motor to sleep
Move shade to the desired favorite posion
Remove baery door on remote.
Press and release P2 on the upper
le corner. The shade will jog once.
Press and release the STOP
buon on the controller
and the shade will jog
Press and release the STOP
buon on the controller
and the shade will jog
For Motorizaon Technical Support call 877-548-0612

Tilt Mode
Hold UP and DOWN on the
controller for 1 jog
Hold UP and DOWN on the
controller for 1 jog
In this mode if you just press and release a direcon the shade will only move in small increments. This is nice for the Transional
shades. If you want the shade to travel all the way up or all the way down , press and HOLD that direcon. To exit this mode and
revert back to Roller Mode, do the same steps.
Adjusng Motor Speed
Remove baery door on remote.
Press and release P2 on the upper
le corner. The shade will jog once.
Press UP shade will make 1
jog
Press UP shade will make 2
jogs
To Increase speed
Press DOWN shade will
make 1 jog
Press DOWN shade will
make 2 jogs
To decrease speed
For Motorizaon Technical Support call 877-548-0612

EZ-Charge V2
Surface Mounted Wireless Wall Switch
FCC Compliance
This device complies with Part 15 of the FCC Rules. Operaon is subject to the following two condions
[1] This device may not cause harmful interface, and
[2] This device must accept any interference received, including interference that may cause undesired op-
eraon.
Package Contents
1 x Switch
1 x Single gang Decora style wall plate (incl 2 mounng screws)
1 x 3V CR2430 baery
For Motorizaon Technical Support call 877-548-0612

Installaon
Wall Mount Holder
Open rear baery cover by gently separang
switch covers with screwdriver
Install CR2430 baery with posive side facing
up. Snap covers back together.
Baery
For Motorizaon Technical Support call 877-548-0612
Used supplied fasteners and anchors as
needed to aach base.

Programming
Pairing Motor to a Remote
Select channel on controller Hold P1 buon on the motor head
for 1 jog
Hold STOP on controller
Motor Response Motor Response
Check Motor Direcon
To check travel direcon of shade, press UP
or DOWN on controller.
To reverse shade direcon, hold both UP
and DOWN.
Motor Response
Seng Limits
Move shade to desired highest or lowest
posion by pressing the UP or DOWN
buons
Holding DOWN will make the shade travel.
Pressing DOWN buon moves the shade in
small movements. You must press the
STOP buon if the shade is traveling.
Holding UP will make the shade travel.
Pressing UP buon moves the shade in
small movements. You must press the
STOP buon if the shade is traveling.
Once you are at your upper limit, hold UP and
STOP.
Once you are at your lower limit, hold DOWN
and STOP.
DONE!
For Motorizaon Technical Support call 877-548-0612

Adjusng Upper Limit
You can do this at ANY posion. Shade does not need to be at the current upper limit.
Hold UP and STOP on the
controller.
Move shade to desired
posion
Hold UP and STOP on the
controller.
Adjusng Lower Limit
You can do this at ANY posion. Shade does not need to be at the current lower limit.
Hold DOWN and STOP on
the controller.
Move shade to desired
posion
Hold DOWN and STOP on
the controller.
Copy / Delete channels
Hold P1 buon on the motor
head for 1 jog.
Select channel you wish to
add or delete
Hold the STOP buon on the
controller
Delete All Sengs
Hold P1 on the motor head
for 4 connuous jogs
For Motorizaon Technical Support call 877-548-0612